Page 2
Repairs to or replacement of the TEMPUR Ergo System or its components under the terms of this limited warranty will apply to the original warranty period and will not serve to extend such period. The decision to repair or to replace defective parts under this warranty shall be made, or case to be made, by Tempur-Pedic at its option and in its sole discretion.
TEMPUR ERGO System ® ™ Table of Contents SAFETY PRECAUTIONS ....................4 COMMONLY ASKED QUESTIONS AND ANSWERS ............ 8 SPECIFICATIONS......................9 INSTALLATION ......................10 OPERATION WIRED REMOTE CONTROL FEATURES .............. 18 TROUBLESHOOTING ....................19 SERIAL NUMBER: Customer Service: 1–800–979–1457...
TEMPUR ERGO System ® ™ SAFETY PRECAUTIONS WARNING! • Keep the cord away from heated surfaces. • Never operate the furnishing with the air openings blocked. IMPORTANT SAFETY Keep the air openings free of lint, hair and the like. • Never drop or insert any object into any opening. INSTRUCTIONS.
Page 5
Safety Precautions GROUNDING SAFETY WARRANTY PRECAUTION! Do not open control box, motors or wired remote This product is for use on a nominal 120-volt circuit, and control. The warranty is void if these units are tampered has a grounding plug that looks like the plug illustrated in sketch A (see Figure).
TEMPUR ERGO System ® ™ IMPORTANT SAFETY FEATURES USER-SERVICEABLE PARTS Use this furnishing only for its intended use as described This product is specifically designed to have no in these instructions. Do not use attachments not maintenance by you, the user. Therefore, you are recommended by the manufacturer.
Page 7
Safety Precautions PRODUCT RATINGS INTENDED USAGE The lift motors in your Ergo System are NOT designed for The electric adjustable bed should be installed with the head board bracket and/or the head of the continuous use. Reliable operation and full life expectancy frame should be positioned close to a wall.
WHAT IS THE LIFT CAPACITY OF THE ERGO SYSTEM? With standard legs and casters installed, the overall Please see the chart below for Tempur-Pedic’s height is approximately 15" from the floor to the recommended and approved “total people weight” limits bottom of the mattress.
Q&A / Specifications Bed Type A. Frame B. Base C. Base Weight width Width Length Specifications Twin Long 30" 37 1/2" 79" 128 lbs. Queen 40" 58 1/2" 79" 167 lbs. Split CA King 30" 35 3/4" 83" 115 lbs. 38 1/10"...
TEMPUR ERGO System ® ™ Installation Instructions Before discarding any packing materials, check your TEMPUR Ergo System carton and verify the following ® ™ items in the parts list are included: PARTS LIST A. Wired Remote Control – hardwired to bed (1)* B.
Page 11
Installation STEP 1 STEP 3 Carefully lift your Ergo System out of the shipping Remove and extend the power cord and wired carton, keeping the unit top side down. For safety remote from the frame. reasons, this should be performed by 2 people. WARNING! POWER CORDS AND WIRED CORDS MUST NOT INTERFERE WITH ANY ERGO SYSTEM MECHANISMS.
Page 12
Flat button until the Ergo System base returns to the flat position. NOTE: If the Ergo System is to be set up without a headboard, simply place your Tempur-Pedic mattress onto the frame. Installation is now complete. If a headboard is to be installed, proceed to the next page.
Page 13
Installation HEADBOARD INSTALLATION NOTE: This step is only needed if installing a STEP 1 headboard with optional brackets available Assemble the Headboard Bracket: separately. STEP 1A NOTE: Failure to follow the proper headboard Use the remote to raise the head of the bed in order bracket installation instructions may result in to gain access to the Ergo System frame.
Page 14
TEMPUR ERGO System ® ™ STEP 1C Place Bracket Bolts (D) with a 5/16 inch washer (F) Place the open side of the the Inner Headboard Bracket through the Outer Headboard Bracket (C) and into (B) into the open side of the Leg Clamp Bracket (A). the Inner Headboard Bracket (B).
Page 15
Installation STEP 2 STEP 3 Attach your headboard to the Headboard Brackets Place your Tempur-Pedic mattress on top of your Ergo following the steps below: System Base. STEP 2A Measure the center-to-center distance of the mounting holes in your headboard.
Page 16
TEMPUR ERGO System ® ™ Pairing Instructions For Joining Two Bases FOR 2 BASES TO OPERATE WITH 1 CONTROL STEP 5 Remove the hardwired remote controls and set aside. Place the spare remote control in a safe place for any Assembling Split Dual Ergo Bases (Base A and Base B) to future use.
TEMPUR ERGO System ® ™ Wired Remote Control Features READ ADVISORY INFORMATION IN THE SAFETY PRECAUTIONS SECTION OF THIS GUIDE CAREFULLY BEFORE USING THIS PRODUCT. THE POTENTIAL FOR ELECTRIC SHOCK EXISTS IF ELECTRICAL COMPONENTS ARE NOT INSTALLED OR OPERATED PROPERLY. LED SIGNATURE LIGHT A.
Operation / Troubleshooting Troubleshooting In the event that your TEMPUR ® Ergo System ™ fails to operate properly, investigate the symptoms and possible solutions provided in the chart below: SYMPTOM SOLUTION • Verify that the power cord is plugged into a working, grounded electrical outlet.
Page 20
TEMPUR ERGO System ® ™ FOR TECHNICAL SUPPORT OR SERVICE, PLEASE CHOOSE FROM THE FOLLOWING NUMBERS: QUESTIONS ABOUT YOUR ERGO SYSTEM BASE: 1-800-979-1457 QUESTIONS ABOUT YOUR TEMPUR-PEDIC MATTRESS OR TO ORDER ERGO SYSTEM ACCESSORIES: 1-800-821-6621 OR VISIT WWW.TEMPURPEDIC.COM...
Need help?
Do you have a question about the TEMPUR-Ergo System and is the answer not in the manual?
Questions and answers