Subscribe to Our Youtube Channel
Related Manuals for Samlexpower 60S-12A
Summary of Contents for Samlexpower 60S-12A
-
Page 1: Instruction Manual
PURE SINE WAVE DC TO AC POWER INVERTER 60S-12A / 60S-24A 60S-12E / 60S-24E 100S-12A / 100S-24A 100S-12E / 100S-24E 150S-12A / 150S-24A 150S-12E / 150S-24E 200S-12A / 200S-24A 200S-12E / 200S-24E Instruction manual... - Page 2 - P1 -...
- Page 3 - P2 -...
- Page 4 - P3 -...
- Page 5 - P4 -...
- Page 6 - P5 -...
- Page 7 - P6 -...
- Page 8 - P7 -...
- Page 9 - P8 -...
- Page 10 - P9 -...
-
Page 11: Table Of Contents
Sine Wave Inverter Please read this manual carefully before installing and starting up and store it in a safe place. If the device is resold, this instruction manual must be handed over to the purchaser along with the device. Contents 1 Notes on using the instruction manual. -
Page 12: Notes On Using The Instruction Manual
Notes on using the instruction manual Sine Wave Inverter Notes on using the instruction manual Caution! Safety instruction, failure to observe this instruction can cause material damage and impair the function of the device. Supplementary information for operating the device. Caution! Safety instruction relating to a danger from electrical current or voltage. - Page 13 Sine Wave Inverter General safety instructions Use the device only as intended. Do not operate the device in a damp or wet environment. Do not operate the device in areas that are potentially explosive. Maintenance and repair work must only be carried out by qualified per- sonnel who are familiar with the risks involved and the relevant regula- tions.
-
Page 14: Scope Of Delivery
Sine wave inverter Operating Instructions Proper use The Pure Sine Wave Inverters convert 12 V (60S-12A/E, 100S-12A/E, 150S- 12A/E, 200S-12A/E) or 24 V (60S-24A/E, 100S-24A/E, 150S-24A/E, 200S- 24A/E) direct current to a 115V or 230V alternating current at a frequency of 50 Hz or 60Hz. -
Page 15: Technical Description
Sine Wave Inverter Technical description 5 Technical description The inverters can be operated wherever there is a 12 V DC supply (60S- 12A/E, 100S-12A/E, 150S-12A/E, 200S-12A/E) or a 24 V DC supply (60S- 24A/E, 100S-24A/E, 150S-24A/E, 200S-24A/E). With its low weight and the compact design, the inverter can be easily installed into Camping mobiles, commercial vehicles or motor and sailing yachts. -
Page 16: Installation Instructions
Installing the inverter Sine Wave Inverter For making and testing the electrical connection the following tools are required: Crimping tool 3 different flexible cable connections. The required cable diameter can be taken from the table in the section „Connecting the inverter“ on page Various terminals, multicore cable ends For fixing the inverter you need the following mounting devices: Screws (M4) with spacers and self-locking nuts or sheet metal screws... -
Page 17: Connecting The Inverter
On building up an electricity supply network the safety regulations according to the VDE 0100 standard are to be kept. Observe the required cable cross section (see table). Device Required cable cross section 60S-12A/E 25 – 50 mm² 60S-24A/E 100S-12A/E 35 – 50 mm²... -
Page 18: Using The Inverter
5). When switching on, the ”Power” LED (fig. 1.2, page 1 / fig. 10.3, page 5) illuminates. Malfunctions When the battery voltage falls below 10.7 V (60S-12A/E, 100S-12A/E, 150S- 12A/E, 200S-12A/E) resp. 21.4 V (60S-24A/E, 100S-24A/E, - P17 -... - Page 19 5) for 1500W and 2000W on the front panel and for 600W (option) and 1000W on the bottom plate. GFCI for 60S-12A/E, 60S-24A/E, 100S-12A/E, 100S-24A/E is an option GFCI for 150S-12A/E, 150S-24A/E, 200S-12A/E, 200S-24A/E is a must An un-intentional electric path between a source of current and a grounded surface is referred to as a “ground fault”.
-
Page 20: Rectifying Faults
Rectifying faults Sine Wave lnverter Rectifying faults Fault Cause Remedy No output voltage, LED not Bad connection between Check the cables and contact Illuminated battery and inverter. Internal fuses defect. In this case send the unit back to supplier. No output voltage, OVER- The inverter has been over- Switch off the inverter and the TEMP LED illuminates... -
Page 21: Cleaning And Caring For The Inverter
Sine Wave lnverter Cleaning and caring for the inverter Cleaning and caring for the inverter Caution! Do not use sharp or hard objects for cleaning as these may damage the device. Occasionally clean the device with a damp cloth. 11 Guarantee Our general guarantee conditions apply. -
Page 22: Technical Data
Technical data Sine Wave lnverter Technical data 600W Pure Sine Wave Inverter Item number 60S-12E 60S-24E 60S-12A 60S-24A Rated input voltage 12 V DC 24 V DC 12 V DC 24 V DC Constant output power 600 W Peak output power 1000 W (a max. - Page 23 Sine Wave lnverter Technical data Technical data 1000W Pure Sine Wave Inverter Item number 100S-12E 100S-24E 100S-12A 100S-24A Rated input voltage 12 V DC 24 V DC 12 V DC 24 V DC Constant output power 1000 W Peak output power 2000 W (a max.
- Page 24 Technical data Sine Wave lnverter Technical data 1500W Pure Sine Wave Inverter Item number 150S-12E 150S-24E 150S-12A 150S-24A Rated input voltage 12 V DC 24 V DC 12 V DC 24 V DC Constant output power 1500 W Peak output power 3000 W (a max.
- Page 25 Sine Wave lnverter Technical data Technical data 2000W Pure Sine Wave Inverter Item number 200S-12E 200S-24E 200S-12A 200S-24A Rated input voltage 12 V DC 24 V DC 12 V DC 24 V DC Constant output power 2000 W Peak output power 4000 W (a max.
- Page 26 902SI200000005...
Need help?
Do you have a question about the 60S-12A and is the answer not in the manual?
Questions and answers