Subscribe to Our Youtube Channel
Related Manuals for TYROLIT Hydrostress DME19DPP
Summary of Contents for TYROLIT Hydrostress DME19DPP
-
Page 1: Instruction Manual
Instruction Manual DME19DP Index 001 as of Serial No. 830 794 Translation of the Original Instruction Manual 10997907 en / 23.11.2016... - Page 2 Congratulations! You have opted to buy a tried and tested TYROLIT Hydrostress machine and therefore a leading technological standard. Only original TYROLIT Hydrostress spare parts guarantee quality and replaceability. If the maintenance work is neglected or carried out improperly we are unable to fulfil our guarantee undertaking.
-
Page 3: Table Of Contents
Contents Contents ........................... 3 Important Information ......................4 Pictograms ..........................4 Explanation of the pictograms on the dry drilling motor ............4 Explanation of the pictograms used in the text ............... 4 For your Safety ........................5 General Safety Instructions for Power Tools ................5 1) Safety at the place of work .................... -
Page 4: Important Information
Important Information Before starting any work with or on the machine, this instruction manual, the safety instructions and the warnings must be read through carefully and ob- served. Always store this instruction manual together with the machine. Pictograms Explanation of the pictograms on the dry drilling motor The CE mark on a product means that the product conforms with all the applicable European regulations and has been subjected to the prescribed conformity assessment procedures. -
Page 5: For Your Safety
For your Safety General Safety Instructions for Power Tools WARNING Read all the safety instructions and precautions. Failure to observe the safety instructions and precautions can result in electric shock, fire and/or serious injuries. Keep all safety instructions and precautions for future reference. The term “power tool”... -
Page 6: Safety Of Persons
For your Safety 3) Safety of persons Always work carefully, attentively and sensibly when using a power tool. Do not use the power tools if you are tired or are under the influence of drugs, alcohol or medication. A moment of inattention while using the power tool can result in serious injuries. Wear personal protective equipment and always wear goggles. -
Page 7: Service
For your Safety Store power tools out of the reach of children when not in use. Do not allow people to use the tool unless they are familiar with it, or if they have not read this instruction manual. Power tools are dangerous if they are used by inexperienced people. Maintain power tools with care. -
Page 8: Electrical Safety
For your Safety • Dust from materials such as coatings containing lead, several types of wood, minerals and metals can be harmful to health and cause allergic reactions, respiratory diseases and/or cancer. Asbestos-containing material may only be machined by specialists. −... -
Page 9: Safety Of People
For your Safety Safety of people • Wear personal protective equipment and, depending on the work situation, use: Full-face protection, eye protection or safety glasses/goggles, hard hat and special apron Protect yourself against debris thrown up by wearing a hard hat, safety goggles or face protection and wear an apron, if necessary. -
Page 10: Hazards When Using And Handling The Power Tool
For your Safety • Never put down the power tool until the insert tool has come to a complete standstill. The rotating insert tool can come into contact with the surface on which the power tool is placed, which could cause you to lose control of the power tool. •... -
Page 11: Service / Maintenance / Repair
For your Safety • Allow the insert tools, tool holders and other parts cool in the immediate vicinity of the work area after use. The machines can be very hot after use, do not touch the parts, risk of injuries. •... -
Page 12: Technical Characteristics
Technical Characteristics Technical specifications DME19DPP Dry drilling motor Operating voltage (V / Hz) ~230 / 50-60 ~110 / 50-60 Power consumption (watt) 1800 Protection class two / II speed (min 1150 Impact frequency (imp) 28000 Core bit diameter min./ max. (mm) -
Page 13: Declaration Of Conformity
Declaration of Conformity Dry drilling motor DME19DPP We confirm with sole responsibility that this machine conforms to the following directives and standards Applied directive(s) 2006/42/EC; 2014/30/EU; 2011/65/EU Applied standards EN 60745 TYROLIT Hydrostress AG Witzbergstrasse 18 CH-8330 Pfäffikon Switzerland Pfäffikon, 19.12.2014... -
Page 14: Machine Parts And Controls
Machine Parts and Controls 1 Green LED 2 Red LED 3 Lock for ON / OFF switch 4 ON / OFF switch 5 Handle 6 Connection cable 7 Additional handle (can be mounted for left and right-handed persons) 8 Open-ended spanner SW36 9 Open-ended spanner SW41 10 Extraction tube 11 Clip for fastening extraction tube... -
Page 15: Tools And Accessories
Tools and Accessories Accessories: • Centring tip (450 mm long) TYROLIT No. 10995373 • Centring tip (250 mm long) TYROLIT No. 10997916 • Centring wingnut* • Extraction pin G½ TYROLIT No. 10995156 • ModulDrill collar adapter plate TYROLIT No. 10995087 •... -
Page 16: Before Starting Work
Before Starting Work Note and follow the following points before each use to ensure safe working with the dry drilling motor: • Read through all safety instructions and warnings in this instruction manual. • Check whether the voltage on the rating plate is identical with the mains voltage. •... -
Page 17: Switch Soft Impact Feature On And Off
Before Starting Work Switching soft impact feature on and off (Figure 2 and Figure 3) Attention! Only press the soft impact feature ON / OFF changeover switch if the power tool is switched off. Figure 2 Figure 3 Switch the drill's soft impact feature on or off, depending on the material to be drilled (Figure 2 and Figure 3). -
Page 18: Operation And Control
Operation and Control Fitting or replacing the diamond dry core bit (Figure 4) The diamond dry core bit is chosen for the required drilling diameter and is screwed onto the G½″ internal thread or 1¼″ UNC external thread of the output shaft. Please note! If the dry drilling motor is used in a drill stand, the machine must be fixed in the motor collar before the diamond dry core bit is fitted. -
Page 19: Hand-Held Drilling
Operation and Control Hand-held drilling Using the centring tip (Figure 5 to Figure 8) The centring tip can only be used with diamond dry core bits, which are screwed onto the 1¼″ UNC external thread of the output shaft. Figure 5 Figure 6 •... -
Page 20: Connect Dust Extractor To The Extraction Tube
Operation and Control Connecting the dust extractor to the extraction tube (Figure 9) Figure 9 • Check the dust extractor function and then push the dust extractor hose (3) firmly onto the socket (2) of the extraction tube (1). Please note! Greater effort may be required to push on the suction hose in cold ambient temperatures. -
Page 21: Finishing The Drilled Hole
Operation and Control • Mark the hole centre. • Switch on the dust extractor connected to the extraction tube. • Always hold on tight to both handles of the dry drilling motor with two hands. • Position the centring pin (2) on the marked hole centre (1) with light pressure. The diamond dry core bit must not touch the stone! •... -
Page 22: Ending The Drilling Process
Operation and Control Ending the drilling process (Figure 11, page 20) • Attention! The cutters of the diamond dry core bit can be easily damaged beyond repair if they get stuck in the core drillhole. ► Do not switch off the dry drilling motor until the rotating diamond dry core bit has been completely removed from the masonry. -
Page 23: Stand-Guided Core Drilling
Stand-guided core drilling Figure 13 DME19DP dry drilling motor Extraction pin TYROLIT diamond dry core bit ModulDrill collar adapter plate Drill core centring Drill stand with ModulDrill drilling motor holder Drill stand with collar drilling motor holder Dry vacuum cleaner* * Our recommendation for a dry vacuum cleaner: Max. -
Page 24: Handling Diamond Dry Core Bits
Handling diamond dry core bits A "soft" diamond dry core bit is used for hard stone, so that the diamond splinters are quickly freed from the segments during the drilling process. If extraction is not used during machining, the diamond dry core bit increasingly rubs against "soft"... - Page 28 TYROLIT Hydrostress AG Witzbergstrasse 18 CH-8330 Pfäffikon Switzerland Tel. 0041 (0) 44 952 18 18 Fax 0041 (0) 44 952 18 00 www.tyrolit.ch 01.2015 Subject to change without notice Printed in Germany...
Need help?
Do you have a question about the DME19DPP and is the answer not in the manual?
Questions and answers