Page 1
Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide October, 2014 Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices. Text Part Number: OL-32138-01...
Page 2
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.
Radios Power Sources Power-over-Cable AC Power Supply DC Interface PoE-Input Optional Hardware Network Deployment Examples 1-10 Wireless Backhaul 1-10 Point-to-Point Bridging 1-10 Point-to-Multipoint Bridging 1-11 Point-to-Multipoint Mesh Network 1-13 Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 4
2-25 Installing a Lightning Arrestor 2-25 Installation Considerations 2-26 Installation Notes 2-26 Installing the Lightning Arrestor Outdoors 2-26 Cable for the Lightning Arrestor 2-27 Grounding the Access Point 2-27 Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 5
European Community, Switzerland, Norway, Iceland, and Liechtenstein Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC Declaration of Conformity for RF Exposure United States Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 6
Configuring Option 43 for 1000, 1500, and 1570 Series Access Points Configuring Option 43 for 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1570 Series Access Points L O S S A R Y Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Series Outdoor Access Point Hardware Installation Guide. Objectives This publication explains the steps for installing the Cisco Aironet 1570 Series Outdoor Access Point (called the access point, or abbreviated as AP in this document). The access point is available in an internal antenna model with cable modem (AIR-AP1572IC), an external antenna AC model (AIR-AP1572EAC) and an external antenna model with cable modem (AIR-AP1572EC).
Information you must enter is in boldface screen boldface screen font font. Arguments for which you supply values are in italic screen font italic screen font. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide viii OL-32138-01...
Page 9
Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen. BEWAAR DEZE INSTRUCTIES Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 10
å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. TA VARE PÅ DISSE INSTRUKSJONENE Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 11
Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Figyelem Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 12
Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 13
Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide xiii OL-32138-01...
Click this link to browse to the Cisco Wireless documentation home page: http://www.cisco.com/en/US/products/hw/wireless/index.html To browse to the access point documentation, click Cisco Aironet 1570 Series listed under “Outdoor Wireless.” The documentation can be accessed from the Support box. To browse to the Cisco Wireless LAN Controller documentation, click Standalone Controllers listed under “Wireless LAN Controllers.”...
Access point MAC address, for example 68BDABF54600 (12 hexadecimal digits). It is located • under the serial number. You need your product serial number when requesting support from the Cisco Technical Assistance Center. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide...
Obtaining Documentation, Support, and Security Guidelines For information on obtaining documentation and support, providing documentation feedback, security guidelines, and recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html...
About the Access Point The Cisco Aironet 1570 Series Outdoor Access Point (hereafter called the access point or AP) is a high performance outdoor access point designed for service in outdoor and mesh networks. All versions of the access point have simultaneous dual-band radio consisting of an 802.11ac Wave 1 4x4:3 5 GHz radio and 4x4:3 802.11n 2.4 GHz radio.
A-, B-, C-, D-, E-, F-, H-, K-, M-, N-, Q-, R-, S-, T-, Z- – Click this URL to browse to a list of countries and regulatory domains supported by the 1570: www.cisco.com/go/aironet/compliance Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Sniffer mode • Mesh modes: • FlexConnect over Mesh – Meshing to other Cisco Aironet access points, such as the 1550 series, 1530 series, and also – Cisco Aironet indoor mesh access points. Backhaul on 2.4 GHz link. – Bridging: •...
Cisco does not recommend any third-party antennas, and Cisco Technical Assistance Center will not be able to provide any support for third-party antennas. Cisco’s FCC Part 15 compliance is only guaranteed with Cisco antennas or antennas that are of the same design and gain as Cisco antennas.
U.S.: NFPA 70, National Electric Code, Article 180, Canada: Canadian Electrical Code, Section 54). Statement 1052 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 366 Do not work on the system or connect or disconnect cables during periods of lightning activity. Warning Statement 1001 Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
AP to prevent damage to the AP or to the cable plant. Fuses of various amperage are available, and so you can select the appropriate fuse rating depending on the configuration and operating voltage. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Depending on what you ordered, the following optional access point hardware may be part of your shipment: External antennas, depending on which ones you purchased • Power injector AIR-PWRINJ1500-2 • • AP cover / Solar Shield Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 25
• GPS antenna • Strand Mount kits • Pole Mount kit • Pedestal Mount kit • Spare Parts kit containing extra cable glands, power connector, ground lug, etc. • Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Figure 1-2. To support Ethernet bridging, you must enable bridging on the controller for each access point. By default this capability is turned-off for all access points. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 1-10 OL-32138-01...
2.4-GHz wireless coverage area may be limited and possibly not suitable for direct wireless client access. Figure 1-4 illustrates an example of access point-to-multipoint bridging. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 1-11 OL-32138-01...
Page 28
2.4 or 5 GHz radio, but not both. In this mode, one access point is designated as the root and the other end is designated as the non-root bridge. Figure 1-5 Access Point to Multipoint Bridging in Autonomous Mode Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 1-12 OL-32138-01...
• Powering the Access Point, page 2-28 • Powering the Access Point, page 2-28 • Configuring the Access Point, page 2-39 • What to Do Next, page 2-40 • Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Wall/Pole mount bracket with tilt mechanism, spare only (AIR-ACC1570-PMK2=) AC/DC power adapter, spare only (AIR-PWRADPT-1570=) • Spare Parts kit containing extra cable glands, power connector, ground lug, etc. • (AIR-ACC1570-KIT1=) FIPS kit (AIRLAP-FIPSKIT=) • Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
• Warnings Translated versions of all safety warnings are available in the safety warning document that shipped with your access point or on Cisco.com. To browse to the document on Cisco.com, refer to Appendix A, “Translated Safety Warnings” for instructions.
FCC-certified equipment. When used with approved Cisco Aironet antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper operation of this radio device according to the instructions in this publication results in user exposure substantially below the FCC recommended limits.
Page 35
Do dress properly—shoes with rubber soles and heels, rubber gloves, long sleeved shirt or – jacket. Use a rope to lift the access point. If the assembly starts to drop, get away from it and let it fall. • Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Because the access point is a radio device, it is susceptible to common causes of interference that can reduce throughput and range. Follow these basic guidelines to ensure the best possible performance: For information on planning and initially configuring your Cisco Mesh network, refer to the Cisco •...
What is the minimum acceptable data rate within the link? • Do you have the correct antenna (if more than one antenna is being offered?) • Do you have access to both of the mesh site locations? • Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
“Configuring DHCP Option 43” section on page F-1). Become familiar with the access point installation components (see the “Becoming Familiar with • Access Point Installation Components” section on page 2-12). Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Installing the Access Point Installation Guidelines Becoming Familiar with the Access Point Versions Figure 2-1 1570I Series AP Top-Front Three Quarter View Figure 2-2 1570I Series AP Front-Bottom Three Quarter View Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 40
Chapter 2 Installing the Access Point Installation Guidelines Figure 2-3 1570E Series AP Front View Figure 2-4 1570E Series AP Top-Front Three Quarter View Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-10 OL-32138-01...
Page 41
Chapter 2 Installing the Access Point Installation Guidelines Figure 2-5 1570E Series AP Front-Bottom Three Quarter View Figure 2-6 1570E Series AP with AC Port Top-Front Three Quarter View Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-11 OL-32138-01...
The 1570 Series Access Point can be strand, pole or pedestal mounted. All installation methods for mounting an access point on any wall surface is subject to the acceptance of Caution local jurisdiction. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-12 OL-32138-01...
You must also ensure the access point is mounted in such a way as to ensure that all antenna ports and the console port are accessible for future use. Note Omnidirectional antennas are vertically polarized and should be mounted vertically. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-13 OL-32138-01...
Use the mounting bracket as a template to mark four screw hole locations on the mounting surface. Step 1 Figure 2-8 for the mounting bracket screw hole locations. Use the mounting slotted holes to attach the unit to the wall. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-14 OL-32138-01...
Page 45
Note If necessary, use suitable screw anchors and an exterior-grade plywood backboard to mount the access point to stucco, cement or drywall. Figure 2-9 Mounting Bracket Dimensions Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-15 OL-32138-01...
Wrap the band clamps around the pole and slide them into the second set of top and bottom mounting Step 3 slots on the bracket. Lightly tighten the clamps. Only tighten them enough to keep the bracket from sliding down the pole. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-16 OL-32138-01...
For installation instructions and detailed information on these antennas, refer to the appropriate document located at: http://www.cisco.com/en/US/products/hw/wireless/ps469/prod_installation_guides_list.html Follow all safety precautions when installing the antennas. For information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-18. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-17 OL-32138-01...
Cisco does not recommend any third-party antennas, and Cisco Technical Assistance Center will not be able to provide any support for third-party antennas. Cisco’s FCC Part 15 compliance is only guaranteed with Cisco antennas or antennas that are of the same design and gain as Cisco antennas.
Cisco Aironet Dual-Band Omnidirectional Antenna (AIR-ANT2547V-N, AIR-ANT2547VG-N) The Dual-Band Omnidirectional Antenna, referred to as a “stick” antenna, is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz and 5-GHz frequency bands (Figure 2-16).
Page 50
Installing Antennas Figure 2-10 Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna - Installed Only on Model AIR-CAP1572E-x-K9 When installing the AIR-ANT2588P3M-N with the Cisco Aironet 1570 Series AP, connect the Note outermost antenna ports (marked ‘1’ in Figure 2-11) to the AP’s dual band antenna ports.
Page 51
Installing Antennas Cisco Aironet 5-GHz 14-dBi 2-Port Directional Antenna (AIR-ANT5114P2M-N) The Cisco Aironet 5-GHz 14-dBi 2-Port Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 5-GHz frequency band. This antenna has 14-dBi in the 5-GHz band.
Page 52
Installing Antennas Cisco Aironet 2.4-GHz 13-dBi 2-Port Directional Antenna (AIR-ANT2413P2M-N) The Cisco Aironet 2.4-GHz 13-dBi 2-Port Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has 13-dBi gain in the 2.4-GHz frequency band.
Page 53
Installing Antennas Cisco Aironet 2.4-GHz 5-dBi Omnidirectional Antenna (AIR-ANT2450V-N) The Cisco Aironet 2.4-GHz 5-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has a 5-dBi gain in the 2.4-GHz band.
Page 54
Installing Antennas Cisco Aironet 2.4-GHz 8-dBi Omnidirectional Antenna (AIR-ANT2480V-N) The Cisco Aironet 2.4-GHz 8-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has 8-dBi gain in the 2.4-GHz frequency band.
Installing Antennas Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna (AIR-ANT5180V-N) The Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 5-GHz frequency band. This antenna has 8-dBi gain in the 5-GHz frequency band.
Installing Antennas Installation Considerations Cisco recommends that you bulkhead mount the lightning arrestor so it can be installed as a wall-feed through on the wall of the protected space. The importance of obtaining a good ground and bonding connection cannot be overstressed. Consider these points when grounding the lightning arrestor: Connect the lightning arrestor components directly to the grounding point.
(the longer the run, the greater the loss). Cisco recommends a high-quality, low-loss cable for use with the lightning arrestor. Grounding the Access Point The access point must be grounded before connecting power.
PoE+ (802.3at power) switch port or the AIR-PWRINJ4= power injector, then the access point will automatically disable one of the 2.4 GHz transmitters and the radio will operate in 2x3 MIMO mode. Table 2-4 AP 1570 Power Matrix Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-28 OL-32138-01...
Connect a CAT5e or better Ethernet cable from your wired LAN network to the power injector. Step 3 Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-29 OL-32138-01...
To forward bridge traffic, add a switch between the power injector and controller. Refer to the Cisco Wireless Mesh Access Points, Design and Deployment Guide, Release 7.0 for more information.
Page 61
2-19. Step 7 Carefully insert the RJ-45 cable connector into the Ethernet port opening on the access point, and connect to the internal Ethernet connector (see Figure 2-19). Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-31 OL-32138-01...
The power should not be removed by disconnecting the DC power connector on the unit. A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Warning Statement 1022 Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-32 OL-32138-01...
Page 63
Verify that the cable gland has a rubber seal and ensure that it is not damaged. Note Failure to install the Cable Gland properly will cause the cable grip to leak. Warning Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-33 OL-32138-01...
Page 64
(9.5 mm) from each wire. Step 7 Insert each wire into the two-position terminal strip (supplied), and tighten each wire using a 0.1 inch (0.25 cm) flat screw driver (see Figure 2-21). Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-34 OL-32138-01...
Page 65
(see Figure 2-22). Note Ensure that the polarity of the terminal strip properly matches the polarity markings on the enclosure (see Figure 2-23) Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-35 OL-32138-01...
Page 66
Ensure that the antennas are connected to the access point before you apply power to the access point. Step 12 Turn on the DC power at the designated circuits. Step 13 Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-36 OL-32138-01...
For your safety, when connecting the access point AC power connector, always connect the access point Caution end of the cable FIRST. When removing the AC power connector, always disconnect the access point end of the cable LAST. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-37 OL-32138-01...
Warning Warning Follow all local wiring and electrical codes when making this connection. Note that the spliced cables may need to be housed in an approved junction box. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 2-38 OL-32138-01...
For Lightweight Access Points and Mesh Access Points, see the Cisco Wireless LAN Controller • Configuration Guide, which is available at: http://www.cisco.com/en/US/docs/wireless/controller/7.6/configuration/guide/b_cg76.html For Mesh Access Points, see the Cisco Wireless Mesh Access Points, Design and Deployment Guide, • which is available at: http://www.cisco.com/en/US/docs/wireless/technology/mesh/7.6/design/guide/mesh76.html For Access Points in autonomous mode, see the Cisco Aironet Access Points Configuration Guide •...
When you power up a MAP that is not connected to a wired Ethernet, fiber-optic, or cable network to the controller, the access point uses the Cisco Adaptive Wireless Path Protocol (AWPP) to bind to another mesh access point (MAP) with the best path to a root access point (RAP) connected to the wired network to a controller.
Page 71
C H A P T E R Troubleshooting This chapter provides troubleshooting procedures for basic problems with the access point. For the most up-to-date, detailed troubleshooting information, refer to the Cisco Technical Support and Documentation website at the following URL: http://www.cisco.com/cisco/web/support/index.html...
Option 43 provides the IP addresses of the management interfaces of your controllers. Typically, a DHCP server can be configured on a Cisco switch. Optionally, a DNS server can be configured to enable CISCO-CAPWAP-CONTROLLER. Use – local domain to resolve to the IP address of the management interface of your controller.
Refer to the product documentation for your DHCP server for instructions on configuring DHCP Option 43. For additional information, refer to the “Configuring DHCP Option 43” section on page F-1. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
There has been a software failure; a disconnect then errors reconnect of the unit power may resolve the issue Cycling through Red, This is a general warning of insufficient inline power. Green, Amber and Off Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Step 2 Click Wireless, and verify that your access point MAC address is listed under Ethernet MAC. Step 3 Log out of the controller, and close your web browser. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
The power injector (AIR-PWRINJ1500-2=) has three LEDs on the front end of the case (see Figure 3-1). For detailed information on the power injector, see the Cisco Aironet 1550 Series Outdoor Access Point Power Injector Installation Instructions. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide...
Power Injector Connectors and LEDs Mounting tabs AC POWER LED AP POWER LED TO AP—Ethernet connector (RJ-45) to access point (10/100/1000BASE-T) FAULT LED TO SWITCH—Ethernet connector (RJ-45) to switch (10/100/1000BASE-T) Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Inspect the seal of the plug and properly tighten it every time the plug is removed and replaced. Tighten Caution the plug to 15 lbf-in. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Replace the hex-shaped plug back and tighten it to 15 lbf-in. Step 4 Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 80
Chapter 3 Troubleshooting Using the Reset Button Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide 3-10 OL-32138-01...
For translated safety warnings, refer to the safety warning document that shipped with your access point or that is available on Cisco.com. To browse to the document on Cisco.com, follow these steps: Click this link and go to the Cisco Wireless documentation home page: Step 1 http://www.cisco.com/en/US/products/hw/wireless/index.html Click Support and the Support and Documentation page displays.
A P P E N D I X Declarations of Conformity and Regulatory Information This appendix provides declarations of conformity and regulatory information for the Cisco Aironet 1570 Series Outdoor Access Points. This appendix contains the following sections: Manufacturers Federal Communication Commission Declaration of Conformity Statement, •...
Increase separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from which the receiver is connected. • Consult the dealer or an experienced radio/TV technician. • Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Cisco Aironet Access Points are certified to the requirements of RSS-210. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations.
Antennas that have less than 8 dBi gain should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons. This access point is also compliant to EN 50835 for RF exposure. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by Cisco Systems. The use of software or firmware not provided and supported by Cisco Systems may result in the equipment no longer being compliant with the regulatory requirements.
Page 88
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 89
This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to Note certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance. The product carries the CE Mark:...
This system has been evaluated for RF exposure for Humans as referenced in the Australian Radiation Protection standard and has been evaluated to the ICNIRP (International Commission on Non-Ionizing Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
8 dBi to 14 dBi gain, is 19.7 inches (50 cm) from general bystanders. The minimum separation distance from antennas that have less than 8 dBi gain to general bystanders is 7.9 inches (20 cm). Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Guidelines for Operating Cisco Aironet Access Points in Japan Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English.
When such trouble occurs, the user may be required to take corrective actions. Administrative Rules for Cisco Aironet Access Points in Taiwan This section provides administrative rules for operating Cisco Aironet Access Points in Taiwan. The rules are provided in both Chinese and English. Chinese Translation...
The U-NII devices shall accept any interference from legal communications and shall not interfere the legal communications. If interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide B-12 OL-32138-01...
Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to CISCO-designated products.
This equipment operates on a secondary basis and consequently must accept harmful interference, including interference from stations of the same kind. This equipment may not cause harmful interference to systems operating on a primary basis. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide B-14 OL-32138-01...
Step 5 Click Install and Upgrade. Click Install and Upgrade Guides. Step 6 Click Channels and Maximum Power Settings for Cisco 1570 Series Outdoor Access Points document. Step 7 Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 98
Appendix C Channels and Power Levels Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
The detailed technical specifications for the Cisco Aironet 1570 Series Outdoor Access Points are available at the following URL: You can also download a copy of the Cisco Aironet 1570 Series Outdoor Access Point Data Sheet from the above URL for offline use.
Page 100
Appendix D Access Point Data Sheet Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Access Point PoE-In Ethernet Connector Pinouts for AIR-POWERINJ1500 Pin Number Signal Name Ethernet signal pair (10/100/1000BASE-T) and DC return Ethernet signal pair (10/100/1000BASE-T) and DC (+) Ethernet signal pair (1000BASE-T) and DC (+) Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Page 102
Ethernet signal pair (10/100/1000BASE-T) and DC return Ethernet signal pair (10/100/1000BASE-T) and DC (+) Ethernet signal pair (1000BASE-T) and DC (+) Ethernet signal pair (1000BASE-T) and DC return Shield Chassis ground Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide OL-32138-01...
Configuring DHCP Option 43 This appendix describes the steps needed to configure DHCP Option 43 on a DHCP server, such as a Cisco Catalyst 3750 series switch, for use with Cisco Aironet Access Points. This appendix contains these sections: Overview, page F-2 •...
Overview Overview This section contains a DHCP Option 43 configuration example on a DHCP server for use with Cisco Aironet Access Points. For other DHCP server implementations, consult DHCP server product documentation for configuring DHCP Option 43. In Option 43, use the IP address of the controller management interface.
43 ascii “Comma Separated IP Address List” For example, if you are configuring Option 43 for Cisco 1000, 1500, or 1500 series access points using the controller IP addresses 10.126.126.2 and 10.127.127.2, add the following line to the DHCP pool in the Cisco IOS CLI: option 43 ascii “10.126.126.2,10.127.127.2”...
Configuring Option 43 for 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1570 Series Access Points To configure DHCP Option 43 for Cisco Aironet 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1570 series access points in the embedded Cisco IOS DHCP server, follow these steps: Enter configuration mode at the Cisco IOS CLI.
High gain antennas have a more focused radiation pattern in a specific direction. A station is configured properly to allow it to wirelessly communicate with an associated access point. Adaptive Wireless Path Protocol. AWPP Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide GL-1 OL-32138-01...
Page 108
Glossary Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide GL-2 OL-32138-01...
Page 109
A ratio of decibels to an isotropic antenna that is commonly used to measure antenna gain. The greater the dBi value, the higher the gain, and the more acute the angle of coverage. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide GL-3 OL-32138-01...
Page 110
Software that is programmed on a memory chip. firmware A device that connects two otherwise incompatible networks together. gateway Gigahertz. One billion cycles per second. A unit of measure for frequency. Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide GL-4 OL-32138-01...
Page 111
The echoes created as a radio signal bounces off of physical objects. multipath A single data message (packet) sent to multiple addresses. multicast packet Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide GL-5 OL-32138-01...
Page 112
A feature of some access points that allows users to move through a facility roaming while maintaining an unbroken connection to the LAN. A connector type unique to Cisco Aironet radios and antennas. Part 15.203 of RP-TNC the FCC rules covering spread spectrum devices limits the types of antennas that may be used with transmission equipment.
Page 113
A single data message (packet) sent to a specific IP address. unicast packet Cisco Universal Power Over Ethernet (UPOE) extends IEEE PoE+ standard by UPoE doubling the power per port to 60W over a single standard Ethernet Cable. It allows the consolidation of 60 watts power on a single Ethernet (CAT5E or higher) cable, or in short 60W per access switch port.
Page 114
Wireless LAN Solutions Engine. The WLSE is a specialized appliance for WLSE managing Cisco Aironet wireless LAN infrastructures. It centrally identifies and configures access points in customer-defined groups and reports on throughput and client associations. WLSE's centralized management capabilities are further enhanced with an integrated template-based configuration tool for added configuration ease and improved productivity.