IBM Power System LC922 Quick Install Manual
Hide thumbs
Also See for Power System LC922:
- Quick install manual (20 pages) ,
- Quick install manual (12 pages) ,
- Servicing (158 pages)
Advertisement
Quick Links
IBM
Power System LC922
(9006-22C) Quick Install
IBM
Guide
®
IBM Power
System LC922 (9006-22C) Quick Install Guide
The IBM Knowledge Center is available online from: http://www.ibm.com/support/knowledgecenter/
POWER8/p8hdx/9006_22c_landing.htm.
v Read all precautions and instructions before you start working on key parts.
v Use normal electrostatic discharge (ESD) procedures when working on the system and parts. IBM
recommends wearing gloves and an anti-static wrist strap to avoid possible damage to the equipment.
9006-22C information: https://ibm.biz/9006-22CQR
9006-22C parts
Use this information to find the field-replaceable unit (FRU) part number.
After you identify the part number of the part that you want to order, go to Advanced Part Exchange
Warranty Service. Registration is required. If you are not able to identify the part number, go to
®
Contacting IBM
service and support.
Advertisement
Related Manuals for IBM Power System LC922
Summary of Contents for IBM Power System LC922
- Page 1 Read all precautions and instructions before you start working on key parts. v Use normal electrostatic discharge (ESD) procedures when working on the system and parts. IBM recommends wearing gloves and an anti-static wrist strap to avoid possible damage to the equipment.
- Page 2 Rack final assembly Figure 1. Rack final assembly Table 1. Rack final assembly part numbers Units per Index number Part number assembly Description MCP-290- Slide rail kit - contains left and right slide rails and 00057-0N attaching screws MCP-290- Slide rail kit - contains left and right slide rails and 00057-0N attaching screws...
-
Page 3: System Parts
System parts Figure 2. System parts... - Page 4 Table 2. System parts Index number Part number Units per assembly Description Top cover assembly Screws MCP-310-82914-0B CPU air baffle Heat sink kit (includes heat sink and thermal interface material) 16 core 2.9 GHz system processor module 20 core 2.9 GHz system processor module MEM-DR480L-049 8 GB, 2666 MHz 1RX4 DDR4 RDIMM* MEM-DR416L-066...
- Page 5 Table 2. System parts (continued) Index number Part number Units per assembly Description HDD-KIT-2A- 1.2 TB 10k (512 block size) 2.5 inch SAS disk drive ST1200S-IB001 HDD-KIT-2A- 1.8 TB 10k (512 block size) 2.5 inch SAS disk drive ST1800S-IB001 HDD-A2000- 2.0 TB 7.2K (512 block size) 3.5 inch SAS disk drive ST2000NM003401 or HDD-A2000-...
-
Page 6: Rear Ports
Table 2. System parts (continued) Index number Part number Units per assembly Description PWS-1K62A-1R Power supply RSC-R1UW-E8R- PCIe riser for PCIe adapter 4 (WIO-R Slot) IB001 PCI adapter. Use the feature type of the adapter to find the FRU number in PCIe adapter information by feature type for the 9006-22C GPU. -
Page 7: Installing And Removing
Figure 3. Rear ports Table 3. Input and output ports Identifier Description USB 2.0 used for keyboard and mouse. Certain USB drives might be too wide to fit properly into the USB ports on the rear of the system. Test the fit your USB drive before proceeding. - Page 8 Figure 6. Removing a front drive Figure 7. Removing the 3.5-inch drive from the tray Figure 8. Removing the 2.5-inch drive from the tray Figure 9. Removing the disk drive backplane and screws...
- Page 9 Figure 11. Removing a fan Figure 10. Removing the disk drive backplane cables Figure 13. Two processor memory plugging sequence Figure 12. Removing the memory Figure 14. 9006-22C PCIe adapter positions...
- Page 10 Figure 16. Removing a position 1 adapter from the riser Figure 15. Removing the PCIe riser Figure 17. Removing a position 2 adapter from the riser Figure 18. Removing position 1 riser card Figure 20. Removing the GPU from the riser Figure 19.
- Page 11 Figure 21. Removing position 3, 5, and 6 riser card Figure 22. Releasing the tail-stock Figure 23. Screw locations Figure 24. Lifting out the system backplane...
- Page 12 Figure 25. Loosening the load arm screw of the heat sink Figure 26. Lifting the heat sink from the load arm...
- Page 13 Figure 27. Placing the processor at an angle on the top cover of the packaging Figure 28. Installing the system processor module Figure 29. Installing the heat sink...
- Page 14 Figure 30. Tightening the load arm screw Figure 31. Time-of-day battery location...
- Page 15 This September 14, 2017 edition applies to IBM Power Systems servers that contain the POWER8 processor and to all associated models. © Copyright IBM Corporation 2017. US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract...