Table of Contents
Advertisement
Quick Links
TM
OPERATING MANUAL
This manual MUST be kept and stored with the aerial platform at all times.
800 275-9522
For Service please call .....................................................................
Skyjack Inc. Service Center 3451 Swenson Ave., St. Charles, IL. 60174 ..... FAX 630 262-0006
800 965-4626
For Parts in North America and Asia please call .....................................
Skyjack Inc. Parts Center 3451 Swenson Ave., St. Charles, IL. 60174 .............. FAX 888 782-4825
31 297 255 526
For Parts & Service in Europe please call ....................................................
Skyjack Europe Communicatieweg 29, 3641 SG Mijdrecht Netherlands ............. FAX 31 297 256 948
118931AH
Printed in Canada
May 2002
Advertisement
Table of Contents
Related Manuals for Skyjack SJIII 6826E
Summary of Contents for Skyjack SJIII 6826E
- Page 1 This manual MUST be kept and stored with the aerial platform at all times. 800 275-9522 For Service please call ..............Skyjack Inc. Service Center 3451 Swenson Ave., St. Charles, IL. 60174 ..FAX 630 262-0006 800 965-4626 For Parts in North America and Asia please call ........
- Page 2 WARNING This Operating Manual and the “ANSI/SIA Manual Of Responsibilities” are considered fundamental parts of the elevating work platform. They are a very important way to communicate necessary safety information to users and operators. A complete and legible copy of these manuals MUST BE KEPT ON THE WORK PLATFORM in the provided weather resistant storage compartment at all times.
-
Page 3: Table Of Contents
Table Of Contents Section - Paragraph Page No. Section 1 - Introduction Purpose Of Equipment ........................7 Use Of Equipment ..........................7 Warnings ............................7 Description ............................7 Operator Warnings ........................... 8 Specifications And Features ......................9 Standard Features And Optional Equipment ................10 Work Platform Major Component Identification ................ - Page 4 You, as a careful operator, are the best insurance against an accident. Therefore, proper usage of this work platform is mandatory. The following pages of this manual should be read and understood completely before operating the work platform. Any modifications from the original design are strictly forbidden without written permission from SKYJACK, Inc. DANGER ELECTROCUTION HAZARD THIS MACHINE IS NOT INSULATED.
- Page 5 SKYJACK, Inc. warrants each new SJIII Series work platform to be free of defective parts and workmanship for the first 12 months. Any defective part will be replaced or repaired by your local SKYJACK dealer at no charge for parts or labor.
- Page 6 (4) hours. If a part to Skyjack within 15 days from the time of billing. has serviceable components, PLEASE replace the bad When work platforms are put into stock, the warranty component.
-
Page 7: Section 1 - Introduction
Purpose Of Equipment Lifting Mechanism - The lifting mechanism is The SKYJACK SJIII Series Work Platform is designed constructed from steel tubing making up a scissor-type to transport and raise personnel, tools and materials assembly. The scissor-type assembly is raised and to overhead work areas. -
Page 8: Operator Warnings
Optional Accessories Warning The SKYJACK SJIII Series Work Platform is designed Work Platform Conditions to accept a variety of optional accessories. These are listed in (Table 1-2.) Standard Features and Optional Equipment. Operating instructions for these An Operator Should Not Use Any... -
Page 9: Specifications And Features
Table 1-1. Specifications and Features Model 6826E 6832E Weight Ω 68.00” 68.00” Width (1.73m) (1.73m) 99.25” 99.25” Length (2.52m) (2.52m) 60” x 81” 60” x 81” Platform Size (1.53x2.05m) (1.53x2.05m) 32.00’ 38.00’ Elevated Working (9.75m) (11.60m) 26.00’ 32.00’ Elevated Platform (7.92m) (9.75m) 93.6”... -
Page 10: Standard Features And Optional Equipment
Table 1-2. Standard Features And Optional Equipment Standard Features (ANSI & CE) Optional Equipment (ANSI & CE) • Descent Alarm • Spring-Loaded Half-Height Gate (ANSI only) • Proportional Joystick Forward/Reverse and Lift • Spring-Loaded Full-Height Gate Control • Movement Alarm •... -
Page 11: Work Platform Major Component Identification
Work Platform Major Component Identification OPERATOR’S CONTROL BOX EXTENSION MAIN PLATFORM PLATFORM LIFTING MECHANISM HYDRAULIC/ ELECTRIC TRAY BASE BATTERY TRAY Figure 1-1. SJIII Series Work Platform (Model 6832E shown) SJIII Series E - The CONVENTIONALS SECTION 1, Page 11 May 2002 118931AH... -
Page 12: Section 2 - Operation
SECTION 2 OPERATION Operating Controls Identification 5- Enable Switch - this switch, when activated, brings power to the Up/Down Toggle switch. The following descriptions are for identification, explanation and locating purposes only. A qualified Emergency Battery Disconnect Switch operator MUST read and completely understand these descriptions before operating this work platform. -
Page 13: 1500W Ac Inverter (Option)
1500W AC Inverter (Option) 1- Lift/Drive Function Controller - A one-hand toggle- type lever to control drive/lift motion and steer motion. It is a “deadman” control which returns to neutral when released. 2- Lift/Drive Enable Switch - This momentary “Trigger” style switch (on later models) energizes the proportional controller. -
Page 14: Outrigger Control Box
Outrigger Control Box Warning Alarm And Indictor Light Light Indicator on control box (Figure 2-4) will glow and an alarm will sound when an unsafe condition occurs. Examples are: Machine is in a tilted position. Outriggers are out of a set position. (Not Fully extended or retracted.) (if equipped) Platform is overloaded. -
Page 15: Operator Qualifications
Operator Qualifications First Aid Immediately flush eyes with cold water if electrolytic acid is splattered into them. Seek medical attention Only trained and authorized persons should use this if discomfort continues. work platform. Safe use of this work platform requires the operator to understand the limitations and In the battery tray, check the electrolyte level in warnings, operating procedures and operator’s... -
Page 16: Prestart Checks
Inspect all hoses, fittings, wires, cables, valves, Check overhead clearances. etc. for leaks, hidden damage and foreign material. Make sure the batteries are fully charged. Disconnect the AC charger cord from the 13A. On (CE) machines: external power source. Raise the platform, by selecting “BASE” position, with the Platform/Off/Base Select Switch (Figure 2- Make sure all guardrails and lockpins are in place... -
Page 17: Start And Operation
Start and Operation Note Using the controls on the base: A lowering warning system is standard on (CE) Models Turn Emergency Power Disconnect Switch to This system automatically stops the lowering function “ON” position. (CE rated machines pull out before reaching the fully lowered position and sounds Emergency Stop Button located on Base an alarm. -
Page 18: Emergency Lowering System
Emergency Lowering System To Extend/Retract the Manual Extension Platform: Remove the locking pin(s) and push/ pull the extension deck using the sliding handrails or push-bar (Models 68XX). Reinsert the locking pin(s) upon full retraction or extension to prevent accidental movement of the extension platform. -
Page 19: Shutdown Procedure
Shutdown Procedure Warning DO NOT manually disengage the parking brakes if the Fully lower the platform. work platform is on a slope. Turn Key Switch to “OFF” position. Remove key. Make sure that the work platform is on level ground. Chock or block the wheels to keep work platform from Push in Emergency Stop Button. -
Page 20: Outrigger Operating Procedures
To turn off the inverter, push in the “EMERGENCY Raise the Platform: STOP” switch located on the operator’s control box 1- Ensure the emergency stop button is pulled to the open position, or slide the “ON/OFF” switch out. Select “LIFT” position with the Lift/Off/ located on the front face of the inverter to the “OFF”... -
Page 21: Battery Service And Charging Procedures
Battery Service And Charging Battery Charging Procedures Procedures Warning Battery Service Explosion Hazard Warning Chargers can ignite flammable materials and vapors. Explosion Hazard DO NOT use near fuels, grain dust, solvents or other flammable Keep flames and sparks away. DO NOT smoke near batteries. -
Page 22: Battery Charger Operation
Battery Charger Operation MAC Charger Operation (#BA1045) Bycan Charger Figure 2-15. Automatic SCR Battery Charger Green (COMPLETE) Green (80% COMPLETE) Figure 2-14. Bycan Battery Charger (4825U Shown) Green (INCOMPLETE) 1 Green LED Yellow (CHARGER ON) 2 Yellow LED 3 Red LED Yellow (ABNORMAL) Battery Status (SK4825U) This charger is equipped with an electronic circuit... -
Page 23: Mac Charger Operation (#Ba1001)
MAC #BA1045 continued... The function of the LED indicators is as follows: When the AC power is connected to the charger, the If the charger is restarted on a fully charged battery LED’s will flash several times then flash independently pack, the 80% and the “... - Page 24 Table 2-1. Owner’s Annual Inspection Record MODEL NUMBER________________________________ SERIAL NUMBER________________________ RECORDING DATE RECORDING YEAR # OWNER’S NAME INSPECTED Table 2-2. Maximum Platform Capacities (Evenly Distributed) With 3’ Extension Platform With 5’ Powered Extension Platform MODEL Main Platform Extension Platform Main Platform Extension Platform 900 lbs.
- Page 25 Table 2-3. Maintenance And Inspection Schedule Daily Weekly Monthly 3 Months 6 Months 12 Months* Mechanical Structural damage/welds Parking brake Tires/wheels & fasteners A, B & C A, B & C Guides/ rollers & slider pads A, B & I A, B &...
- Page 26 ELEVATING THE WORLD www.skyjackinc.com...
Need help?
Do you have a question about the SJIII 6826E and is the answer not in the manual?
Questions and answers