Laser Pegs RUNNERS 1320 B Manual

Please read manual before you begin! Failure to
1320 B
follow this manual's instructions may result in
damage to the Power Base and/or Laser Pegs®.
Not adhering to these directions will void the
RUNNERS™
manufacturer's warranty. Packing has to be kept
since it contains important information.
For Boys And Girls
Ages 5 And Up WARNING:
CHOKING HAZARD
6 Models+
- Small parts.
Not for children under 3 yrs.
Any creation you can build Do not submerge in water.
LIGHTED
CONSTRUCTION SET INCLUDES:
• 2 Laser Pegs®
• 24 Construction Parts
• Runner Power Base
• Instruction Manual Construction Compatible
Compatible with other construction kits
Requires 3 AAA Batteries
Batteries NOT
EN71, RoHS COMPLIANT
Included
This product complies to
all safety requirements
of ASTM F 963
MODEL INSTRUCTIONS
All additional model instructions can
be downloaded at www.LaserPegs.com
Laser Pegs® Parts List
There is No LED In The 90 Degree Peg
x2
SQUARE
PEG
TANK RUNNERS™ Power Base
Laser Pegs Stackable
®
Allows you to connect to
Laser Pegs
® link that
both Laser Pegs® and other
allows you to connect to
construction kits.
other construction kits.
Each Laser Peg® is color coded on the circuit board inside
Color
Code each shape. There is No LED In The 90 Degree Peg.
Construction Parts List
x1
x2
x2
x1
x4
x3
www.LaserPegs.com
This manual is copyright and cannot be reproduced or used online without Laser
Pegs®Ventures LLC permission. Copyright 2013 © All Rights Reserved US Patent
#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs® Ventures
LLC. 8304 Consumer Ct., Sarasota FL 34240. Contact: Support@LaserPegs.com
Connecting Pegs
To construct with Laser Pegs®, slide two pieces together to form a connection.
Slide each piece on and off smoothly. The 90° pegs are essential to construction
but they DO NOT ILLUMINATE.
RUNNERS™ POWER BASE
The Laser Pegs® Runners™ power base allows you to build with Laser Pegs® and
construction parts to form models. It is battery operated to run on its own.
Peg Holes Construction Part Connection
Allows you to construct Allows you to connect to other
with Laser Pegs®.
Hitch
Power
Button
Switch power button to
cycle through the Runners™
power settings.
LIGHT/OFF/ON/FLASH
Hitch
POWER SETTINGS
LIGHT - Illuminates your model
OFF - Turns power off
ON - Turns on motion and light
x4
FLASH - Light Flash with motion
x2
*If your speed setting is in neutral the Runners™ will not run by itself.
Once you have switched the speed setting to either medium or fast
the motor will engage.
x5
WARNING! Each Laser Peg® draws current from the batteries. Therefore, the more
pegs you use, the quicker you will deplete your battery power! As the power
weakens, the current will slowly fail and some Laser Pegs® will illuminate (typically
the reds and yellows) and some won't. When the Laser Pegs® dim the Laser Pegs®
are not broken, they just need stronger batteries.
You have 2 simple options...
1. Change the batteries.
2. Use high quality batteries. They will last a little longer, but they will still deplete
rapidly the more laser pegs you connect!
When Using Batteries
1. Remove screws.
2. Place three AAA batteries in the correct
position - as displayed inside the Runners™
Power Base.
3. Switch power button setting to
light/on/flash
4. Switch speed setting to engage motor.
5. Do not mix old and new batteries.
6. Do not mix alkaline, standard (carbon-
zinc), or rechargeable (nickel-cadmium)
batteries!
7. Exhausted batteries are to be removed
from the power base.
8. Never connect more than 20 Laser Pegs®
9. Non-rechargeable batteries are not to be
recharged.
10. Rechargeable batteries are only to be
charged under adult supervision.
11. Rechargeable batteries are to be removed
from the toy before being charged.
12. Batteries are to be inserted with the
correct polarity.
13. The supply terminals are not to be short-
circuited.
construction kits.
Speed
Connecting Laser Pegs® to RUNNERS™ POWER BASE
Settings*
Battery
Compartment
Requires (3AAA) Batteries
SPEED SETTINGS
Speed
Settings*
MEDIUM
Push Switch
Remove the Philips
head screw with a
4mm screw driver.
Requires (3AAA) Batteries
The Runners™ power base will not operate on its own if the speed setting is in neutral.
NEUTRAL
Push Switch
(CENTER)
Screw
Requires (3AAA) Batteries
AVOID DAMAGE TO PEG HOLES
*To avoid short-circuits, keep metal objects and
other un-authorized materials from obstructing
the peg holes.
Never connect more than 20
pegs at one time.
FAST
Push Switch