Advertisement
ImproX (TT) Twin Antenna Terminal
SPECIFICATIONS
Read/Write Capability ..................
Working Environment
Open Frame Construction ......
(XTT900)
Aluminium Extruded Cabinet ..
(XTT910)
Power Supply Combo ............
(IPS910)
Open Frame Construction (XTT900) and Aluminium Cabinet (XTT910)
Input Voltage ................................
Power Requirements
Input Voltage 10 V DC ...........
Input Voltage 30 V DC ...........
I
MPRO
INSTALLATION MANUAL
Impro Tags: Slim Tags (Read Only), Omega
Tags (Read Only), WriTag 128 (Read/Write)
and WriTag 2048 (Read/Write).
HID 125 kHz Tags. (Read Only).
NOTE:
Designed to work in an indoor (dry)
environment. The Terminal is not sealed
against water.
Designed to work in an indoor (dry)
environment, similar to IP40. The Terminal is
not sealed against water.
Designed to work in an indoor (dry)
environment similar to IP20. The Power
Supply Combo is not sealed against water.
10 V DC to 30 V DC, polarity sensitive.
Current (mA)
180
60
MODEL NUMBER: XTT900-1-0-GB-XX
X TT
HID is a registered trademark of
HID Global Corporation (an ASSA
ABLOY Group Brand).
XTT910-1-0-GB-XX
XTT911-0-0-NN-XX
IPS910-1-0-GB-XX
Power (W)
1.8
1.8
Advertisement
Table of Contents
Related Manuals for impro IMPROX TT
Summary of Contents for impro IMPROX TT
-
Page 1: Specifications
MPRO ImproX (TT) Twin Antenna Terminal INSTALLATION MANUAL SPECIFICATIONS Read/Write Capability ....Impro Tags: Slim Tags (Read Only), Omega Tags (Read Only), WriTag 128 (Read/Write) and WriTag 2048 (Read/Write). HID 125 kHz Tags. (Read Only). NOTE: HID is a registered trademark of HID Global Corporation (an ASSA ABLOY Group Brand). - Page 2 Height ........99 mm (4 in) (Max) including the terminals. Charge Voltage ...... 13.8 V DC. The following specifications are common to all models of the ImproX TT: Relays Relay Output ......2 Independent, single-pole, double-throw (SPDT) Relays, each with NO, COM and NC contacts.
-
Page 3: Installation Information
Relays (1 and 2) ..... Continuous Red on activation of the Relay. INSTALLATION INFORMATION Accessories Find the following when unpacking the ImproX TT Terminal: CAUTION: DO NOT use the Metal-oxide Varistors (25 Vrms, 500 A, 77 V max clamping) with mains power applications. - Page 4 ImproX TT Terminals can be mounted alongside each other. EARTH Connection Connect the ImproX TT Terminal to a good EARTH point. Using the RS485 Port, connect the EARTH Lead to the „ ‟ Terminal. Mains EARTH can be used, but electrical noise may exist.
- Page 5 Make certain that you mount the Terminal on a vibration-free surface. NOTE: The ImproX TT can be mounted onto virtually any surface including metal. Select the mounting position of the ImproX TT Terminal, considering accessibility, routing of wires and visibility of the LEDs.
- Page 6 End Plates. Swivel the screwdriver until the Top Cover makes a click sound. Insert the screwdriver in the gap (on the side of the ImproX TT) between the Top Cover and the Base. Swivel the screwdriver again, to release the Top Cover from the Base.
- Page 7 Use the supplied Connection Leads for the low voltage connections to the Power Supply Combo. Using the supplied Quick Click Glands or Gland Breakouts, neatly lead the wires out of the Cabinet. Blank Space XTT300-0-0-GB-16 January 2011 Page 7...
-
Page 8: Electrical Connections
ELECTRICAL CONNECTIONS Power Supply Combo (IPS910) Layout Figure 5: Layout Diagram – Power Supply Combo XTT300-0-0-GB-16 January 2011 Page 8... - Page 9 Connecting the ImproX TT Terminal Figure 6 shows a detailed electrical connection diagram for the ImproX TT Terminal. Figure 6: Typical ImproX TT Terminal Electrical Connections XTT300-0-0-GB-16 January 2011 Page 9...
- Page 10 Settings Specific to the Power Supply Combo WARNING: DO NOT REMOVE THE PLASTIC COVER PROTECTING THE SWITCH MODE POWER SUPPLY. REMOVING THE COVER PUTS YOU AT RISK OF ELECTRICAL SHOCK. CAUTION: DO NOT exceed the Input Voltage specified. Wiring the Mains Input Power Cord DO NOT TOUCH ANY PART OF THE CIRCUIT ONCE YOU’VE WARNING: APPLIED POWER TO THE POWER SUPPLY COMBO.
- Page 11 Insert the wire. Release the Push-button. Repeat steps 1 to 3 for each connection. Attach a suitable Mains Input Power Plug using the following connections: Live (Brown) Neutral (Blue) Earth (Yellow/Green) Close the Lid of the Cabinet. Fuse Information Fuse Type Purpose...
-
Page 12: Guarantee Or Warranty
10. Reconnect the mains power supply to the Power Supply Combo. ImproX TT Address Information Each ImproX TT Terminal is, in fact, two Terminals in one. The first “Terminal” Fixed Address is associated with Reader [1], and the second with Reader [2]. -
Page 13: User Notes
USER NOTES XTT300-0-0-GB-16 January 2011 Page 13... - Page 14 USER NOTES XTT300-0-0-GB-16 January 2011 Page 14...
- Page 15 USER NOTES XTT300-0-0-GB-16 January 2011 Page 15...
- Page 16 This manual is applicable to the ImproX (TT) Twin Antenna Terminal, XTT900-1-0-GB-05, XTT910-1-0-GB-03, IPS910-1-0-GB-02 and XTT911-0-0-NN-00. (The last two digits of the Impro stock code indicate the issue status of the product). ImproX TT\English Manuals\LATEST ISSUE XTT300-0-0-GB-16 Issue 17 Jan 2011 \ImproXTT-insm-en-17.docx...