Panasonic SA-HT833VP Service Manual page 19

Display Type of error
CD F 28 DISC loading error
CD F 29 DISC unloading error
CD F 27 DOWN SW error
CD F 22 Mechanism is loading
motor/abnormal
F 03 Traverse servo error
F 04 Tracking servo error
F 05 Seek error
F 06 Power supply error
F 61 Power supply error
10.2.2. Error Code Display
1. Set to DVD/CD mode (Ensure no disc is loaded)
2. While pressing and holding down the [STOP] on main unit and press [0] on remote control in order to display the latest error
code. (Automatically cancelled after five seconds.)
Note: No error code will show if there is no problem with unit. Refer below for error code display.
(Error Code Display)
Section Code
Disc code F103 Illegal Highlight Position
Decoder related F220 Y level adjustment failure
F221 C level adjustment failure
II C error F4FF Compulsory initialization failure (time out)
DSC related F500 DSC error
F501 DSC not ready
F502 DSC time out failure
F503 DSC communication failure
F504 Data slice offset adjustment failure
F505 DSC Attention Error
F506 Invalid media
ODC related F600 Control information unattainable due to demodulation
error
F601 Unknown sector ID requested
F602 LEAD-IN unattainable due to demodulation error
F603 KEYDET unattainable due to demodulation error
F610 ODC failure
F611 6626 QCODE don´t read ERROR
F612 No CRC OK during a certain time of duration
F630 No response to KEY DET makeshift
F631 CPPM KEY DET unavailable to FILE end terminal
F632 CPPM KEY DET unavailable
During the horizontal motion toward to PLAY position, if there is no change when it exceeds the fail
safe timer or if counter direction does not enter into state of target, will be keep it memory mode.
Initialization is done when the next mecha mode starts.
Only when backup data is cleared of this error no. when it compels clearly or power supply start-up.
During the horizontal motion toward opposite direction to PLAY position, if there is no change when it
exceeds the fail safe timer or if counter direction does not enter into state of target, will be keep it
memory mode. Initialization is done when the next mecha mode starts.
Only when backup data is cleared of this error no. when it compels clearly or power supply start-up.
Memory when bottom switch is not changed even if it exceeds it to time of fail safe timer when going
up and down operates toward bottom position. When mechanism begins to operate next time,
initialization is done.
Only when backup data is cleared clearly of this error No. when it compels clearly or power supply
start-up.
Memory at the initialization of mechanism due to abnormality of the loading motor or the mechanism
when entering the state usually cannot. When mechanism begins to operate next time, initialization is
done.
Only when backup data is cleared clearly of this error No. when it compels clearly or power supply
start-up.
Power cannot be turned off due to communication error between panel computer and system
computer.
Abnormal output or power supply abnormal circuit of Power Amp.
Meaning
Description
Possibility of illegal disc when highlight is displayed
Brightness signal level adjustment cannot be properly
operated
Color signal level adjustment cannot be properly
operated
DSC stops due to servo failure. (Startup, focus failure,
etc.)
Communication failure between DSC and system
computer(No communication because DSC does not
move)
See F500.
Communication failure (Result failure occurs after
communication command is transmitted.)
Not in use. (FEP error)
See F500.
Disc is placed upside down; TOC is unreadable or
invalid disc is inserted.
Operation stops because navigation data cannot be
obtained due to demodulation system failure.
Operation stops because access of illegal ID data is
requested.
Unable to read LEAD IN data
Unable to obtain CSS data
No permission of command issue
Unable to obtain seek address at CD system
Unable to obtain ID data at DVD system
(Internal use)
CPPM fail system cannot be read due to scratch.
Revoke or altered.
19
SA-HT833VP
Note