Vertex Standard VXR-7000 Service Manual page 11

CWID ANI/ENI: Select the Identifier mode
Double-click the left mouse button to toggle the selec-
tions "CW ID," "ANI/ENI," or "Off." To select this fea-
ture to the "CW ID" or "ANI/ENI," the "CW ID" param-
eter must be enabled via the dealer programming.
Action Mode: Select the repeater operation mode
Double-click the left mouse button to toggle between
"Duplex" operation or "Simplex" operation.
Tx Freq.: Edit Transmit Frequency
Use the [ 0 ] - [ 9 ] keys to enter the desired channel fre-
quency directly, and press the [ E
CTCSS Encoders: Toggle CTCSS Encoder ON/OFF, sets
CTCSS Frequency
Double-click the left mouse
button to display the "Tone Se-
lect" window, click the left mouse
button on the desired tone, then
click the left mouse button on the
[ OK ] switch to accept the select-
ed tone.
DCS Encoders: Toggle DCS Encoder ON/OFF, sets DCS
Code #
Double-click the left
mouse button to display
the "Coded Select" win-
dow, click the left mouse
button on the desired DCS
code, then click the left
mouse button on the [ OK ]
switch to accept the select-
ed code.
Base TOT: Enable/disable the Time-Out Timer while in
the "BASE" station mode
Double-click the left mouse button to toggle the TOT
feature selects "yes" and "no."
The TOT time is determined via dealer programming.
Base Guard: Enable/disable the Base Guard Feature
Double-click the left mouse button to toggle the Base
Guard feature selects "yes" and "no."
When this parameter is set to "yes," the transmitter will
be inhibited for a few seconds before the repeater (in the
"BASE" station mode) turns to receive.
The inhibit time is determined via dealer programming.
VXR-7000 VHF Service Manual
] key.
NTER
Operating Manual Reprint
LOUT: Select the Lock Out Feature's mode
Double-click the left mouse button to toggle the Lock
Out Feature between "BCLO," "BTLO," or "off."
"BCLO" inhibits transmitting while there is carrier
present. "BTLO" inhibits transmitting while there is car-
rier present unless there also is a valid tone present.
TX Pwr: Transmitter Power Output Selection
This parameter selects the desired power output from the
VXR-7000 on the current channel. The available values
are HIGH and LOW.
Double-click the left mouse button to select "Hi" or
"Lo."
TOT Mute: Enable/disable the TOT (Time-Out Timer)
beep monitoring
Double-click the left mouse button to toggle the TOT
Mute feature selects "on" or "off."
When this parameter is set to "on," the alert beep will
sound from the front panel speaker before the repeater
turns itself off.
Rpt Use: Enable/disable the Time-Out Timer while oper-
ating in the repeater mode
Double-click the left mouse button to toggle the Re-
peater TOT selects "yes" or "no."
The TOT time is determined via dealer programming.
TOT Beep: Enable/disable the TOT beep Transmission
Double-click the left mouse button to toggle the TOT beep
selects "yes" or "no."
When this parameter is set to "yes," the alert beep will
be sent out on the air before the repeater turns itself off,
while oprtating in the "REPEATER" mode.
RPT HT: Enable/disable the Repeater Hang-on Timer
Double-click the left mouse button to toggle the Re-
peater Hang-on Timer selects "yes" or "no."
When this parameter is set to "yes," the repeater will
remain keyed for a desired seconds after a receiving car-
rier is dropped.
The Hang-up time is determined via dealer program-
ming.
RPT GT: Enable/disable the Repeater Guard
Double-click the left mouse button to toggle the Re-
peater Guard feature selects "yes" or "no."
When this parameter is set to "yes," the transmitter in-
hibit few second before the repeater is unkeyed.
The inhibit time is determined via dealer programing.
11