Product Description And Specifications; Operation - Bosch PHG 500-2 Original Instructions Manual

OBJ_BUCH-1348-004.book Page 11 Monday, January 18, 2016 9:46 AM
 Do not use the power tool as a hairdryer. The hot air
being blown out is significantly hotter than that from a hair-
dryer.
 When operating the power tool in damp environments
is unavoidable, use a residual current device (RCD).
The use of a residual current device (RCD) reduces the risk
of an electric shock.
 Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug when
the cable is damaged while working. Damaged cables in-
crease the risk of an electric shock.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Intended Use
The power tool is intended for the forming and welding of
plastic, removal of paint and the warming of heat-shrinkable
tubing. It is also suitable for soldering and tinning, loosening
of adhesive joints and the defrosting of water lines.
Technical Data
Hot Air Gun
Article number
Rated power input
Air flow
Temperature at the nozzle outlet (approx.)
Temperature-measuring accuracy
– at the nozzle outlet
– on the display
Display operating temperature*
Weight according to EPTA-Procedure 01:2014
Protection class
* The display can turn black when not within the operating temperature.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.

Operation

Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Bosch Power Tools
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Nozzle
2 Heat protection collar
3 Standing surface
4 On-/Off switch with air-volume regulator and tempera-
ture control (PHG 500-2/PHG 600-3)
5 On/Off switch with air-volume regulator
(PHG 630 DCE)
6 Button for temperature control (PHG 630 DCE)
7 Display (PHG 630 DCE)
8 Wide jet nozzle*
9 Glass protection nozzle*
10 Reflector nozzle*
11 Welding rod*
12 Welding shoe*
13 Reduction nozzle*
14 Heat-shrinkable sleeve*
15 Angle nozzle*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Noise Information
Noise emission values determined according to EN 60745-1
(no-load operation).
Typically the A-weighted sound pressure level of the product
is lower than 70 dB(A).
PHG 500-2
0 603 29A 0..
W 1600
l/min 240/450 250/350/500
°C 300/500
±10 %
–
°C –
kg 0.75
/II
Switching On
PHG 500-2: Press the On/Off switch 4 to position I or II.
PHG 600-3: Press the On/Off switch 4 to position I, II or III.
PHG 630 DCE: Press the On/Off switch 5 to position I, II
or III.
English | 11
PHG 600-3 PHG 630 DCE
0 603 29B 0.. 0 603 29C 7..
1800 2000
150/300/500
50/400/600 50–630
±10 % ±10 %
– ±5 %
– 0...+50
0.81 0.87
/II /II
1 609 92A 1Z8 | (18.1.16)