Advertisement
Available languages
Available languages
Mode of
Operation
Return to
"Auto" MODE knob arrow
Motion Activated Setting
points to a time selection
from any of
the above settings.
ENERGY STAR
®
ENERGY STAR
®
is sponsored by the U.S.
Environmental Protection Agency & U.S.
Department of Energy.
Visit www.energystar.gov to learn more.
To meet ENERGY STAR
®
requirements, the photo sensor control knob must be in the "Auto"
mode to prevent operation during full daylight. Maximum lamp wattage cannot exceed 250 watts.
TROUBLESHOOTING
Problem
Cause / Solution
Outdoor Lights
No power to the fixture.
• Check if circuit breaker tripped.
Do Not Come
On With Motion
• Confirm wall switch is ON.
At Night
Bulb is faulty.
• Replace bulb.
Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
• Re-aim the head.
• Relocate or reposition the unit away from the light.
TURN OFF POWER BEFORE CONTINUING
Wiring to the unit is loose.
• Check wiring, and reconnect if necessary using wire
nuts (H) provided.
Outdoor Lights
There is motion in the detection zone.
• Make sure the sensor is not picking up moving objects such as
Come On For No
trees, traffic, etc.
Apparent Reason
TEST FOR YOURSELF.
At Night
• Cover the sensor lens with cardboard to prevent sensor from
detecting motion. If the light stays off, something in the detection
zone is triggering the sensor.
• If this is the case, reduce the sensitivity.
• Reposition the sensor.
* If the light stays on with the sensor lens covered, contact
customer service.
Unit is in the motion activated setting.
• Make sure "Auto" MODE knob is set between 1m-12m.
There is motion in the detection zone.
Lights Stay On At
Night And Do
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
Not Turn Off
• Reduce the sensitivity.
• Reposition the sensor.
Unit is in override mode (if there is no motion).
• Turn the light switch to the OFF position for 90 seconds, and then
turn back to the ON postion. This will send the unit back into the
motion activated setting "Auto".
* If the light stays on with the sensor lens covered, contact
customer service.
Unit is in the "Auto" mode.
• Make sure the unit is set between 1m-12m ("Auto" mode).
Lights
The light given from the unit's own lamp is affecting the
motion sensor.
Continuously
• Re-aim the lamp.
Blink On and
• Reposition motion sensor.
Off At Night
Make sure knob is not positioned between TEST and 1m.
• Reposition knob closer to selected function, either TEST, or 1m.
The controls on the bottom of the motion sensor are in the test mode.
Lights Are On
During The Day
• Reposition MODE knob off of TEST to a time selection (1m-12m).
The motion detector is shadowed.
• Reposition motion sensor.
During daylight hours, the red LED indicator will flash when motion
Red LED Indicator
is detected. This is normal.
Light Comes ON
And OFF During
Daylight Hours
MODE Knob
How to Set
Adjustment
Power Switch
Turn the power OFF
for at least 90 seconds
within the 1m-12m
and then back ON.
time range.
2-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting, LLC ("Cooper Lighting") warrants to customers that, for a period of two years
from the date of purchase, Cooper Lighting's products will be free from defects in materials
and workmanship. The obligation of Cooper Lighting under this warranty is expressly limited
to the provision of replacement products. This warranty is extended only to the original
purchaser of the product. A purchaser's receipt or other proof of date of original purchase
acceptable to Cooper Lighting. This is required before warranty performance shall be rendered.
This warranty does not apply to Cooper Lighting products that have been altered or repaired
or that have been subjected to neglect, abuse, misuse or accident (including shipping damages).
This warranty does not apply to products not manufactured by Cooper Lighting which have been
supplied, installed, and/or used in conjunction with Cooper Lighting products. Damage to the
product caused by replacement bulbs or corrosion or discoloration of brass components are
not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL COOPER LIGHTING BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT,
STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL
THE LIABILITY OF COOPER LIGHTING FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR
CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE,
REPAIR OR MODIFICATION OF COOPER LIGHTING PRODUCTS, OR SUPPLY OF ANY REPLACEMENT
PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF COOPER LIGHTING PRODUCTS GIVING RISE
TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
To obtain warranty service, please contact Cooper Lighting, LLC, at 1-800-334-6871, press
option 2 for Customer Service, or via e-mail ConsumerProducts@cooperlighting.com and
include the following information:
• Name, address and telephone number
• Date and place of purchase
• Catalog and quantity purchase
• Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization Number issued
by the Company and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company will be refused.
Cooper Lighting, LLC is not responsible for merchandise damaged in transit. Repaired or
replaced products shall be subject to the terms of this warranty and are inspected when
packed. Evident or concealed damage that is made in transit should be reported at once to
the carrier making the delivery and a claim filed with them.
Reproductions of this document without prior written approval of Cooper Lighting, LLC are strictly prohibited.
For assistance, call 1-800-334-6871 or e-mail us at ConsumerProducts@cooperlighting.com
Printed in China
ESPAÑOL
ARTÍCULOS NECESARIOS
(se compran por separado)
• Destornillador en cruz (Phillips)
• Calafateo de silicona resistente a la intemperie
CÓMO FUNCIONA
PIR funciona muy bien en la detección de movimiento lateral
en un rango de detección de 270°. El Radar Doppler Precision
Plus™ hace un excelente trabajo detectando movimiento de
acercamiento y alejamiento de la unidad. La combinación de
ambos sistemas proporciona precisión avanzada y cobertura
completa dentro del rango de detección. El movimiento desde
cualquier dirección disparará el reflector–incluso en temperaturas
extremas de calor y frío.
ADVERTENCIAS Y PRECAUCIONES
• Lea estas instrucciones.
• Guarde estas instrucciones.
• Atienda todas las advertencias.
• Siga todas las instrucciones.
• Sólo para uso en exteriores.
• cULus para ubicaciones mojadas.
• El portalámparas debe estar conectado a una fuente de energía de 120 Voltios, 60 Hz.
Cualquier otro tipo de conexión anula la garantía.
• El portalámparas debe ser instalado por personas con experiencia en cableado doméstico o
por un electricista calificado. El sistema eléctricoy el método de conexión eléctrica del porta-
lámparas debe cumplir con el Código eléctrico nacional y los códigos locales sobre edificios.
• Reemplace siempre la bombilla con una del mismo vatiaje o más bajo que el marcado. Si
instala lámparas de mayor potencia, puede crear riesgo de incendio. Si usa lámparas de
mayor potencia, se anula la garantía. (Utilice una bombilla de halógeno de un máximo de
150 W.) Para cumplir con los requerimientos de ENERGY STAR®, la potencia máxima de la
bombilla no debe exceder 250 W.
3
Hasta
90 pies
270 grados
Advertisement
