Summary of Contents for Made4.pet BC-2
- Page 1 Smart bark control collar BC-2 User manual Important: Read this manual carefully before using the Smart Bark Control Collar for the safety of you and your dog.
- Page 2 Welcome to the Family! Thank you for choosing made4.pet! We at made4.pet are dog owners just like you and bark collars just like yours helps us train our beloved pets quickly and safely. We want your new collar to help you enjoy every minute you and your family have with your dog.
-
Page 3: Table Of Contents
Table of Contents Introduction Major features Warning/Safety precautions Package Content Controls and settings Getting Started Installing the battery Test #1 (ON/OFF) Test #2 (functional) Strap length and collar placement Adjusting the sensitivity level Before you start training How do the training programs work FAQ and troubleshooting... -
Page 4: Introduction
Introduction Smart Bark Control Collar stops your dog from barking by detecting its bark and delivering progressively increasing shock you control. There are 2 training programs: • GREEN training program delivers progressively increasing beeping sounds and vibrations in 4 stages. It is recommended to start training with this program;... -
Page 5: Warning/Safety Precautions
Warning/Safety precautions 1. The attached printed instruction manual is out of date, please use this PDF copy to operate the device properly. 2. Do not allow your dog to chew on this collar. You should also attempt to minimize scratching or clawing at the casing of the unit. 3. -
Page 6: Package Content
Package Content Check it right after you’ve received the package! The printed paper instruction manual found in the package is out of date. Please use this PDF copy for updated instructions. -
Page 7: Controls And Settings
Controls and settings LCD indicates the current sensitivity level. LCD will automatically turn off after 10 VOX+ seconds to save power. button LCD will indicate flashing “L” if the battery is low. Please install a fresh one. SET/POW button Put electrodes and the appropriately sized silicone protective caps on the prongs before LED indicates the current training program: you start using the device... -
Page 8: Getting Started
Getting Started Installing and removing the battery (type Alkaline 4LR44 6V) 1. Open the battery door located on the front side of the unit. 2. Place the negative end of the battery against the coil (spring) in the device. Push the battery towards the coil to insert the battery then push the positive end downward to the clip to fully insert the battery. -
Page 9: Strap Length And Collar Placement
Getting Started Imitate “barking” by shouting “HOW” or “WOW” right into the bark detector hole. Do it loudly and do not hesitate. Repeat several times in case the collar does not go off the first time. The collar goes off by beeping and vibrating the first time it detects barking. -
Page 10: How Do The Training Programs Work
How do the training programs work General notes The collar starts the training program each time it detects barking. Each training program consists of sequential stages, meaning a new stage starts immediately after the previous one has completed. A new stage will begin after the previous one if your dog continues barking. If your dog does not continue to bark, the program will not advance to the next stage. - Page 11 How do the training programs work RED training program consists of 6 stages: # 1: Beeps for 3 seconds then vibrates for 5 seconds. No Shock # 2: Beeps for 3 seconds, vibrates for 3 seconds and then delivers shock for 1.5 seconds (weak shock) # 3: Beeps for 3 seconds, vibrates for 3 seconds and then delivers shock for 1.5 seconds (stronger shock)
-
Page 12: Faq And Troubleshooting
In the unlikely event one of our collars is returned, Amazon does not allow made4.pet to run a quality check which may result in missing parts. For this reason, we ask you to check the package content in the very beginning and make sure everything is there. - Page 13 If you’ve followed all of the instructions and performed all of the recommendations and still run into issues please do not hesitate to contact our support team at support@made4.pet. Provide as much information as possible (including photo and video) so we can help...
- Page 14 If for any reason you’re not satisfied let us know so we can make it right! We want to do our best to meet your expectations now that you’re part of the made4.pet family. Send us an e-mail at support@made4.pet if you have any questions or concerns about your made4.pet purchase.