1. Manuals
  2. Brands
  3. Sony Manuals
  4. Security Camera
  5. CCD-PC1
  6. Service manual

Sony CCD-PC1 Service Manual

Hide thumbs Also See for CCD-PC1:
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
System
NTSC color, EIA standards
Video signal
Image
device
Lens
Approx. '/IS in (10 mm)
Macro
Minimum
illumination
9 lux
Illumination
range
9 to 10,000 lux
White
balance
Auto
Iris
Manual
Electronic
shutter
Focus
adjustment
Manual
General
Power
requirements
DC 6.OV
Power
consumption
1.8 w
Video
output
1 Vp-p, 75Q unbalanced, sync
negative
S video output 4-pin mini DIN
Audio
output
Output 327 mV (monaural),
impedance less than 2.2 k.Q
Operating
temperature
41°F to 104°F (5°C to 4O'C)
Storage
temperature
-4°F to 140'F (-20°C to +hO"C)
SPECIFICATIONS
Dimensions (w x h x d)
Mass
Microphone
DC jack
Supplied accessories
AC power adaptor (AC 12OV,
Audio/video
cable
Operating
instructions
Design and specifications are subject to change
without
notice.
US Model
Base: approx. 3 5/n x 1 '"/v x 5 '/q
in (91 x 45 x 132 mm)
Camera: approx. 1 x '/N x 2 '/8 in
(25 x 22 x 73 mm)
Arm length: approx. 11 I/J in (285
m m )
Approx. lib 7 oz (650 g)
Monaural
6.0 V
60 Hz) (1)
(1)

Advertisement

Table of Contents
loading

Related Manuals for Sony CCD-PC1

Summary of Contents for Sony CCD-PC1

  • Page 1 SERVICE MANUAL US Model SPECIFICATIONS System Dimensions (w x h x d) Base: approx. 3 5/n x 1 ‘“/v x 5 ‘/q NTSC color, EIA standards Video signal in (91 x 45 x 132 mm) Image device Camera: approx. 1 x ‘/N x 2 ‘/8 in Lens (25 x 22 x 73 mm) Approx.

  • Page 2: Table Of Contents

    A N D I N T H E P A R T S L I S T A R E C R I T I C A L T O S A F E REPLACE THESE COMPONENTS WITH O P E R A T I O N . SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN THIS MANUAL SUPPLEMENTS PUB- LISHED SONY.

  • Page 3: Service Note

    SERVICE NOTE LOCATION t h i s s e r v i c e m a n u a l , t h e m o u n t e d l o c a t i o n s o f t h e semiconductors (IC, transistor, diodes) are indicated in red in s c h e m a t i c d i a g r a m s .
  • Page 4 CCD-PC1 English Sony Corporation 951027022-l Printed in S$w;; Consumer A&V Products Company P e r s o n a l A & V P r o d u c t s D i v . 9-960420-I 1 by Homo A&V Products Div.

  • Page 5: General

    SECTION 1 This section is extracted from GENERAL instruction manual. Precautions Maintenance the lens with a blower brush 10 If thaw arc fingerprints “n it, body with a dry soft cloth, or a Soft cloth lightly Precaution on copyright which may damage the finish.

  • Page 6: Disassembly

    CCD-PC1 SECTION 2 DISASSEMBLY : Follow the disassembly procedure in the numerical order given. Note 2-1. REMOVAL OF HEAD CABINET (UPPER, LOWER) AND CD-144 BOARD 2-2. REMOVAL OF OPTICAL FILTER BLOCK AND CCD BLOCK ASSY : The optical filter block has a front and a...

  • Page 12: Cd-144 Board

    SECTION 5 REPAIR PARTS LIST EXPLODED VIEW 5-I. NOTE : Accessories and pad . Items marked “ * “are not stocked since given in the last of thl is parts list. they are seldom required for routine they may have some difference from the service.

  • Page 13: 5-2. Electrical Parts List

    5-2. ELECTRICAL PARTS LIST NOTE : Items marked “ * “are not stocked since Due to standardization, replacements in they are seldom required for routine the parts list may be different from the service. Some delay should be antici- parts specified in the diagrams or the pated when ordering these items.
  • Page 14 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C515 I-164-360-11 CERAMIC CHIP 1-774-372-21 PIN, CONNECTOR (PC BOARD) 13P 0. 1uF 1 6 V l-580-055-21 PIN, CONNECTOR 2P 0. 1uF 1 6 V C524 l-135-091-00 TANTAL. CHIP 2 0 % 1 6 V 0.
  • Page 15 Description Remark Ref. No. Part No. Description Remark 4503 8-729-230-63 TRANSISTOR Q504 8-729-420-24 TRANSISTOR 2SB1218A-QRS TRANSISTOR JACK, DC ( UNIFIED RITY 3551 1-566-849-11 CONNECTOR, (S) TERMINAL 4P (S-VIDEO) 1-216-845-11 METAL CHIP l-580-441-31 JACK, PIN 2P (VIDEO/AUDIO OUT) R102 1-216-841-11 METAL CHIP 47K 5% R104 l-216-807-11 METAL CHIP...
  • Page 16 Part No. Description Remark Ref. No. Part No. Description Remark R332 1-218-875-11 METAL CHIP 15K 0.50% 1/16W R530 1-216-841-11 METAL CHIP 47K 5% R333 1-216-819-11 METAL CHIP R531 1-216-841-11 METAL CHIP 47K 5% R334 1-216-864-11 METAL CHIP R532 1-216-821-11 METAL CHIP R335 1-218-847-11 METAL CHIP 0.50% l/168 R533 1-216-825-11 METAL CHIP...
  • Page 17 Ref.No. Part No. Description Remark Ref. No. Part No. Description Remark < VIBRATOR > ACCESSORIES & PACKING MATERIALS Xl01 l-760-458-21 VIBRATOR, CRYSTAL (32kHz) X401 l-760-320-11 VIBRATOR, CRYSTAL (28.6363MHz) l-574-039-11 CORD, CONNECTION (For AV monaural) X501 l-760-081-21 VIBRATOR, CERAMIC (24MHz) l-693-031-11 ADAPTOR, AC (AC-64NC) 3-800-369-11 MANUAL, ImRUCTION (ENGLISH) 3-966-445-01...

  • Page 18: Adjustments

    CCD-PC1 SECTION 6 ADJUSTMENTS When performing adjustments, refer to the layout diagrams for adjustment related parts beginning from the page 6-20. 6-1. CAMERA SECTION ADJUSTMENTS PREPARATIONS BEFORE ADJUSTMENT l-l. (CAMERA SECTION) l-l -1. List of Service Tools Vectorscope Oscilloscope Stabilized power supply...

  • Page 19: Adjusting Remote Control Unit

    [Setting of Connect] : For further details on how to remove the cabinet and each Note board, refer to “2. Disassembly”. 1) Connect the equipments for adjustments as shown in Fig. 6-l-2. Adjusting remote control unit VIDEO jack Extension cord (J-6082-084-A) SW OFF(OPEN) S t a b i l i z e d...
  • Page 20 -3. Precautions 3. Subject 1. Switch setting 1) Camera power ON / OFF ..........ON 1) Color bar chart (Standard picture frame) Adjust the display frame as shown in Fig.
  • Page 21 l-l-4. Adjusting Remote Control Unit Changing the address The address will increase when the FF ( )) ) button is The adjusting remote control unit is used for rewriting the pressed, and decrease when the REW ( 44 ) button is pressed. adjustment data written in the non-volatile memory necessary for performing the adjustments.
  • Page 22 l-l -5. Page F Address List The data listed in the adjustment data memo column are N o t e 1 fixed values. The adjustment data initial values are the values -after Note 2 performing “Page F Data Initialization” and “Page F Data Modification”.
  • Page 23 Adjustment data Adjustment data A d d r e s s Memo Memo I n i t i a l v a l u e column v a l u e column Not used II ‘ 4 8 I 00 II B3 I 25 I Not used Table 6-l-2.
  • Page 24 The calculation of the adjusting remote control unit display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data. Table 6-l-3.
  • Page 25 When in above range (3) of 4096 to 65536. [DECIMAL TO HEX CONVERSION METHODS] 1) Divide the base 10 (decimal) data by 4096. Set that result as The conversion method differs according to the range of the number you want to convert. “A”.

  • Page 26: Camera Syetem Adjustment

    CAMERA SYSTEM ADJUSTMENT 1-2. l-2-2. Power Supply Voltage Check (VC-173 board) l-2-1. Cautions when making adjustments after’ changing major components. Subject Option When the imager or the lens block has been replaced, you must adjust the items on the following table marked with an “ 0 “. Measuring instrument Digital voltmeter ”...

  • Page 30: Adjustments Setup

    l-2-4. D Page Data Settings Adjusting method : Procedure Conditions Sequence I co Press the PAUSE button after setting the data. Press the’PAUSE button after setting the data. Press the PAUSE button after setting the data. Press the PAUSE button. :.When data has been written into the D page, turn the power off once, and then back on again.
  • Page 31 l-2-6. Page F Data lnitlalization Note 1 : Complete readjustment of the camera section is required when initialization of F page data has been performed. Note Initialization procedure Sequence Press the PAUSE button after setting the data. e data initialization Handling after adjustment is complete Sequence Page Address...
  • Page 32 When adjustments are off (incomplete), image synch will waver and the color won’t match. Subject Not required Measurement point Pin @I of 104 Measuring instrument Frequency counter Adjustment page Adjustment address 05 Specified value Adjusting method : Sequence Page Address Data Procedure Conditions...

  • Page 33: Sub Adjustment (Vc-173 Board)

    1-2-8. V SUB Adjustment (VC-173 board) When adjustments are off, and the target object is shown under high brightness, the image may become blurred or fuzzy. Subject Not required Not required Measurement point Not required Measuring instrument Adjustment page Adjustment address 04 Adjusting method : Procedure Conditions...

  • Page 34: Pictureframesetting

    l-2-9. Picture Frame Setting Subject Color bar chart standard picture frame VIDEO output terminal (5552-l) Measurement point Measuring instrument Setting method : Move the camera and set the reference Image. Display an image of the color bar chart, that is stable and Confirm on the Oscilloscope TV monitor picture frame Color bar chart picture frame...

  • Page 35: L-2-10. Entering Reference Data For The Auto White

    l-2-10. Entering Reference Data for the Auto White Balance Standard Data Subject White pattern standard picture frame Measurement point White pattern standard picture frame Adjustment page Adjustment address OE (BG3200 H), OF (BG3200 L) Adjusting method : Address Data Procedure Conditions Sequence Page ON/OFF the main power supply (6V).

  • Page 36: L-2-11. Color Reproduction Adjustment

    1-2-l 1. Color Reproduction Adjustment When adjustment is off, the color restoration will be poor. Subject Color bar chart standard picture frame Measurement point Vectorscope, Measuring instrument Color bar chart standard picture frame Adjustment page OA IB-Y HUE) OB (R-Y HUEj Adjustment address 2F (B-Y GAIN)
  • Page 37 Handling after adjustments are complete Sequence Press the PAUSE button after setting the data. Close. FOR CAMERA COLOR REPRODUCTION ADJUSTMENT make Please a photo copy from this chart. CCD-PC1 6-17...

  • Page 38: Auto White Balance Adjustment

    1-2-l 2. Auto White Balance Adjustment When adjustment is off, the color restoration for the white balance will be poor. Subject I White pattern standard picture frame Filter Cl4 for color temperature correction Filter Adjusting remote control : Measurement point LCD display (Page A) White pattern standard picture frame, Measuring...

Table of Contents