Page 1
KD-SX8350 3 7 63 1515 0 SERVICE MANUAL CD RECEIVER 49782 2003 KD-SX8350 SOUND SOURCE L 13942296513 Area Suffix Northern America TABLE OF CONTENTS Important Safety Precautions ............1-2 Disassembly method .
KD-SX8350 3 7 63 1515 0 SECTION 1 Important Safety Precautions 1.1 Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.
Page 3
KD-SX8350 3 7 63 1515 0 1.2 Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
KD-SX8350 3 7 63 1515 0 SECTION 2 Disassembly method 2.1 Main body 2.1.1 Removing the front panel assembly Front panel assembly (See Fig.1.) Release button (1) Push the release button and remove the front panel as- sembly. Fig.1 2.1.2 Removing the bottom cover...
Page 5
KD-SX8350 3 7 63 1515 0 2.1.3 Removing the front chassis assembly Joint d Joint e (See fig.3,4) • Prior to performing the following procedure, remove the front panel assembly and the bottom cover. (1) Remove the screws A on the both sides of the body.
Page 6
KD-SX8350 3 7 63 1515 0 2.1.6 Removing the main board assembly Main board assembly (See fig.7) • Prior to performing the following procedure, remove the front panel assembly, the front chassis, the heat sink, the rear panel and the bottom cover.
Page 7
KD-SX8350 3 7 63 1515 0 2.1.8 Remove the LCD key operation board (See fig.9~11) • Prior to performing the following procedure, remove the front panel assembly. (1) Remove the four screws J on the back of the front panel as- sembly.
Page 8
KD-SX8350 3 7 63 1515 0 2.2 CD Mechanism Assembly 2.2.1 Removing the top cover (See Figs.1 and 2) (1) Remove the two screws A on the both side of the body. (2) Lift the front side of the top cover and move the top cover backward to release the two joints a.
Page 9
KD-SX8350 3 7 63 1515 0 2.2.2 Removing the connector board Wires (See Figs.3 to 5) CAUTION: Before disconnecting the flexible wire from the pickup, solder the short-circuit point on the pickup. No observance of this in- struction may cause damage of the pickup.
Page 10
KD-SX8350 3 7 63 1515 0 2.2.3 Removing the DET switch (See Figs.6 and 7) (1) Extend the two tabs c of the feed sw. holder and pull out the switch. (2) Unsolder the DET switch wire if necessary.
Page 11
KD-SX8350 3 7 63 1515 0 2.2.4 Removing the chassis unit (See Figs.8 and 9) • Prior to performing the following procedure, remove the top Chassis unit cover and connector board. Suspension spring (L) Suspension spring (R) (1) Remove the two suspension springs (L) and (R) attaching the chassis unit to the frame.
Page 12
KD-SX8350 3 7 63 1515 0 2.2.5 Removing the clamper assembly (See Figs.10 and 11) • Prior to performing the following procedure, remove the top cover. (1) Remove the clamper arm spring. Clamper arm spring (2) Move the clamper assembly in the direction of the arrow to release the two joints d.
Page 13
KD-SX8350 3 7 63 1515 0 2.2.6 Removing the loading / feed motor assembly (See Figs.12 and 13) • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw C and move the loading / feed motor as- sembly in the direction of the arrow to remove it from the chassis rivet assembly.
Page 14
KD-SX8350 3 7 63 1515 0 2.2.7 Removing the pickup unit Pickup unit (See Figs.14 to 18) • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw D and pull out the pu. shaft holder from Part e the pu.
Page 15
KD-SX8350 3 7 63 1515 0 2.2.9 Removing the trigger arm Joint k (See Figs.19 and 20) • Prior to performing the following procedure, remove the top cover, connector board and clamper unit. (1) Turn the trigger arm in the direction of the arrow to release Trigger arm the joint k and pull out upward.
Page 16
KD-SX8350 3 7 63 1515 0 2.2.11 Removing the mode sw. / select lock arm Link plate Joint t (See Figs.22 and 23) Mode sw. • Prior to performing the following procedure, remove the top plate assembly. Select lock arm (1) Bring up the mode sw.
Page 17
KD-SX8350 3 7 63 1515 0 2.2.12 Reassembling the mode sw. / select lock arm Select lock arm spring (See Figs.24 to 26) Hook w REFERENCE: Reverse the above removing procedure. Joint v (1) Reattach the select lock arm spring to the top plate and set...
Page 18
KD-SX8350 3 7 63 1515 0 2.2.13 Removing the select arm R / link plate Joint c' Link plate Joint r (See Figs.27 and 28) Select arm R Joint b' • Prior to performing the following procedure, remove the top plate assembly.
Page 19
KD-SX8350 3 7 63 1515 0 2.2.15 Removing the loading roller assembly Loading roller assembly (See Figs.31 to 33) • Prior to performing the following procedure, remove the Roller guide spring clamper assembly and top plate assembly. (1) Push inward the loading roller assembly on the gear side and detach it upward from the slot of the joint g' of the lock arm rivet assembly.
Page 20
KD-SX8350 3 7 63 1515 0 2.2.16 Removing the loading gear 5, 6 and 7 Loading gear bracket (See Figs.35 and 36) • Prior to performing the following procedure, remove the top Loading gear 6 cover, chassis unit, pickup unit and top plate assembly.
KD-SX8350 3 7 63 1515 0 2.2.17 Removing the gears Joint p' (See Figs.37 to 40) • Prior to performing the following procedure, remove the top Change plate rivet assembly cover, chassis unit, top plate assembly and pickup unit.
KD-SX8350 3 7 63 1515 0 2.2.18 Removing the turn table / spindle motor Turn table (See Figs.41 and 42) • Prior to performing the following procedure, remove the top cover, connector board, chassis unit and clamper assembly. (1) Remove the two screws L attaching the spindle motor as- sembly through the slot of the turn table on top of the body.
FM 87.5MHz ~ 107.9MHz 6. Digital tester AM 530kHz ~ 1710kHz 7. Tracking offset meter 8. Test Disc JVC : CTS-1000 9. Extension cable for check EXTSH002-22P × 1 Dummy load Exclusive dummy load should be used for AM, and FM. For FM dummy load, there is a loss of 6dB between SSG output and antenna input.
Page 24
KD-SX8350 3 7 63 1515 0 3.2 Troubleshooting 3.2.1 Feed section Is the voltage output at Is the wiring for IC521 Is 5V present at IC581 Check CD 9V IC521 pin u 5V or 0V? (90) ~ (100) correct? pin 6? and 5V.
Page 25
KD-SX8350 3 7 63 1515 0 3.2.5 Signal processing section No sound from either Compare the L-ch and R-ch Is the sound output from channel. to locate the defective point. both channels (L, R)? Check the vicinity of the...
Page 26
KD-SX8350 3 7 63 1515 0 3.3 Maintenance of laser pickup 3.4 Replacement of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens Turn off the power switch and, disconnect the power cord with a alcohol soaked cotton swab.
Page 29
KD-SX8350 3 7 63 1515 0 4.3 HD74HC126FP-X (IC771) : Buffer • Pin layout • Pin function Input Output Note: H:High level L:Low level X:Irrelevant Z:Off(High-impedance) State a 3-state input • Block diagram Output Input L 13942296513 Output Sample as Load Circuit 1...
Page 30
KD-SX8350 3 7 63 1515 0 4.5 LA47505 (IC351) : Power amp. • Pin layout & Block daiagram Protective circuit Stand by Switch L 13942296513 Ripple Mute Filter circuit protective circuit Muting & On Time Control Circuit u163 1-30 (No.49782)
Page 31
KD-SX8350 3 7 63 1515 0 • Pin layout • Pin function Pin No. Symbol Function AC CONT1 Header of IC GND1 Power GND OUTFR- Outpur(-) for front Rch STBY Stand by input OUTFR+ Output (+) for front Rch...
Page 39
KD-SX8350 3 7 63 1515 0 Pin No Symbol Descroption EFM and PLCK phase difference signal output pin. TMAX TMAX detection result output pin. TMAX Detection Result TMAX Output Longer than fixed period "PV " Within fixed period "HiZ"...
Page 40
KD-SX8350 3 7 63 1515 0 4.12 UPD784215AGC149 (IC701) : CPU • Pin layout • Pin function Pin No. Symbol Function Non connected Non connected Detection switch of CD mechanism CD mecha position setting SW Loading motor control signal output...
Page 41
KD-SX8350 3 7 63 1515 0 OPEN CD tray open control signal output Non connected Non connected Non connected Non connected SD/ST Station detector and stereo signal input. It is H and there is a bureau.It is L and a stereo.
Page 42
KD-SX8350 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.49782) Printed in Japan 200302WPC http://www.xiaoyu163.com...
Page 43
KD-SX8350 3 7 63 1515 0 SCHEMATIC DIAGRAMS CD RECEIVER KD-SX8350 CD-ROM No.SML200302 SOUND SOURCE L 13942296513 Area Suffix Northern America Contents Block diagram Standard schematic diagrams Printed circuit boards 2-8~10 u163 No.49782SCH COPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LTD.
http://www.xiaoyu163.com 3 7 63 1515 0 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 55
KD-SX8350 3 7 63 1515 0 < M E M O > L 13942296513 u163 2-11 http://www.xiaoyu163.com...
Page 56
KD-SX8350 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY 10-1,1Chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.49782SCH) 2003/02 http://www.xiaoyu163.com...
KD-SX8350 3 7 63 1515 0 PARTS LIST [ KD-SX8350] * All printed circuit boards and its assemblies are not available as service parts. Area suffix J -------------- Northern America L 13942296513 - Contents - 3- 2 Exploded view of general assembly and parts list (Block No.M1) 3- 5 CD mechanism assembly and parts list (Block No.MB)
Page 58
KD-SX8350 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. L 13942296513 u163 http://www.xiaoyu163.com...
Page 59
KD-SX8350 3 7 63 1515 0 Parts list (Genereal assembly) Block No. M1MM Item Description Parts number Parts name Q'ty Area CD MECHA --------------------- GE10043-205A TOP CHASSIS GE30568-006A HEAT SINK GE30393-002A BOTTOM COVER FSMA3005-001 INSULATOR QYSDST2604Z SCREW 3 CHASSIS+CD MECH...
Page 60
KD-SX8350 3 7 63 1515 0 Parts list (Genereal assembly) Block No. M1MM Item Description Parts number Parts name Q'ty Area VKW3001-330 COMP.SPRING 1 FOR DETACH BUTT GE10042-004A REAR COVER FSYH4036-078 INSULATOR SHEET 1 REAR COVER VKZ4777-001 MINI SCREW...
Page 61
KD-SX8350 3 7 63 1515 0 CD mechanism assembly and parts list Block No. Grease TNG-87 TN-2001-1011 GP-501MK CFD-005Z GP-501A L 13942296513 u163 http://www.xiaoyu163.com...
KD-SX8350 3 7 63 1515 0 Parts list (CD mechanism) Block No. MBMM Item Description Parts number Parts name Q'ty Area FRAME 30320101T 30320102T TOP COVER 30320115T DANPER F 30320116T DANPER R 303205505T CHASSIS RIVET 303205503T CHANGE P. RVT A...
KD-SX8350 3 7 63 1515 0 Parts list (CD mechanism) Block No. MBMM Item Description Parts number Parts name Q'ty Area 30321103T LOADING GEAR 3 30321104T LOADING GEAR 4 30321105T LOADING GEAR 5 30321106T LOADING GEAR 6 LOADING GEAR 7...
Page 64
KD-SX8350 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area B 705 NCS31HJ-101X C CAPACITOR C 341 QERF1AM-107Z E CAPACITOR 100MF 20% 10V...
Page 65
KD-SX8350 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 528 NCB31EK-333X C CAPACITOR C 772 NCB31HK-103X C CAPACITOR C 529...
Page 66
KD-SX8350 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area D 711 SLR-56MC3F L.E.D. R 256 NRSA63J-104X MG RESISTOR D 714 UDZS5.1B-X...
Page 67
KD-SX8350 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area R 356 NRSA02J-103X MG RESISTOR R 561 NRSA63J-333X MG RESISTOR R 357...
Page 68
KD-SX8350 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area R 743 NRSA63J-473X MG RESISTOR R 744 NRSA63J-0R0X MG RESISTOR R 745 NRSA63J-0R0X MG RESISTOR R 746 NRSA63J-103X...
Page 69
KD-SX8350 3 7 63 1515 0 Electrical parts list (Front board) Block No. 02 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 601 NBE20JM-475X TS E CAPACITOR R 625 NRSA02J-122X MG RESISTOR...
Page 70
KD-SX8350 3 7 63 1515 0 Packing materials and accessories parts list Block No. Block No. A1~A8 L 13942296513 KIT:A9~A13 u163 3-14 http://www.xiaoyu163.com...
Page 71
1 FOR J LVT0717-001B TROUBLE SHEET(C BT-52006-2 WARRANTY CARD 1 FOR C BT-51028-2 J=REGIST CARD 1 FOR J BT-20071B JVC CENTER LIST 1 FOR C VKZ4027-202 PLUG NUT MOUNT BOLT A 10 VKH4871-001SS A 11 VKZ4328-001 LOCK NUT L 13942296513...