Table of Contents
Related Manuals for Leadway LDW-TKV106
Summary of Contents for Leadway LDW-TKV106
- Page 1 GPS Vehicle tracker (LDW-TKV106) (GPS+GSM+SMS/GPRS) User Manual (1.4 Version) Please read this manual carefully before attempting installation and online activation. Pictures are for indication and illustration purposes only.
- Page 3 2. Features ●GSM 850/900/1800/1900 Quad band ●Wide for voltage input range: 9-36V DC ●GPS continuous positioning, GPRS timing interval ●Real-time tracking, history playback ●Check location information via SMS and GPRS (TCP) ●Tele-cutoff (petrol) function ●SOS alarm ●ACC ignition detection and Vibration alarm ●Low battery alert ●Over-speed alarm ●Voice monitor function...
-
Page 4: Red Led (Power/Working/Status)
Speed Accuracy 0.1m/s Time Accuracy Same as GPS Warm status Cold status Highest altitude 18000M Max speed 515 M/S ﹤4g Acceleration of Gravity 2.1.2 Others Temperature -20---65℃ Humidity 5%---95% Voltage 10V—25V Power 10V—25V ＜80MA Average Power Indicate the working condition and other conditions of GPS &... -
Page 5: Blue Led (Gps Status Indicator)
LED Status Meaning Continuously in bright state Working normally Continuously in dark state Low battery/power off 2.3 Green LED (GSM status indicator) LED Statue Meaning flashing Weak GSM signal/searching GSM signal Continuously in bright state GSM conversation/Start GPRS Continuously in dark state GSM not located 2.4 Blue LED (GPS status indicator) LED Status... -
Page 7: Method Of Installation
4. Method of installation 4.1. Preparation before installation 4.1.1 Open the packing box to check whether the type of device is correct and whether the accessories are included, or else please contact your distributor. 4.1.2Choose SIM card: each device needs to insert a GSM SIM card. Please refer to the distributor’s suggestions to choose the SIM card. -
Page 8: Installation
4.1.4 Installing SIM card: The SIM card slot is on the right side of device. Open the SIM card silicon seal, then insert the SIM card to the slot (do not insert the SIM card backwards).When the SIM card is ready you will hear a click. Or else please insert again and then replace the silicon seal. - Page 9 NOTE: 4.2.1 To prevent theft of the device, it should be installed as covertly as possible. Covertly installation is suggested. 4.2.2 Avoid placing the device close to higher power electrical devices, such as reversing radar, anti-theft device or other vehicle communication equipment; 4.2.3The device should be fixed into position with cable ties or wide double-side tape.
- Page 10 Line No. Specification Color Instruction Keypod Orange/Orange Connect to SOS button MIC-,MIC+ Black/Red Connect to Microphone Green Sending data(TX)backup White Receiving data (RX)backup Black Ground wire MOTOR Yellow Connect to relay control line Orange Connect to ACC ignition Black(thick) Vehicle12V/24V negative storage battery Red(thick) Vehicle12V/24V positive...
-
Page 12: Cautions Of Device Wiring
5. Cautions of device wiring 5.1 Power/ACC/Tele-cutoff (petrol/electricity) control line (4pin) 5.1.1 The standard voltage is 9V-36VDC.Please use the power Line which provided by the manufacturer. The red line is the positive. The black line is the negative. The negative should earth alone or link iron during installing. -
Page 13: Sms Command Format
6．SMS command format Note: All the setup below can be only made by Center number. Super User Setup Set the new center number and new password by SMS through mobile phone. If the setup is successful, the module will send a reply with ‘Config OK the Main User and Password Is Reset To 13689645010 (center no.): 123456 (new password)’. -
Page 14: Server Connection Setup
Note: The default APN of this product is CMNET. Server connection Setup Format: #803# domain name or IP address # port number# This command is used to set GPRS center server address, which could be fixed IP number. After the setup is successful, the module will send a reply with ‘config ok, the ip server is 59.188.20.67:8545’. - Page 15 Vibration Alarm Setup ） Format: #ZDBJ # sensitivity (1-15 # alarm mode (0,1 )# Sensitivity “1” is the most sensitive and of course “15” is the most insensitive. Alarm mode”0’ indicates vibration alarm is closed. Alarm mode”1” indicates the device will alarm you through calls or SMS. Note: SMS will be sent only when the device is online on the tracking system.
-
Page 16: Time Zone Setup
The value of state is “0” and “1”,”1” means “open over-speed alarm”, “0” means “close over-speed alarm”. Example: #CSBJ#80#0# After sending command successfully, the tracker will return a message “config OK The Warning Speed Is: 80 Off”. Time Zone Setup Format: #896# E or W # time zone # The value of state is “E”... -
Page 17: Remote Restart
numbers. (Only this number can do voice monitor.) ： For example You want to set four stored numbers #711# 000000#13567892314#13892341600#13625678900#13625678901# The new numbers will replace the old numbers, and it will send confirmation to the sender if the password is right….CONFG OK. - Page 18 7. SMS & Platform Tracking SMS location inquiry There is no need for Center number to add the password to inquiry. Other numbers need to add the password to inquiry. 1） Address tracking Format: #666#password# For example you send #666#000000# to the tracker, you will get a reply SMS as follow: SN: 886600000525 No.106, Sanlian Road, Longhua Town, Bao’an District, Shenzhen, China.
- Page 19 For details, please refer to our tracking system user manual. Notes 1. This non-waterproof equipment, please be sure to have waterproof bag. 2. This equipment has to work with GSM network. 3. Please ensure that there are enough expenses in SIM card in order to avoid the inconvenience of using.