Subscribe to Our Youtube Channel
Related Manuals for mastro ADH3007
Summary of Contents for mastro ADH3007
- Page 1 014_03 04/2006 Installation, operating and maintenance instructions GAS FRY TOP ADH3007 · ADH3008 ADH3009 · ADH3010 ADH3011 · ADH3012 AEH3007 · AEH3008 AEH3009 · AEH3010 AEH3011 · AEH3012...
-
Page 2: Table Of Contents
INDEX Replacing parts Models and dimensions page page Ignition plug Gas tap Data of appliances Thermocouple Technical data Using the appliance Smooth, grooved and chrome plates Operating instructions using and start-up Construction, equipment installed First time use of the plate and safety devices Ignition Assembly... - Page 3 Dimensions ADH30007 / ADH30008 ADH30009 / ADH30010 ADH30011 / ADH30012 Gas connection Data plate 014 - 03 - Gas fry-top...
- Page 4 Dimensions AEH30007 / AEH30008 AEH30009 / AEH30010 AEH30011 / AEH30012 Gas connection Data plate 014 - 03 - Gas fry-top...
-
Page 5: Technical Data
2 - CHARACTERISTICS OF THE APPLIANCES control panel. It contains all necessary reference data such as the The instructions contained in this manual apply to our gas fryers in the II2H3+ category (see table on page 6). name of the manufacturer, input pressure, gas type setting, etc. The data plate is located on the front of the appliance and on the CAT/KAT GAS/GAZ... - Page 6 TABLE 1 ADH30007 · ADH30008 ADH30009 · ADH30010 Model AEH30007 · AEH30008 ADH30011 · ADH30012 AEH30009 · AEH30010 AEH30011 · AEH30012 Category II2H3+ Construction type Air necessary for combustion 6.2 + 6.2 = 12.4 Nominal thermal power 2.6 + 2.6 = 5.2 Minimum thermal power Connection pressure Methane gas 2H...
-
Page 7: Operating Instructions
OPERATING INSTRUCTIONS Construction, equipment installed and Legal and technical requisites safety devices During assembly, the following legal and technical requi- Robust steel frame, with 4 legs (adjustable in height). sites should be adhered to: 18/10 chrome-nickel steel outer panelling. The surface of the special steel plate can be either - relevant national legislation;... -
Page 8: Commissioning The Appliance
COMMISSIONING THE APPLIANCE Before commissioning the appliance It is normally enough, however, simply to check that the Before commissioning the appliance, remove the protec- nozzles are functioning correctly. tive wrapping. Thoroughly clean the work-surface and the outside of the Checking input pressure (Fig. 3) appliance using lukewarm water and detergent. -
Page 9: Checking The Pilot Light
Checking the pilot light rent types of gas, marked in 100ths of mm, are in a case When correctly adjusted, the pilot light flame will comple- supplied with the appliance (the pilot burner nozzles are tely surround the thermocouple and will not flicker; if it marked with a code number). -
Page 10: Maintenance
the Gas Flow Setting Table (2); REPLACING PARTS - start the appliance up according to the instructions; - after allowing the appliance to run for 45 mins., turn All parts must be replaced by authorised technicians the knob to low and set minimum gas flow by turning only! screw (36) (to the right = gas flow decreases;... -
Page 11: First Time Use Of The Plate
USING THE APPLIANCE SMOOTH GROOVED AND CHROME - The minimum for the thermostatic valve is in position 1 PLATES START-UP and the maximum in position 7 (With thermostatic valve) TURNING THE APPLIANCE OFF FIRST-TIME USE OF THE PLATE Important! Turning the appliance off during Before using the appliance for the first time, thorough- normal operation ly clean the smooth or grooved surface of the plate... -
Page 12: What To Do If Something Goes Wrong Or If Not Using The Appliance For A Long Time
What to do if something goes wrong or if not using the appliance for a long time If the appliance is not to be used for a long time, or if it breaks down or works incorrectly, close the tap to the gas mains located outside the appliance. -
Page 13: Warning
WARNING DUE TO ITS POLICY OF CONTINUAL PRODUCT IMPRO- VEMENT, THE MANUFACTURER RESERVES THE RIGHT TO MAKE ANY CHANGES DEEMED NECESSARY. THE MANUFACTURER CANNOT BE HELD RESPONSI- BLE IF THE INSTRUCTIONS CONTAINED IN THIS MA- NUAL ARE NOT OBSERVED. 014 - 03 - Gas fry-top...
Need help?
Do you have a question about the ADH3007 and is the answer not in the manual?
Questions and answers