Content General Notes General Notes This Focus gas appliance is a High Efficiency, Balanced Flue Live Fuel Effect appliance. It provides radiant and convected heat using the latest burner technology. User instructions Before Installation, check that the local distribution conditions, nature of the gas and pressure, and adjustment of the appliance are compatible.
User instructions EMERGENCY GAS ISOLATION Deactivate Functions 1. Install batteries. All icons are displayed and flashing. 2. While the icons are flashing, press the relevant function button and hold for 10 sec. In the event of a gas leak or if gas is smelt, the appliance must be isolated. 3.
Page 4
User instructions Figure 01: 8-symbol Display C. SETTING FAHRENHEIT OR CELSIUS E. CHILD PROOF To change between °C and °F, press buttons simultaneously. To activate press buttons simultaneously. displayed NOTE: Choosing °F results in a 12 hour clock. handset is rendered inoperable, except for the Choosing °C results in a 24 hour clock.
Page 5
User instructions Handset One-Button Operation TO TURN OFF FIRE (Default Setting) · Press Handset button until two short beeps and · Press a blinking series of lines confirms the start button to turn OFF. sequence has begun; release button. · Main gas flows once pilot ignition is NOTE: A new ignition is possible after the OFF confirmed.
Page 6
User instructions H. COUNTDOWN TIMER J. THERMOSTATIC MODE ON/SETTING: 1. Press and hold button until displayed, Press button. displayed, preset and hour flashes. temperature displayed briefly, and then room 2. To select hour press button. temperature displayed. 3. To confirm press button.
Page 7
User instructions Default settings: NOTE: Either continue to PROGRAM 2 and set on and off times or stop ON TIME (Thermostatic) TEMPERATURE: 21 °C (70 °F) programming at this point, and PROGRAM 2 remains deactivated. OFF TIME TEMPERATURE: “ ” (pilot flame only) NOTE: PROGRAM 1 and 2 use the same on (Thermostatic) and off and Daily Timer ( , , , , , , ...
User instructions MANUAL TURN OFF CLEANING AND MAINTENANCE In the event that the appliance needs to be turned OFF manually, This appliance should be inspected and serviced once a year by a qualified, for instance, if the remote control is lost or the batteries become totaly competent and registered person.
(C11). This appliance may only be used with Balanced Flue (otherwise known as Concentric Flue) parts as specified by Focus. The Focus specified flue parts have been approved with the appliance. If the appliance is installed on non-Focus approved parts, Focus cannot guarantee or accept and responsibility for the proper and safe working of the appliance.
Installation instructions E. TERMINAL LOCATIONS Dimension Terminal Position Distance (mm) Directly below an opening, air brick, opening window etc. Above an opening, air brick, opening window etc. Adjacent to an opening, air brick, opening window etc. Below gutters, soil pipes or drain pipes Below eaves Below balconies of car port roof From a vertical drain pipe or soil pipe...
Installation instructions FUEL BED ARRANGEMENTS Curvifocus is available with 2 Grate options, a “Standard Grate” and a “Tear and Deform Grate”. Shown below are these Grate options. These Grate options can all be used in the appliance without any further media.
Installation instructions B. LOG LAY Scatter the Bags of Embers over the top of the burners as shown, keeping the piot area clear. Position Logs C1, C2, & C3 as shown in the diagram. Position Log C4 as shown in the diagram.
Installation instructions COMMISSIONING THE APPLIANCE A. PILOT IGNITION CHECK 1. Ignite the pilot light as described in the User Instructions 2. Check that the pilot flame stays alight 3. Extinguish the pilot light B. MAIN BURNER CHECK 1. Ignite the pilot light as described in the User Instructions 2.
Turn the appliance OFF and isolate the gas supply. Ensure the appliance is fully cold before attempting to start servicing the appliance. No liability can be accepted by Focus for injury caused by burning or scolding by a hot appliance.
Technical Information COUNTRIES OF USE Country Natural AT -Austria I2H, G20 at 20 mbar I3P(50),G31 at 50 mbar; I3B/P(50),G30/G31 at 50 mbar BE -Belgium I2E+, G20/G25 at 20/25 mbar I3+,G31/G31 at 28/37 mbar; I3P(37),G31 at 37 mbar; I3B/P(30),G30/G31 at 30 mbar BG -Bulgaria I2H, G20 at 20 mbar I3B/P(30),G30/G31 at 30 mbar...
Page 17
Technical Information TECHNICAL DATA Product Identification Number : 0359CQ0657 Curvifocus Natural Gas type Supply Pressure mbar 20/25 Nominal Heat Input Gross (Hs) 9 / 7.3 Nominal Heat Input Nett (Hi) 8.1 / 6.6 Consumption m³/hr 0.843 0.843/0.723 0.843/0.794 0.892 Burner Pressure (hot) mbar 14.2...
Appendix MERTIK FAULT FINDING CHART FUNCTION POSSIBLE CAUSE REMEDY Replace transmitter batteries. No Transmitter batteries low. 9V quality alkaline recommended. HANDSET START: Press both buttons Replace receiver batteries with 1.5V “AA” quality to start ignition (IGN) Receiver batteries low. alkaline batteries. sequence.
Page 20
Appendix FUNCTION POSSIBLE CAUSE REMEDY Check connection between cable & IGNelectrode. No Ignition components not operating properly. See wiring diagram, p. 23. Check IGN-electrode spark gap. See wiring diagram, p. 23. Check IGN-electrode. See wiring diagram, p. 23. Check IGN-cable for damage. See wiring diagram, p.
Page 21
Appendix FUNCTION POSSIBLE CAUSE REMEDY Check connection of cable to receiver and Pilot lit. No TC- and SW-cable reversed. interrupter. See figure 1. Magnet unit not operating properly. Replace gas valve or (magnet unit). Short between interrupter and SW-cable. Check connection to interrupter. No gas (magnet unit drops after 30 second Check gas supply.
Page 22
Appendix FUNCTION POSSIBLE CAUSE REMEDY Turn manual knob to “ON” position (positive latch Main burner is lit. No Manual knob in “MAN” position. is required). See “Manual Operation” p. 08. Too much draft at pilot (poor flame Main burner stays lit. No ...
3 Impasse Claque Patin F - 34380 Viols le Fort declares that the FOCUS independent gas fired convection heaters described here are in accordance with the appliances described in the EC-Type Examination Certificate No. UK-LHD-0359-0657R1 delivered by INTERTEK and comply with the essential requirements applicable to EN 613 :2001 + A1 :2008 and Regulation UE 2016/426.
Need help?
Do you have a question about the Curvifocus and is the answer not in the manual?
Questions and answers