Philips DVDR880/001 Service Manual page 57

The paths that are available for video routing and their description(Europe version):
Path ID Description
00 Input signal is VIDEO(CVBS) from digital board and will be re-routed back to the
digital board.
01 Input signal is from FRONT VIDEO(CVBS) IN and will be routed to the digital board.
02 No Routing.
03 Input signal is from FRONT S-VIDEO(Y/C) and will be routed to the digital board.
04 No Routing.
05 Input signal is CVBS from SCART1 and will be routed to the digital board.
06 Input signal is CVBS from SCART2 and will be routed to the digital board.
07 Input Signal is CVBS from Digital Board and it will be routed to Scart1 and Scart2.
08 Input signal is VIDEO(CVBS) from ANTENNA IN and will be routed to SCART2.
09 Input signal is VIDEO(CVBS) from SCART1 and will be routed to SCART2.
10 Input signal is VIDEO(CVBS) from SCART2 and will be routed to SCART1.
11 Signal path is routed Fast Blank from Scart2 pin16 and will be routed Scart1 pin16
12 Input Signal is YC from Digital Board and it will be routed to Scart1.
13 No Routing.
14 No Routing.
15 Input Signal is CVBS from TUNER and it will be routed to Digital .
16 No Routing.
17 Input Signal is routed from digital board YC to REAR S-VIDEO(YC) OUT
18 Signal path is routed from digital board RGB to RGB SCART1 and from digital board
CVBS to digital board CVBS.
19 No Routing.
20 Input RGB Signal is routed from Digital Board to SCART1(RGB),Input CVBS Signal
from Digital Board to Digital Board and Fast Blanking Signal from Scart 2 to Scart1.
21 Input Y/C Signal from Digital Board is routed to Rear Y/C Connector and Input Y/c
Signal from Front Y/C connector is routed to Digital Board.
The paths that are available for video routing and their description (Nafta region):
PATH ID DESCRIPTION
00 Input signal is VIDEO(CVBS) from digital board and will be re-routed back to the
digital board.A Cinch Cable need to be connected from Rear Cinch Out to Front
Cinch In for this Test.(Direct routing on analogue board from YUV In to YUV Out is
not Possible)
01 Input signal is from FRONT VIDEO(CVBS) IN and will be routed to the digital
board.This routing is same as the above path id.
02 Input signal is from REAR VIDEO(CVBS) IN and will be routed to the digital board.
03 Input signal is from FRONT S-VIDEO(Y/C) IN and the signal received will be routed
to the digital board.
04 Input signal is from REAR S-VIDEO(Y/C) IN and will be routed to the digital board.
05 No Routing.
06 No Routing.
07 No Routing.
08 Input signal is VIDEO(CVBS) from TUNER and will be routed to Y Pin of Rear Y/C
Connector.This will give only black/White Picture .
09 Input signal is from YUV IN and will be routed to YUV OUT.This is possible only if
Digital Board routes back YUV signal received back to the Analogue board(DENC)
10 No Routing.
11 No Routing.
12 No Routing.
13 No Routing.
14 No Routing
15 Input CVBS Signal from Tuner is routed to Digital Board..
16 No Routing
17 Input RGB Signal is routed from Digital Board to RGB Rear Out and Input CVBS
Signal is routed from Rear Cinch In 1 to Digital Board(This second step is for routing
Input CVBS Signal from Digital Board to Digital Board again - A Cinch cable need
to be connected from Rear Cinch Out1 to Rear Cinch In 1 )
18 Input Signal from CVBS Rear In is routed to Digital Board.This is same as path id 02.
19 Input Y/C signal from Digital Board is routed to Y/C Rear Out Connector and Input
signal from Y/C Rear In Connector is routed to Y/C Digital Board.
Diagnostic Software DVDR880-890 /0X1 5. EN 59