1. Manuals
  2. Brands
  3. Huck Manuals
  4. Nail Gun
  5. 3585
  6. Instruction manual

Huck 3585 Instruction Manual

3585 series. hidraulic installation tools
Hide thumbs Also See for 3585:
Table of Contents

Advertisement

Quick Links

3585
Hydraulic Installation Tools
3585
series
3585PT
March 1, 2018
Makers of Huck
Brand Fasteners, Tools & Accessories
HK1080
Tool Components
12-13
, Marson
, Recoil
®
®
2
3-4
5
5
6
7
8
9
9
10
11
14
14
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 3585 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Huck 3585

Summary of Contents for Huck 3585

  • Page 1: Table Of Contents

    Preparation for Use 3585 Operating Instructions 3585PT Maintenance Sticker Locations Disassembly Procedure Assembly Procedure Tool Components Drawings 12-13 Kits and Accessories Troubleshooting Makers of Huck , Marson , Recoil March 1, 2018 ® ® ® Brand Fasteners, Tools & Accessories HK1080...

  • Page 2: Declaration Of Conformity

    3585 series Hydraulic Installation Tool (HK1080)

  • Page 3: Safety Instructions

    3. Be aware that failure of the workpiece, accessories, equipment. or the inserted tool itself can generate high velocity 2. Huck equipment must be maintained in a safe working projectiles. condition at all times. Tools and hoses should be 4. Always wear impact resistant eye protection during tool inspected at the beginning of each shift/day for operation.
  • Page 4 3585 series Hydraulic Installation Tool (HK1080) Safety Instructions (continued) IV. REPETITIVE MOTION HAZARDS: instructions and as required by occupational health and 1. When using assembly power tool, the operator can safety regulations. experience discomfort in the hands, arms, shoulders, 4. Operate and maintain tool as recommended in the neck or other parts of the body.

  • Page 5: Tool Description Instruction Manual

    3585 series Hydraulic Installation Tool (HK1080) Description The 3585 series Hydraulic Installation Tools are cylinder MODEL 3585 and piston assemblies; complete with handle, hoses, Installs -16 (1/2”) to -24 (3/4”) Pintail-style Lockbolt couplers, and a control cord, and are ready to be attached...

  • Page 6: Principle Of Operation

    3585 series Hydraulic Installation Tool (HK1080) Principle of Operation Piston Travel Piston Travel PULL Piston Pintail Ejector Dump Trigger Valve Switch Hydraulic Hoses Pressurized Oil Return Oil PULL RETURN PULL RETURN PRESSURE PRESSURE PRESSURE PRESSURE PULL Pressure (PULL Cycle) RETURN Pressure (RETURN Cycle)

  • Page 7: Preparation For Use

    Ensure adequate clearance for operator’s hands before proceeding. and hydraulic fluid Only HUCK Powerig® Hydraulic Units should be used to power free of foreign matter. HUCK tools. Hydraulic units that deliver high PULL and RETURN Contaminated fluid can pressures must be equipped with relief valves;...

  • Page 8: Operating Instructions

    3585 series Hydraulic Installation Tool (HK1080) Operating Instructions FOR SAFE OPERATION, THIS SECTION MUST BE READ AND UNDERSTOOD. Bead UP Flange DOWN CORRECT CORRECT Do NOT install a fastener without a Do NOT pull a workpiece (structure to be fastened), a fastener with the pin, and a properly oriented collar in place.

  • Page 9: Maintenance

    Sticker Locations HUCK tools are labeled with important stickers that contain safety and pressure-settings information. These stickers must remain on the tools and be legible. A sticker must be ordered and replaced on the tool, in the location shown, if it becomes damaged or worn, it has been removed from the tool, or when replacing the Cylinder.

  • Page 10: Disassembly Procedure

    5. Model 3585: Remove the retaining ring and cover plate. Model 3585PT: Remove the screws and the retainer. 6. Model 3585: Use the End Cap Hex Wrench (P/N 126981) to remove the end cap. Model 3585PT: Use the End Cap Hex Wrench (P/N 126981) to remove the end cap assembly.

  • Page 11: Assembly Procedure

    Before re-assembling the tool: placed in closest matching grooves. • Clean components in mineral spirits or other solvent 12. Model 3585: After the end cap is locked in place, compatible with O-ring seals. install the cover plate and retaining ring. •...
  • Page 12 3585 series Hydraulic Installation Tool (HK1080) 3585 Components Drawing 23 24 25 26 27 28 29 1 Figure 3 21f 21g 20 19 18 21a 21b 21c 21d 21e 21 - Ejector Gland Assembly Detail Item Description Qty. Cylinder 128673...
  • Page 13 3585 series Hydraulic Installation Tool (HK1080) 3585PT Components Drawing 2b 3b 3a 23, 24 4c 4d Figure 4 2d 2c 8, 9 14, 15 10, 25 3585PT_revH Item Description Item Description Item Description Cylinder 128673 O-Ring 504639 Trigger/O-Ring Assy 120361...

  • Page 14: Kits And Accessories

    3. Tool leaks hydraulic fluid. b. Scored anvil. Defective tool O-rings or loose hose connections at tool. Shear collar on HUCK Blind Fastener not driven. Improper tool operation. 4. Hydraulic couplers leak fluid. b. Worn or damaged driving anvil in nose assembly. Damaged or worn O-rings in coupler body. See Coupler 110440.
  • Page 15 Determination is Outside USA and Canada made on a case-by case basis upon return of parts to Huck Contact your nearest Huck International location (see International, Inc. for evaluation.
  • Page 16 8001 Imperial Drive Waco, TX 76714-8117 800-388-4825 254-776-2000 FAX: 254-751-5259 Huck is Forever, For the Long Haul, The regard to properties of the products shown Certified to Future of Fastening Technology, The Future of and/or the means for selecting such products,...

This manual is also suitable for:

3585pt

Table of Contents