Table of Contents
Advertisement
Quick Links
DH100-CT
Sliding Pedestrian Door Motion & Presence Sensor
NOTE: Set up for this sensor should be
performed by an AAADM-certified installer.
Section 1
General Description
The DH100-CT is an active infrared presence sensor that
is designed to provide both activation and safety
detection for automatic sliding and folding doors in a
single device.
• Test Input provides sensor monitoring
capabilities as required by the latest
industry standard.
• Pattern depth and width are
adjustable using mounting height,
dip switches, detection area depth,
and detection area width adjustments.
• Frequency can be changed to prevent interference
from other sensors in close proximity.
• Self-Diagnostic means the sensor continuously
monitors itself.
• Monitor Mode Switch ensures against false operation
caused by snow, leaves, insects, etc.
• Programmable Presence Timer (2 sec., 30 sec.,
60 sec., or infinity).
Section 2
Parts Identification
Potentiometer
(Sensitivity Volume)
Connector
Depth Adjustment
Lever Arm
(Inner 3 Rows)
Indicator LED
Area Mask
(Red, Green & Blue)
(Inner 3 Rows)
Accessories
Mounting Template
Installation
Instruction
Cover
Depth Adjustment
Lever Arm
(Outer 2 Rows)
Dip Switch
Y
Dip Switch
X
Area Mask
(Outer 2 Rows)
Detection Window
Cable
Mounting Screws
(2 pcs.)
7898 Zionsville Road Indianapolis, Indiana 46268
Telephone: (317) 842-2545 www.mssedco.com custsvc@mssedco.com
Section 3
Mounting Information
1. Do not mount higher than 9.84 ft. (3m).
2. Mount within 50mm (1.97") from bottom of header
cover.
3. Do not leave any objects which may move in the
detection pattern.
4. Avoid steamy environments.
5. Ensure rain or snow will not fall directly on unit.
6. Ensure snow or water can not accumulate on floor.
7. Ensure a minimum of reflected sunlight from the
floor.
8. Use different frequency settings for sensors in close
proximity.
1
3.0m
(9.84ft)
6
5
To maximize the effectiveness of doorway detection,
install the DH100-CT outside and inside as shown
below.
Base
Side View
A
INSTALLATION INSTRUCTIONS
2
3
Max 50mm
(1.97")
4
3
7
Use Alternate Frequency.
A
B
Plan View
B
A
Moving Door Leaf
B
(/MANU) DH100-CTv1017
Moving Door Leaf
Page 1
Advertisement
Table of Contents
Related Manuals for MS Sedco DH100-CT
Summary of Contents for MS Sedco DH100-CT
-
Page 1: General Description
Section 1 cover. General Description 3. Do not leave any objects which may move in the The DH100-CT is an active infrared presence sensor that detection pattern. is designed to provide both activation and safety 4. Avoid steamy environments. detection for automatic sliding and folding doors in a 5. -
Page 2: Mounting And Wiring
DH100-CT INSTALLATION INSTRUCTIONS Sliding Pedestrian Door Motion & Presence Sensor Section 4 Replace cover. Mounting and Wiring 1. Using the mounting template Depth Adjustment provided, drill mounting and Lever Arm 50mm wire holes. NOTE: Be careful not to inadvertently move the Depth Adjustment Lever Arms when replacing the cover. - Page 3 DH100-CT INSTALLATION INSTRUCTIONS Sliding Pedestrian Door Motion & Presence Sensor Test Input Setting from Door Controller: When connected to a door controller without a TEST input, set 1 2 3 4 5 6 to “OFF”. When connected to a door controller with a TEST input, set to “ON”.
- Page 4 “Doorway Learn” process. Red solid LED Presence Detection: During the “Doorway Learn” process, the outer 4 rows of detection on the DH100-CT sensor switch from motion detection to presence detection 10 seconds after power ON. The inner “Doorway Learn”...
- Page 5 DH100-CT INSTALLATION INSTRUCTIONS Sliding Pedestrian Door Motion & Presence Sensor Section 7 Detection Area Depth Adjustment: Outer 2 Rows Adjusting Detection Pattern Outer 2 rows adjustment Detection Area Depth Adjustment: Inner 3 Rows lever arm Inner 3 rows adjustment lever arm 9.8’...
-
Page 6: Verification Of Operation
DH100-CT Sliding Pedestrian Door Motion & Presence Sensor INSTALLATION INSTRUCTIONS Section 9 Section 11 Verification of Operation Troubleshooting PROBLEM 1: Door does not open when person enters 1. After mounting, setting parameters and applying the detection area. power, walk test unit to verify detection pattern. -
Page 7: Technical Data
Weight....... 0.55 lbs. (0.25kg) Color........Black Section 12 Accessories....... Cable, Mounting Screws, Technical Data Mounting Template, Installation Model........ DH100-CT Combination Motion Instructions & Presence Sensor Detection Method..... Floor Reflection Method (FRM) Active Infrared Max. Installed Height..9.84 ft. (3.0m) Pattern Adjustments..Pattern Depth (2 to 5 rows via... -
Page 8: External Dimensions
Warranty MS SEDCO guarantees this product to be free from manufacturing defects for 3 years from date of installation. Unless MS SEDCO is notified of the date of installation, the warranty will be in effect for 3 years from the date of shipment from our factory. If, during the... - Page 9 DH100-CT INSTALLATION INSTRUCTIONS Sliding Pedestrian Door Motion & Presence Sensor 7898 Zionsville Road Indianapolis, Indiana 46268 Page 9 Telephone: (317) 842-2545 www.mssedco.com custsvc@mssedco.com (/MANU) DH100-CTv1017...
Need help?
Do you have a question about the DH100-CT and is the answer not in the manual?
Questions and answers