Subscribe to Our Youtube Channel
Related Manuals for Dynisco 1480
Summary of Contents for Dynisco 1480
- Page 1 From lab to production, providing a window into the process Dynisco 1480 1/8 DIN Indicator Concise Product Manual 59471-5 Operating Manual P/N: n/a Rev: n/a ECO: n/a www.dynisco.com...
-
Page 2: Installation
Replace the instrument by aligning the CPU and PSU boards with their guides in the housing, then slowly push the instrument back into position. NOTE: Option modules are automatically detected at power up. P/N: n/a Rev: n/a ECO: n/a www.dynisco.com... -
Page 3: Panel Mounting
NOTE: For an effective IP66 seal against dust and moisture, ensure gasket is well compressed against the panel, with the 4 tongues located in the same ratchet slot. P/N: n/a Rev: n/a ECO: n/a www.dynisco.com... - Page 4 FOR T/C INPUT) Use Screened Cable on Retransmission Option 1 Single Strand wire gauge: Max 1.2mm (18SWG) Connections This diagram shows all possible option combinations. The actual connections required depend on the options fitted. P/N: n/a Rev: n/a ECO: n/a www.dynisco.com...
-
Page 5: Select Mode
An unlock code is required to prevent unauthorised entry to Configuration, & Setup modes. Press to enter the unlock code, then press to proceed. NOTE: Automatic return to Operator Mode after 2 minutes without key activity. P/N: n/a Rev: n/a ECO: n/a www.dynisco.com... -
Page 6: Configuration Mode
, to return to Select mode. Note: Parameters displayed depends on how instrument has been configured. Refer to user guide (available from your supplier) for further details. Parameters marked * are repeated in Setup Mode. P/N: n/a Rev: n/a ECO: n/a www.dynisco.com... - Page 7 From lab to production, providing a window into the process P/N: n/a Rev: n/a ECO: n/a www.dynisco.com...
- Page 8 From lab to production, providing a window into the process P/N: n/a Rev: n/a ECO: n/a www.dynisco.com...
-
Page 9: Setup Mode
1 sec after, the parameter legend is shown, then the current value). Press to change the value. To exit from Setup mode, hold down and press to return to Select mode. Note: Parameters displayed depends on how instrument has been configured. P/N: n/a Rev: n/a ECO: n/a www.dynisco.com... - Page 10 From lab to production, providing a window into the process P/N: n/a Rev: n/a ECO: n/a www.dynisco.com -10-...
- Page 11 To exit from Calibration mode, hold down and press to return to Select mode. Note: Calibration mode will only be displayed if input type is set to St_G P/N: n/a Rev: n/a ECO: n/a www.dynisco.com -11-...
- Page 12 The message legend is shown for 1 second, followed by its value. Caution: Do not continue with the process until the issue is resolved. Note: CHHJ, CLLJ or OPEN may be displayed if an incorrect input type is selected. P/N: n/a Rev: n/a ECO: n/a www.dynisco.com -12-...
-
Page 13: Operator Mode
Note: All Operator Mode parameters in Display strategy 6 are read only (see diSP in configuration mode), they can only be adjusted via Setup mode. P/N: n/a Rev: n/a ECO: n/a www.dynisco.com -13-... -
Page 14: Alarm Indication
Logic Input, or by using the following key press sequence: Press until the process variable is displayed. Hold down together for three seconds until the display shows YES? P/N: n/a Rev: n/a ECO: n/a www.dynisco.com -14-... -
Page 15: Product Information Mode
(while this key is pressed, and for 1 sec after, the parameter legend is shown, followed by its value). Hold down and press to return to Select mode. Note: These parameters are all read only. P/N: n/a Rev: n/a ECO: n/a www.dynisco.com -15-... -
Page 16: Specifications
If Logic State setting in Config Mode = OPN, Reset or Tare occurs on a Closed to Open transition, or low (<0.8VDC) to high (3 to 5VDC)) transition. Isolation: No isolation from inputs and other outputs. P/N: n/a Rev: n/a ECO: n/a www.dynisco.com -16-... - Page 17 Depth Behind Panel: 100mm. Weight: 0.21kg maximum. MANUFACTURING SITE Address: The Hyde Business Park, Brighton, BN2 4JU, United Kingdom SYMBOL EXPLANATION Caution general danger to life General information and or limb notices. P/N: n/a Rev: n/a ECO: n/a www.dynisco.com -17-...
Need help?
Do you have a question about the 1480 and is the answer not in the manual?
Questions and answers