Holzstar ADH 200 Instruction Manual

Holzstar ADH 200 Instruction Manual

Planer-thicknesser
Hide thumbs Also See for ADH 200:

Advertisement

Instruction manual
Planer-Thicknesser
ADH 200
ADH 250
ADH 305
ADH 200
ADH 250

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ADH 200 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Holzstar ADH 200

  • Page 1 Instruction manual Planer-Thicknesser ADH 200 ADH 250 ADH 305 ADH 200 ADH 250...
  • Page 2: Table Of Contents

    1 Introduction .............3 Product identification 1.1 Copyright ............3 Planer-Thicknesser Item No. 1.2 Customer service..........3 1.3 Disclaimer............3 ADH 200 5905200 2 Safety................3 ADH 250 5905250 2.1 Legend of symbols ..........3 2.2 Operator responsibility ........4 ADH 305 5905305 2.3 Operating staff qualification .......
  • Page 3: Introduction

    All data in this operation manual has been compiled on You have made an excellent choice in purchasing a the basis of the state-of-the-art, valid standards and HOLZSTAR Planer-Thicknesser. guidelines as well as our many years of expertise and experience.
  • Page 4: Operator Responsibility

    Safety at the machine's installation location. Said risk as- sessment shall be reflected in operating instruc- ATTENTION! tions for machine operation. This combination of symbol and signal term indica- - During the entire machine operating time opera- tes a potentially hazardous situation which may tors must check whether the operating instructions cause minor or light injuries if it is not averted.
  • Page 5: Personal Protective Equipment

    Safety resulting from improper behaviour. Tasks which go bey- ond normal operation may only be carried out by the Safety boots operator if they are listed in the operation manual and the operator has made him/herself familiar with them. The safety boots protect the feet against crushes, falling parts and slipping over on slippery under- Qualified electrician: ground.
  • Page 6: General Safety Aspects

    Safety 2.7 General safety aspects 9. Use protective equipment. - Use safety glasses. Note the following: - Use face or dust mask if cutting operations create dust. 10. Don't abuse cables. WARNING! When using electric tools, basic safety precautions - Never carry tool by cable or rank it to disconnect it should always be followed to reduce the risk of fire, from socket.
  • Page 7: Designated Use

    Designated use 19. Stay alert. 30. Tools equipped with chip collection and extractor hoods shall be connected to the dust and chip-coll- - Watch what you are doing, use common sense ecting device. and do not operate the tool when you are tired. 31.
  • Page 8: Technical Data

    Technical Data Technical Data 4.1 Type plate Model ADH 200 ADH 250 ADH 305 Electrical 230 V / 230 V / 230 V / connection 50Hz 50Hz 50Hz Motor output 1,5 kW 1,5 kW 1,8 kW Speed 8500 8500 8500 Number of Fig.
  • Page 9: Machine Description

    B Clamping segment eral comprehension and may deviate from the actual type. C Planer D Spring E Bearing 6.2 Scope of supply ADH 200 - Planing machine - Chip extraction hood - Jointer fence - Tube - Dust bag - Instruction manual ADH 250 / 305 Fig.
  • Page 10: Installation Of The Planer-Thicknesser

    ATTENTION! Consider the weight of the machine! Fig. 5: Hole separation ADH 200 / ADH 250 / ADH 305 The machine may be installed only by two persons. Check the tools corresponding to sufficient dimen- Mounting of the parts sioning and load carrying capacity.
  • Page 11: Operation

    - Disconnect the mains plug before you start any In a planing can be reached out a depth up to 2 mm works on the machine. (ADH 200 , ADH 305) or 3 mm (ADH 250). This depth may be reached only by: WARNING!
  • Page 12 Operation Fig. 8: Adjustment of the knife shaft cover Fig. 6: Installation of the chip extraction hood Step 5: Power the machine on with the green ON switch. Step 2: Set the angle fence on the desired height with handle assembly at spindle with reference to Step 6: Press the workpiece with one hand against the Infeed table and angle fence.
  • Page 13: Thicknessing

    Operation 8.2 Thicknessing Step 1: Make sure that the machine is switched off and disconnected from the power supply. Step 2: Disassemble the side fence and tilt the knife shaft cover to the rightmost position Step 3: Raise the knife shaft cover [Pos. P, Fig. 11] to the highest position Step 4: Disassemble you the dust extraction hose.
  • Page 14: Workflow

    Operation Step 1: Disconnect the Planer-Thicknesser from power. Step 4: Turn the planer shaft and place the knife to the height of the surface B. Tighten the screws of the planer again. Check the height by rotating the planer shaft again. The knife should touch lightly the surface B.
  • Page 15: Care, Maintenance And Overhaul/Repair

    Care, maintenance and overhaul/repair Care, maintenance and overhaul/re- 9.2 Maintenance and repair pair Maintenance and repair work may only be carried out by qualified personnel. DANGER! Should the Planer-Thicknesserdoes not work properly, Electric shock is life-threatening! contact your dealer or our customer service. Contact There is a danger of life in case of contact with cur- details can be found in chapter 1.2 Customer.
  • Page 16: Troubleshooting

    Troubleshooting 10 Troubleshooting Malfunction Possible cause Remedy Engine does not start Power supply is Check the power connection by ex- ON/OFF Switch is defective. pert staff. Protektive switch is ON Cool the motor, then restart The motor is runnig, but planer knife The driving is torn Replace the drive belt.
  • Page 17: Electric Circuit Diagram

    167 on the spare parts drawing. - Type of machine: Planer-Thicknesser ADH 250 - Article number: 5905250 Abb. 16: Electric circuit diagram ADH 200, ADH 250, ADH 305 - Position number: 167 13 Spare parts The order No. is: 0-5905250-17 The order No.
  • Page 18: Spare Parts Drawings

    The following drawings are intended to help in case of service, to identify necessary spare parts. To order send a copy of the parts drawing with marked components to your dealer. Fig. 17: Spare parts drawing ADH 200 ADH-Series | Version 1.05...
  • Page 19 Spare parts Fig. 18: Spare parts drawing ADH 250 ADH-Series | Version 1.05...
  • Page 20 Spare parts Fig. 19: Spare parts drawing ADH 305 ADH-Series | Version 1.05...
  • Page 21: Ec Declaration Of Conformity

    As per machine directive 2006/42/EC, Appendix II 1.A Stürmer Maschinen GmbH Manufacturer / distributor: Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt hereby declares that the following product Holzstar® Woodworking machines Product Category: Planer-Thicknesser Machine typ: Designation of the machine: Article number: ADH 200...
  • Page 22 www.holzstar.de...

This manual is also suitable for:

Adh 250Adh 305

Table of Contents