1. Manuals
  2. Brands
  3. Planet Manuals
  4. Network Storage Server
  5. NAS-7450
  6. Quick installation manual

Planet NAS-7450 Quick Installation Manual

Hide thumbs Also See for NAS-7450:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
NAS-7450/NAS-7850
Quick Installation Guide
Version 1.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NAS-7450 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Planet NAS-7450

Summary of Contents for Planet NAS-7450

  • Page 1 NAS-7450/NAS-7850 Quick Installation Guide Version 1.0...

  • Page 2: Table Of Contents

    1.3 NAS-7850 Package Content ..............5 1.4 Physical Detail ..................5 Chapter 2 Installing and Starting NAS system ............ 7 2.1 Installing the NAS-7450 / NAS-7850 rack-mount Model......7 2.2 Sliding Rails Installation ................. 9 Chapter 3 Basic Configuration .................15 3.1.

  • Page 3: Chapter 1 Package Contents

    Chapter 1 Package Contents 1.1 NAS-7450 Package Content NAS-7450 x 1 Key x 2 Power Cord x 1 Screw Package x 1 User’s Manual CD x 1 Quick Installation Guide x 1 Sliding Rail x 1 set If any of above items are damaged or missing, please contact your dealer immediately.
  • Page 4 Volume un-mounted and HDD is Red off Amber on ready for being hot-up plugged Disk faulty. Amber Blinks (Slowly) Blinking interval is about 2 seconds NAS-7450 Rear View e-SATA LAN Jack PCI-E Power Jack RS-232 Interface Description Connect the two power supply cord shipped with the...

  • Page 5: Nas-7850 Package Content

    1.3 NAS-7850 Package Content NAS-7850 x 1 Power Cord x 2 Screw Package x 1 User’s Manual CD x 1 Quick Installation Guide x 1 Sliding Rail x 1 set If any of above items are damaged or missing, please contact your dealer immediately.
  • Page 6 HDD Access LED HDD ready LED Description Red on during Green Blinks Power is being accessed access RAID building, rebuilding, Red on Green Blinks (FAST) expending Volume un-mounted and HDD is Amber on ready for being hot-unplugged Disk fault Blinking interval is 2 Amber Blink (Slowly) second Hard disk is absent or SATA...

  • Page 7: Chapter 2 Installing And Starting Nas System

    Chapter 2 Installing and Starting NAS system This chapter covers the installation procedure of different form factors of NAS server as well as the NAS-7450 / NAS-7850 Mobile Rack. Instruction on how to startup the NAS server by setting up the basic configuration through the Admin Home page or provided software tool –...
  • Page 8 Then, push the level down as far as it can go to connect the hot swap hard disk tray to the chassis. Figure 3 NAS-7450 / NAS-7850 rack-mount server installation 1. Pull out a HDD tray from the server. 2. Secure and mount a hard disk onto the HDD tray using four screws under the tray.

  • Page 9: Sliding Rails Installation

    7. Connect your NAS server to the network by attach a LAN cable from the LAN port located at the back of your NAS server.(At least one network connection is required) 8. Plug the power cord into the power connector on you NAS server. 9.
  • Page 10 3. Now install the center slide to the rack-mount chassis. Find the screw holes on both sides of the rack-mount chassis, which are used for mounting the center slide. Fasten the “#6-32” screws to fix the center slides onto chassis. Later, the center slides will be used for attaching to the sliding rail.
  • Page 11 Configuring the NAS using the LCD console LCD menu console flow chart System Ready Enter Configure LAN1 LAN1 mask: LAN1 gateway: LAN1 IP: Configure LAN1? IP/Mask/Gateway 255.255.0.0 192.168.1.254 192.168.0.100 Yes/No Enter Configure LAN2 LAN2 mask: LAN1 gateway: LAN1 IP: Configure LAN2? IP/Mask/Gateway 255.255.0.0 192.168.1.254...
  • Page 12 Configuring the IP addresses using the LCD console 1. After NAS server is boot up, the LCD console shows System Ready. Press the right button. 2. The IP address of LAN1 is shown. Press the middle button to configure LAN1 IP ...
  • Page 13 8. Repeat the above process to configure the other LAN port. Configuring the IP addresses using NAS Finder You can use the provided utility PLANET NAS Finder to perform the initial setup of your newly arrived NAS server. The utility designed to perform a quick set up and put your NAS server online in just a few minutes.
  • Page 14 1. Highlight the server you want to configure from the left hand pane. 2. Click the button on the toolbar 3. Or, right click the server and select “Configure” 4. Enter the “Server Name”, “Server Comment”, and “Workgroup/Domain Name” and select either the “Workgroup mode” or “Domain mode”. 5.

  • Page 15: Chapter 3 Basic Configuration

    Chapter 3 Basic Configuration 3.1. Web configuration access The NAS-7450 / NAS-7850 provide GUI (Web based, Graphical User Interface) for management and administration. The default IP address of NAS server is 192.168.0.100. You may now open your web browser, and insert http://192.168.0.100 in the address bar of your web browser to login web configuration page.

  • Page 16: Hdd Formation And Raid Setting

    3. After format completed, you can then start to access the storage of the RAID NAS server accordingly. Further Information This guide is used to help you startup your NAS-7450 / NAS-7850 settings. It is also recommended to check the user manual CD-ROM for more details of the system and user configuration.

This manual is also suitable for:

Nas-7850

Table of Contents