1. Manuals
  2. Brands
  3. ICP DAS USA Manuals
  4. Wireless Router
  5. WF-2051
  6. Quick start manual

ICP DAS USA WF-2051 Quick Start Manual

Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
「 WF-2051」Package Checklist
The package includes the following items:
One WF-2051 module
One Quick Start
One software utility CD
One screw driver
One RS-232 cable (CA-0910)
One Antenna 2.4GHz - 5 dBi (ANT-124-05)
Note:
1.
If any of these items are missed or damaged, contact the local distributors
for more information. Save the shipping materials and cartons in case you
want to ship in the future.
2.
This document supports the RevB version for the WF-2051 module. For
the previous version, please refer the v1.x version quick start on the CD.
Appearance and pin assignments
Figure 1: Appearance of the WF-2051
WF-2051 Quick Start RevB1.0 2016/10

Quick Start

1/8

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WF-2051 and is the answer not in the manual?

Questions and answers

Related Manuals for ICP DAS USA WF-2051

Summary of Contents for ICP DAS USA WF-2051

  • Page 1: Quick Start

    Save the shipping materials and cartons in case you want to ship in the future. This document supports the RevB version for the WF-2051 module. For the previous version, please refer the v1.x version quick start on the CD.

  • Page 2: Hardware Connection

    WF-2051 Quick Start RevB1.0 2016/10 Figure 2: I/O Connector of WF-2051 Table 1: Power/Signal Connector Power/Signal connector Pin Assignment Description Frame Ground +10 ~ +30 VDC Power / RS-232 GND RS-232 RxD RS-232 TxD Table 2: Operating Mode Selector Switch...
  • Page 3 WF-2051 Quick Start RevB1.0 2016/10 Figure 3: Power and Serial port wire connection I/O connection Figure 4: DI Dry contact wire connection Figure 5: DI Wet contact wire connection...

  • Page 4: Installation

    WF-2051 Quick Start RevB1.0 2016/10 Installation Before use, associated hardware configuration, the steps described as follows： Step 1: Checking the WF-2000 series firmware operation mode It needs to set the DIP switch to the "OP" position (operation mode), as resetting the power, WF-2000 series will be in the operation mode.
  • Page 5 1 and 254 except 1, Subnet mask as "255.255.255.0". Finally, press "OK" button. 02、Wireless network connection : a. View available wireless networks and you can see the "WF-2051" wireless network in the list. b. Select the "WF-2051" and press the "Connect" button.
  • Page 6 WF-2051 Quick Start RevB1.0 2016/10 Access I/O data 01、Connection with Modbus TCP utility a. Open Modbus TCP utility and key in the IP address as "192.168.255.1", Port as "502". Finally, click the "Connect" button. Figure 9: Modbus TCP utility Connection interface b.
  • Page 7 WF-2051 Quick Start RevB1.0 2016/10 WF-2051 I/O Address Mapping Table 3: (0xxxx) DO address Begin Address Points Descriptions Range Access Type Clear 00011 1=Clear High Speed Counter Clear 00021 1=Clear Low Speed Counter Table 4: (1xxxx) DI address Begin Address...

  • Page 8: Technical Support

    WF-2051 Quick Start RevB1.0 2016/10 Troubleshooting Item Problem Description Solution Power Failure 1. Please return to the ICP DAS for inspection and (PWR LED Off) repair 1. Make sure that the service set identifier device (SSID) settings are the same.

Table of Contents