Table of Contents
Related Manuals for CRYSTAL GROUP INC. RS232S13
Summary of Contents for CRYSTAL GROUP INC. RS232S13
- Page 1 RS232S13/17 Rugged Server User Guide The most trusted provider of computer architecture for operational, deployable, and high reliability applications. ISO 9001:2008 & CRYSTAL GROUP INC. AS9100C:2009 CERTIFIED QMS DOC-00155 REV. E...
-
Page 2: Table Of Contents
C. INSTALLING THE PRODUCT GROUNDING RACK MOUNTING PRECAUTIONS INSTALLING IN AN EQUIPMENT RACK D. OPERATING THE PRODUCT CONNECTING TO THE POWER SOURCE POWERING THE SERVER ON E. MAINTAINING THE PRODUCT DRIVER UPDATES CHASSIS ACCESS RS232S13/17 Rugged Server User Guide Page 1 of 24... - Page 3 EXPANSION/RISER CARD REMOVAL AND REPLACEMENT HARD DRIVE REMOVAL AND REPLACEMENT MEMORY REMOVAL AND REPLACEMENT F. TROUBLESHOOTING AVAILABLE WARRANTY CRYSTAL GROUP LIMITED WARRANTY LEGAL INFORMATION COPYRIGHTS AND TRADEMARKS DISCLAIMERS CERTIFICATIONS AND LICENSES RS232S13/17 Rugged Server User Guide Page 2 of 24...
-
Page 4: Thank You
RS232S13/17 Rugged Server We Thank You! From all of us at Crystal Group Inc., THANK YOU for your purchase of the RS232S13/17 Rugged Server Our customers are the lifeline that keeps Crystal going. That is why it is extremely important to us that our customers are 100% satisfied with their product choice. -
Page 5: Safety
A note indicates important information that helps make better use of the equipment. WARNING A warning indicates a potential for property damage, personal injury, or death. CAUTION Caution indicates potential damage to hardware or loss of data if instructions are not followed. RS232S13/17 Rugged Server User Guide Page 4 of 24... -
Page 6: Handling Precautions
The following applies to any battery that might be on any board installed in the equipment: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the instructions. RS232S13/17 Rugged Server User Guide Page 5 of 24... -
Page 7: Contact Information
After hours messaging service is available with a less than 30-minutes response time. Within the United States: 800-378-1636 International Number: 1+319-378-1636 Email Address: support@crystalrugged.com Request a Form Under Tech Support: http://www.crystalrugged.com For Up-to-the-minute Crystal Products Information visit our website at: http://www.crystalrugged.com RS232S13/17 Rugged Server User Guide Page 6 of 24... -
Page 8: Product Information
RS232S13/17 Rugged Server Product Information OVERVIEW The Crystal RS232S13/17 is a compact two rack unit (R/U) server in a 3.5" (2U) high by wide by depth chassis that can be rack mounted or used as a stand-alone unit. The RS232S13/17 consists of an aluminum chassis/enclosure, a power supply, and an ATX form-factor motherboard. - Page 9 Option 3 Jonathan rails Power Supply Options Option 1 (standard) The RS232S13/17 is available with a 400 or 460 Watt full range ATX power supply with the following specifications: Input Voltage: 120 to 240 VAC w/PFC full range Frequency: 50-400Hz.
- Page 10 Commercial Standards Commercial standards are based on the National Electric Code (NFPA70- National Fire Protection Association). Please visit the following link to learn more about the National Electric Code standards: http://www.nfpa.org RS232S13/17 Rugged Server User Guide Page 9 of 24...
-
Page 11: Installing The Product
RS232S13/17 Rugged Server Installing the Product GROUNDING AC Version- to ensure a good earth ground, the RS232S13/17 should be used with a UL listed three-conductor power cord connected to a three-conductor grounded power source. DC Version- input installations- use only approved copper connectors. - Page 12 RS232S13/17 Rugged Server INSTALLING THE RS232S13/17 WITH CRYSTAL SLIDES IN AN EQUIPMENT RACK To install RS232S13/17 with crystal slides in an equipment rack, complete the steps and below: Figure 1 Line up two holes on the front mounting ears at the desired level on the front of the equipment rack, and attach to the rack using (2) 10-32 x rack screws provided.
-
Page 13: Operating The Product
RS232S13/17 Rugged Server Operating the Product If the RS232S13/17 is part of a rack configuration, refer to the rack guide for more information on connecting to a power source. CONNECTING TO A POWER SOURCE Please see Section C- Installing the Product for more information. - Page 14 RS232S13/17 Rugged Server CHASSIS VIEWS: Figure 2. Front View RS232S13/17 Figure 3. Rear View RS232S13/17 The images above may not depict the product received. RS232S13/17 Rugged Server User Guide Page 13 of 24...
- Page 15 COM Port 1 (Turquoise) LAN Port 2 VGA (Blue) Side_Surround (Grey) Gigabit LAN 1 Back_Surround (Black) Gigabit LAN 2 CEN/LFE (Orange) Microphone-In (Pink) Front (Green) Line-In (Blue) Figure 4. I/O Ports RS232S13/17 Rugged Server User Guide Page 14 of 24...
- Page 16 Gb LAN Port 2 SPDIF Out Surround Out Center/LFE Out Mic In Line Out Line In . I/O Ports Figure 4 The product received will have one of the four I/O ports shown above. RS232S13/17 Rugged Server User Guide Page 15 of 24...
-
Page 17: Expansion/Riser Card Removal And Replacement
With the expansion card in place within the slot, install the screw and tighten to hold the card in place. Re-attach card cage assembly to chassis with the three screws. RS232S13/17 Rugged Server User Guide Page 16 of 24... - Page 18 Attach appropriate connectors. Replace chassis cover. Figure 5. Expansion/Riser Card Installation The image above may not depict the product received. RS232S13/17 Rugged Server User Guide Page 17 of 24...
-
Page 19: Hard Drive Removal And Replacement
Tighten thumbscrews to secure the drive. Reapply power to the server, rebuilding any RAID arrays as necessary. Figure 6. Drive Removal and Replacement The image above may not depict the product received. RS232S13/17 Rugged Server User Guide Page 18 of 24... -
Page 20: Memory Removal And Replacement
Press the DIMM into its slot evenly on both ends until it clicks into place. The DIMM release levers will snap into place. The DIMM is properly seated when the release levers have fully engaged. RS232S13/17 Rugged Server User Guide Page 19 of 24... - Page 21 RS232S13/17 Rugged Server USB2 Figure 7. Installing DIMM RS232S13/17 Rugged Server User Guide Page 20 of 24...
-
Page 22: Troubleshooting
6. Before calling, please have the following information available to help expedite assistance: Unit serial number Brief description of the problem Brief explanation of the steps already taken to isolate and resolve the problem RS232S13/17 Rugged Server User Guide Page 21 of 24... -
Page 23: Available Warranty
LIABILITY IN TORT, OR PRODUCT LIABILITY, ANY DELAY IN MANUFACTURE OR DELIVERY OF EQUIPMENT OR PRODUCT, OR FOR ANY FAILURE OF SELLER TO COMPLY WITH THIS AGREEMENT SHALL BE THE REPAIR OR REPLACEMENT OF THE PRODUCTS AS PROVIDED HEREIN. (REVISED DECEMBER RS232S13/17 Rugged Server User Guide Page 22 of 24... -
Page 24: Legal Information
Crystal and the Crystal Logo are trademarks of Crystal Group Inc. or its affiliates in the U.S. and other countries. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Crystal and any other company. RS232S13/17 Rugged Server User Guide Page 23 of 24... -
Page 25: Copyrights And Trademarks
SYMBOLS THAT APPLY. IF THERE ARE ANY QUESTIONS ABOUT THE LICENSES AND/OR CERTIFICATIONS THAT CRYSTAL OBTAINS, PLEASE CONTACT A CRYSTAL REPRESENTATIVE AT ONE OF THE OPTIONS LISTED ON THE CONTACT INFORMATION SECTION LOCATED ON PAGE 6. THANK YOU FOR YOUR BUSINESS. RS232S13/17 Rugged Server User Guide Page 24 of 24...
Need help?
Do you have a question about the RS232S13 and is the answer not in the manual?
Questions and answers