Table of Contents
Advertisement
OPERATING INSTRUCTIONS
REFUELLING
Keep the firebox well filled but do not allow fuel to spill over the top
of the fuel retainer.
Logs should be evenly distributed, filling the firebed to give the most
pleasing flame pattern. The air control must be fully opened after
refuelling until the flames are established above the fire. It is best to
refuel on to a hot bed of ash. If at this point the fire starts to die, the
door must be cracked open until the fire is revived. If the fire has
started to die down before refuelling, then more kindling wood must
be added, the air control opened fully and the door cracked open to
re-establish the firebed before adding larger logs (see suitable log
sizes in Specification). This will avoid excessive smoke emission.
Care should be taken that wood does not project over the fuel
retainer or damage to the glass may be caused when the door is
closed. It can also cause the glass blackening of the glass. Maximum
filling height is such that logs cannot fall from the fire when the door
is opened. In smoke controlled areas do not fill the stove above the
level of the air holes in the back bricks, as overloading can cause
excess smoke. Liquid fuels are not to be used on this appliance.
ASH PAN REMOVAL
The ashpan (Bay 5GT) should be emptied regularly before it becomes
too full. Never allow the ash to accumulate in the ashpan so that it
comes in contact with the underside of the grate as this will seriously
damage the grate bars. The ashpan is handled using the tool and
gloves provided. Care should be taken to ensure that ash is cool
before emptying it into plastic liners or bins.
To make ash removal easier there is a special Charnwood ash carrier
available. This may be purchased from your supplier or, in case of
difficulty, directly from Charnwood.
REDUCED BURNING
For reduced burning the fire door must be closed.
When burning wood in areas that are not smoke controlled, load
some large logs on the fire and allow to burn for half an hour before
closing the air control (this will help to reduce tar deposits in the
chimney). Some experimentation may be necessary to find the setting
most suitable for the type of fuel being used and the draw on the
chimney.
To revive the fire, empty the ashpan , riddle the fire, and open the air
control to maximum. When the fire is burning well load on more fuel
as necessary and adjust the air control to the desired setting.
CLEANING AND MAINTENANCE
Cleaning
The Bay VL is finished with vitreous enamel to clean the surfaces
simply wipe over with a dry cloth or soft brush when the appliance is
cold. Abrasive pads and scouring cleaners must not be used as these
will damage the finish. Care should be taken not to knock the enamel
with hard objects as it will chip. The Bay 5 and Bay 5GT are finished
with high temperature paint. Should re-painting become necessary,
high temperature paints are available from your supplier or from
stove shops, or in case of difficulty, directly from Charnwood.
Cleaning the Glass
The glass in the door is a special ceramic glass which is able to
withstand high temperatures. Most deposits on the glass may be
burnt off simply by running the fire at a fast rate for a few minutes. If
it becomes necessary to clean the glass then open the door and allow
it to cool. Clean the glass using a damp cloth and then wiping over
with a dry cloth. Any stubborn deposits on the glass may be removed
with a proprietary stove glass cleaner or ceramic hob cleaner.
Aerosol spray cleaners must not be used near the appliance whilst it
is under fire.
Do not use abrasive cleaners or pads as these can scratch the surface
which will weaken the glass and cause premature failure.
When Not in Use
If the fire is going to be out of use for a long period (for instance in
the summer) then to prevent condensation, and hence corrosion, the
air control should be left fully open and the fire door left ajar. It Is
also advisable to sweep the chimney and clean out the fire. Spraying
the inside of the door and firebox with a light oil, such as WD40, will
also help to keep all internal parts working well.
where the fire has been out of use, the chimney and appliance
flueways should be cleaned before lighting.
Door Seals
For the fire to operate correctly it is important that the door seals
are in good condition. Check that they do not become worn or
frayed and replace them when necessary.
Servicing
It is recommended that the fire is serviced once a year to keep it in
first class working order. After cleaning out the firebox thoroughly,
check that all internal parts are in good working order, replacing any
parts that are beginning to show signs of wear. Check that the door
seals are in good condition and that the door seals correctly.
Repairs or modifications may only be carried out by the Manufacturer
or their approved agents. Use only genuine Charnwood replacement
parts.
8
charnwood
BAY
®
After long periods
Advertisement
Table of Contents
