1. Manuals
  2. Brands
  3. Philips Manuals
  4. Home Theater System
  5. HTS5506/F7
  6. Service manual

Philips HTS5506/F7 Service Manual

Blu-ray disc home theater
Hide thumbs Also See for HTS5506/F7:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
SERVICE MANUAL
BLU-RAY DISC HOME THEATER
HTS5506/F7

Advertisement

Table of Contents
loading

Related Manuals for Philips HTS5506/F7

Summary of Contents for Philips HTS5506/F7

  • Page 1 SERVICE MANUAL BLU-RAY DISC HOME THEATER HTS5506/F7...

  • Page 2: Table Of Contents

    IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

  • Page 3: Specifications

    SPECIFICATIONS General Signal system NTSC Color Power requirements 120 V AC, 60 Hz Power consumption 70 W (standby: 0.6 W) Total output power (Amplifier) Home theater mode: 1000 W FTC* output power: 700 W * (Main Ch @ 1 kHz within 10 % THD, Sub Ch 60 Hz within 2.5 % THD) Dimensions (width x height x depth) 17.2 x 2.4 x 11.1 inches (435 x 60 x 281 mm) Weight...

  • Page 4: Laser Beam Safety Precautions

    LASER BEAM SAFETY PRECAUTIONS This BD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 11.8 inches (30 cm) away from the pickup lens when the diode is turned on.

  • Page 5: Important Safety Precautions

    IMPORTANT SAFETY PRECAUTIONS Product Safety Notice H. When a power cord has been replaced, check that 11~13 lb (5~6 kg) of force in any direction will not Some electrical and mechanical parts have special loosen it. safety-related characteristics which are often not Also check areas surrounding repaired locations.
  • Page 6 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards. 1.

  • Page 7: Standard Notes For Servicing

    STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is When soldering, be sure to use the Pb free solder. indicated as shown. How to Remove / Install Flat Pack-IC Top View Bottom View 1.
  • Page 8 3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
  • Page 9 2. Installation With Iron Wire: 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
  • Page 10 Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.

  • Page 11: Cabinet Disassembly Instructions

    CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Fig. Loc. Part Removal Note This flowchart indicates the disassembly steps to gain access to items to be serviced. When reassembling, AMP/PSU (S-14), 5(S-15), follow the steps in reverse order. Bend, route, and [11] PCB Bracket Front dress the cables as they were originally.
  • Page 12 (S-1) (S-1) [5] T-Sensor CBA [4] Front CBA CN2501 Touch PCB Holder Assembly Guard Panel (S-2) (S-3) (S-2) [1] Top Cover (S-1) [6] Front Assembly Volume Knob Assembly Fig. D3 [7] *BD Main CBA Fig. D1 CN7002 CN7003 [8] *BD Mechanism CN3503 Assembly (S-6)
  • Page 13 [9] *Rear Panel (S-8) (S-9) (S-10) (S-11) (S-12) Motor DC Fan CN5001 * See Reference Note 4. Fig. D5 [10] Jack CBA (S-13) (S-14) (S-15) (S-15) PCB Bracket Front (S-15) (S-16) [11] AMP/PSU [12] USB CBA Fig. D6 1-5-3 E1U21DC...
  • Page 14 3. How to Eject a Disc When a disc cannot be removed due to malfunction or when an unplayable disc is inserted, follow the procedure below to remove the disc. Procedure A 1. Unplug the AC power cord and then plug it in. 2.

  • Page 15: How To Initialize The Blu-Ray Disc Home Theater

    HOW TO INITIALIZE THE BLU-RAY DISC HOME THEATER To put the program back at the factory-default, initialize the BD player as the following procedure. Note: • By initializing, network is reset to disconnected state and “Network Service Disclaimer” appears on the screen.

  • Page 16: Firmware Renewal Mode

    FIRMWARE RENEWAL MODE Note: The file extension of the available firmware is The appearance shown in (*1) of Fig. b is “b40”. described as follows: 1. Turn the power on and remove the disc on the tray Appearance State and close the tray. 2.
  • Page 17 How to Verify the Firmware Version 1. Turn the power on. 2. Remove the disc on the tray and close the tray. 3. Press [ ] (skip up), [1], [2], and [3] buttons on the remote control unit in that order. Fig.
  • Page 18 FIRMWARE RENEWAL MODE (for User) Disc/USB Memory Stick/SD Card Update 1. Press [ ] button to display Setup menu. 7. Firmware loading starts. Fig. l will appear on the screen and Fig. m will appear on the VFD. 2. Select Setup - Advanced Setup - Software Update. 3.

  • Page 19: Network Update

    Network Update 1. Press [ ] button to display Setup menu. 7. The unit starts reading the firmware. Fig. s will appear on the screen and Fig. t will appear on the 2. Select Setup - Advanced Setup - Software Update VFD.
  • Page 20 Network Error Message Error Message The cable is not connected. Please confirm the connection of the cable. DHCP cannot be acquired. Please confirm connection or set it with the manual operation. Internet Protocol address is not set. Please confirm the set content. The equipment with same Internet Protocol address already exists.

  • Page 21: Adjustment Instructions For Bd Main Cba Or Bd Mechanism Assembly Replacement

    ADJUSTMENT INSTRUCTIONS FOR BD MAIN CBA OR BD MECHANISM ASSEMBLY REPLACEMENT When replacing either BD Main CBA or BD Mechanism Assembly, the unique OPU DATA of the BD Mechanism needs to be written into the BD Main CBA. Follow the procedure below for OPU DATA write operation. Equipments: •...
  • Page 22 Caution: • Make sure the FFC cable is inserted in the proper direction so the Pin 1 of COMTOOL jig relay board and Pin 1 of BD MAIN CBA connector is connected. Location of Pin 1 on BD Main CBA Pin 1 is located on the bottom side 1pin •...
  • Page 23 4. OPU DATA WRITE 4-1. Connect the unit’s AC power cord. Wait for about 30 seconds until the unit is in standby mode. 4-2. Double click on the [OpuDataWriter.exe] shortcut on the desktop to start the application. 4-3. Application start screen appears. Select the assigned connection port of [USB Serial Port] for the [COM PORT] field located at the right corner of the screen.
  • Page 24 4-6. Data write begins. While writing data, the Status Display message will change. Status Display SEND LD PAR 4-7. [OK] appears in the Status Display if data write has been completed successfully. If error occurs: • If an error occurs, the screen changes to a red display. In such case, close the window and then unplug the unit AC power cord.
  • Page 25 Error Code Error Code Error Description Start word error The first letter entered for [LOADER S/N] does not match. [ReadBackup]Drive Mount error Cannot mount the drive set for [ReadBackup] folder. [Transfer]Drive Mount error Cannot mount the drive set for [Transfer] folder. [OpuData]Drive Mount error Cannot mount the drive set for [OpuData] folder.
  • Page 26 Error Code Error Description 2042 LdParamClear ERROR0 Cannot initialize LD Parameter. 2043 LdParamClear ERROR1 Cannot initialize LD Parameter. 2044 LdParamClear TIME OUT Cannot initialize LD Parameter (TimeOut). 2051 IopSet NG Iop Set Error 2052 IopSet ERROR0 Iop Set Error 2053 IopSet ERROR1 Iop Set Error 2054...

  • Page 27: Troubleshooting

    TROUBLESHOOTING FLOW CHART NO.1 The power cannot be turned on. See FLOW CHART No.2 <The fuse blows out.> Is the fuse normal? Is normal state restored when once unplugged Check for lead or short-circuiting of primary power cord is plugged again after several seconds. circuit component and replace AMP/PSU CBA if defective.
  • Page 28 FLOW CHART NO.4 Audio does not appear normally. Set the disc on the disc tray, and playback. Are the audio signals(serial data) outputted to Replace BD Main CBA or BD MECHANISM Pin(3, 4, 5, 6) of CN201? ASSEMBLY. Replace AMP/PSU CBA. 1-9-2 E1U00TR...

  • Page 29: Error Message

    ERROR MESSAGE Note: Only error messages for the unit’s corresponding media will appear. Disc Error - - Please eject the disc. - - Playback feature may not be available on this Disc. Error Message Disc Error Disc Error - - Please eject the disc. - - Playback feature may not be available on this Disc.
  • Page 30 Error Message It is not possible to connect to the server. Cannot Connect To Server Please contact our support center. It is not possible to confirm the software version. Cannot Confirm Firmware Version Please contact our support center. Error detected. File may be corrupted.

  • Page 31: Home Network (Dlna) Error Code

    HOME NETWORK (DLNA) ERROR CODE Error Code appears in the error screen when the unit “Summary Error Code” are shown in the list below. detects an error, as shown below. The code is used to Summary specifically determine the cause of error. Error message Error Code Network Error...
  • Page 32 Detailed Error Code table (DLNA – HTTP Status Code) Status Code Description 201 Created A new resource was created by this unit’s request. 202 Accepted This unit’s request was accepted but its processing is not completed. 204 No Content Though the server processed the request, there was no content. 205 Reset Content No content.
  • Page 33 Status Code Description • Proxy authentication is required. 407 Proxy Authentication • Indicates that the requested proxy will request authentication. Proxy-authenti- Required cate header contains the detailed method for authentication. • While waiting for request, the server timed out. 408 Request Timeout •...
  • Page 34 Detailed Error Code table (DLNA – Application Status Code) Status Code Description As a result of list creation process, there is no item to be displayed from the 001 Nothing List received data. 010 LAN Disconnect This unit’s LAN is disconnected. 020 Application Status Error Error was detected in the DLNA application’s internal state.
  • Page 35 Status Code Description 664 1sec Offset Get Error 1sec offset get error. 665 Address Search Error Address search error. 680 RFS_EVENT_SOCKET_ Socket error. ERROR 681 RFS_EVENT_HTTP_ RES_SERVER_ Server refusal notification. REFUSED 682 RFS_EVENT_HTTP_ The specified contents could not be found. RES_NOT_FOUND 683 RFS_EVENT_HTTP_ Server error.
  • Page 36 Status Code Description 710 Object Count Zero Nothing was found in the folder. 711 ILLEGAL Server Info The contents information from the server is invalid. 712 ILLEGAL Total Count The total counts of contents from the server is invalid. The specified folder does not exist. (The current contents list displayed has 713 Folder not Exist been updated) 714 Critical Error...
  • Page 37 MediaConnect NETWORK ERROR When the unit detects a MediaConnect Network Error, the error screen is displayed as shown below. Network Error Cannot connect to Network/Computer. NE [00302010] Error message Error Code Fig. 3 Description of Error Message Error Message Description Invalid LAN (Wired/Wireless).

  • Page 38: Block Diagram

    BLOCK DIAGRAM OVERALL BLOCK Diagram (TO FAN) (TO AC CORD) JK201 16pin JK402A JK402 JK401A Speaker OUT X 6ch CN5001 2pin CN9000 2pin AUX2 WIRELESS JACK AUX1 AMP Block PSU Block Fuse TU401 AMP/PSU CBA FM Tuner AMP Power IC301 Over Detect Multi Plexer Filter...

  • Page 39: Schematic Diagrams And Cba

    SCHEMATIC DIAGRAMS AND CBA Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
  • Page 40 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED.
  • Page 41 AMP/PSU 1 Schematic Diagram CJS012201-0010 34V_4 34V_3 34V_2 34V_1 34V_4 34V_2 JK401A R5014 C5099 C5101 R5016 R5017 C5102 C5103 R5018 R5019 C5104 C5106 R5021 R5022 C5107 C5108 R5023 R5024 C5109 C5111 R5026 R5027 C5112 C5113 R5028 JK5001 C5075 C5076 C5077 C5078 C5079 C5080...
  • Page 42 AMP/PSU 2 Schematic Diagram CAUTION ! For continued protection against fire hazard, CAUTION ! replace only with the same type fuse. NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. ATTENTION : Pour une protection continue les risqes The voltage for parts in hot circuit is measured using If Main Fuse (F9000) is blown , check to see that all components in the power supply d'Incele n'utiliser que des fusible de même type.
  • Page 43 Jack Schematic Diagram 0R(open) R474 +BIAS R416 C470 C480 R455 C445 0.1UF 100UF/25V +BIAS IC404A JRC4558 C443 4.7U R453 RCA_4CH_H C462 R462 AUX-L R459 R427 R541 AUX1R_IN 4.7UF16V C493 C425 4.7UF16V AUX1L_IN C447 47P C491 JK402 100P R428 AUX1L_IN R440 R457 IN+12V A+12V...
  • Page 44 Front Schematic Diagram IC2001 MATRIX CHART TO BD MAIN CN2502 CBA CN6404 FRONT CBA IC2001 8-NY-03NK (VFD) 1 GND 2 GND 3 +5V 4 DN 5 DP WIRELESSBD CN2503 LAN MODULE 1 DP 2 DN 31 32 3 +5V R2005 R2028 R2026 4 GND...
  • Page 45 T-Sensor Schematic Diagram USB Schematic Diagram R4001 R4002 C4003 C4002 100P 100P TO BD MAIN CN2801 R2801 CBA CN6405 CN2802 (USB JACK) 1 +5V 2 DN 3 DP R2802 0 4 GND R2803 0 IC4001 5701-UG320WT (TOUCH SENSOR) C4001 USB CBA TO FRONT CN4001 CBA CN2501...
  • Page 46 BD Main 1 Schematic Diagram CN6101 (TO AMP/PSU CBA UNIT CN9001) (TO BD MAIN 9) SAFETY C6107 R6114 C6112 IC6107 TP101 TP103 EV+12V BD9329EFJ-E2 560P 0.1[F] C6158 0.1[F] R6113 D6116 D6102 1SS400 EV+12V R6118 C6157 A8V_REG P_S[2125] 1SS400 C6101 C6161 C6106 C6170 COMP...
  • Page 47 BD Main 2 Schematic Diagram C0DQ[0-31],C0DS[0-3],C0XDS[0-3],C0DM[0-3],C0A[0-13],C0BA[0-2],C0CK,C0XCK,C0CKE,C0XCS[0,1],C0XWE,C0XCAS,C0XRAS,C0ODT,C0XRESET IC6001 C0DQ0 C0DQ0 C0DQ1 C0DQ1 IC6201 IC6202 C0DQ2 C0DQ2 K4B1G1646E-HCH9 K4B1G1646E-HCH9 IC6203 C0DQ3 C0DQ3 H5TQ1G63DFR-H9C H5TQ1G63DFR-H9C K4B2G1646C-HCH9 C0DQ4 C0DQ4 H5TQ1G63BFR_H9C H5TQ1G63BFR_H9C H5TQ2G63BFR_H9C C0DQ5 C0DQ5 NT5CB64M16AP-CG NT5CB64M16AP-CG NT5CB128M16BP-CG C0DQ6 PON+1V5 PON+1V5 PON+1V5 C0DQ6 C0DQ7 C0DQ7 C0DQ8 C0A0 C0A0...
  • Page 48 BD Main 3 Schematic Diagram EA[0-7,24],ED[0-15] PON+3V3 PON+3V3 PON+3V3 CN6303 PON+3V3 FLASH 04 6274 050 000 800+ BC6303 SHORT[1608] IC6001 IC6307 K9F2G08U0C-PCB0 HY27UF082G2B-TPCB NANDRYBY DGND AG24 NANDRYBY AH23 NAND02GW3B2DN6E NFALE AF24 NFALE AG23 NFCLE AK25 NFCLE AF23 XNFCE AJ25 XNFCE AE23 XNFRE AH25...
  • Page 49 BD Main 4 Schematic Diagram PON+3V3 HDMI VIDEO L6401 DLP2ADN900HL4L IC6001 IC6001 IC6001 D2GND (TO BD MAIN 8) L6601 R6633 R6438 HTTX2P D1GND AO2DACCK AO2DACCK VO1CLK R6634 SHORT HTTX2M AO2BCK AO2BCK PON+3V3 R6635 AO2LRCK AO2LRCK HTTX1P D0GND AO2DMIX R6601 HTTX1M AO2D0 AO2D0 L6402...
  • Page 50 BD Main 5 Schematic Diagram PON+3V3 IC6001 CK25O CK25O PON+3V3 L6501 MII_TXCLK R6526 SHORT MII_TXCLK P_S[1608] MII_TXD0 MII_TXD0 MII_TXD1 MII_TXD1 MII_TXD2 MII_TXD2 MII_TXD3 MII_TXD3 MII_TXEN MII_TXEN MII_RXCLK MII_RXCLK MII_RXD0 MII_RXD0 MII_RXD1 MII_RXD1 MII_RXD2 MII_RXD2 MII_RXD3 PON+3V3 MII_RXD3 VDDIO MII_RXDV MII_RXDV MII_RXER MII_RXDV R6511...
  • Page 51 BD Main 6 Schematic Diagram IC6001 PON+1V5 PON+1V1 VDDIO C6704 0.1[F] C6729 0.1[F] VDDIO C6705 0.1[F] C6730 0.1[F] W11 VDDIO C6706 0.1[F] C6731 0.1[F] W12 VDDIO IC6001 C6707 0.1[F] C6732 0.1[F] VDDIO IC6001 C6708 0.1[F] C6733 0.1[F] VDDIO C6709 0.1[F] C6734 0.1[F] VDDIO...
  • Page 52 BD Main 7 Schematic Diagram TP170 VHALF CN7004 CN7005 CN7006 CN7007 VREFH PON+3V3 BM10B-SRSS-TB 6266-010 6266-010 04-6232-106-102-800+ AVCC PON+3V3 TP174 R7080 TP210 THERMOOP THERMO R7138 VC_PD R7139 (TO BD MECHANISM IC7003 PON+3V3 LM324PWR ASSEMBLY) R7140 DGND DGND CN7003 R7141 (TO BD MAIN 3) XFERST R7161 DGND...
  • Page 53 BD Main 8 Schematic Diagram R3035 R3036 R3037 R3038 PON+3V3 PON+3V3 IC3001 PON+3V3 IC3101 PON+3V3 L3001 TAS3108 L3101 TAS3108 X3101 X3001 0[1608] L3002 P_S[1608] L3102 12.288MHz 12.288MHz 3.3[1608] 3.3[1608] 1 AVSS AVDD AVSS AVDD C3005 0.1[B] C3105 0.1[B] VR_PLL RESERVED_2 VR_PLL RESERVED_2 R3017...
  • Page 54 BD Main 9 Schematic Diagram EV+3V3 PON+3V3 PON+5V R5048 CEC-IN D5001 1SS355 FROM BP2(P4) SUB_B_Rx R5045 SHORT DSEL_A SUB_B_Tx PON+3V3 HDMI B_RST Q5002 TP384 KTC3875S-Y-RTK/P (TO BD MAIN 4) L3604 R5025 R3603 CEC-OUT C5017 330P[CH] P_S[1608] IC3601 DGND (TO BD MAIN 4) L3606 SN74LVC1G3157DCKR 100K...
  • Page 55 AMP/PSU CBA Top View CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F9000) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
  • Page 56 AMP/PSU CBA Bottom View CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F9000) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
  • Page 57 Jack CBA Top View 1-13-19...
  • Page 58 Jack CBA Bottom View 1-13-20...
  • Page 59 Front CBA Top View CN2503 BE1U21F0101 D2501 J2503 Ver.3 RS2001 IC2001 C2007 J2504 DGND J2502 REMOTE J2505 VFD+5V CN2502 VR2001 CN2005 Front CBA Bottom View 1-13-21...
  • Page 60 USB CBA Top View USB CBA Bottom View R2801 CN2802 BE1U21F0101 CN2802 BE1U21F0101 Ver.3 R2802 R2803 T-Sensor CBA Top View T-Sensor CBA Bottom View POWER STOP SOURCE PLAY BE1U21G0201 IC4001 OP/CL Ver.3 D4001 1-13-22...
  • Page 61 BD Main CBA Top View R6473 C3003 R3016 C3005 C3104 C3103 R3139 C3105 R6318 R6317 R6566 C3004 R7131 TP289 R6319 R6320 Q3002 R6114 C6107 R6113 X3001 X3101 Q3001 TP291 R6328 TP294 R6330 R7133 TP290 R6625 R6624 R6626 R6627 R6622 R6623 TP293 R6617 BC6702...
  • Page 62 BD Main CBA Bottom View JK3006 (VIDEO OUT) 1-13-24...

  • Page 63: Waveform

    WAVEFORM JK3600 (VIDEO OUT) CVBS CVBS 0.5V 0.5V 20µsec NOTE: Input: COLOR BAR SIGNAL (WITH 1KHz AUDIO SIGNAL) 1-14-1 HT4N2WF...

  • Page 64: Wiring Diagram

    WIRING DIAGRAM EXPB(+) EXPB(-) EXPA(+) EXPA(-) THERMO BD-LD TEST-V SPEAKER TERMINAL LD-TYPE CD-LD AVCC PD-LD LDON SDIO DVD-LD SCLK DSEN AVCC FPIO1 RF(-) RF(+) VC-PD VFD+5V VFD-STB LOAD(-) LOAD(+) VFD-DAT TRAY-IN VFD-CLK REMOTE EV+3V3 I2C-SCL VH(+) I2C-SDA HU(+) HU(-) HV(+) VOLUME-UP HV(-) VOLUME-DOWN...

  • Page 65: Exploded Views

    EXPLODED VIEWS Cabinet 2L001 2L001 2L040 2L020 BD Main CBA 2L021 Jack CBA 2L001 2L010 2L022 2L022 2L006 2L008 2L005 2L002 2L007 2L022 2L022 AMP/PSU CBA 2L003 2L025 T-Sensor CBA Motor DC Fan 2L030 2L011 2L030 2L011 See Electrical Parts List USB CBA for parts with this mark.
  • Page 66 Packing Upper Side Lower Side S1-A S1-B Some Ref. Numbers are not in sequence. 1-16-2 E1U21PEX...

  • Page 67: Mechanical Parts List

    USPSPKHYE005 through improper servicing. X20# OWNERS MANUAL E1U21UD 1VMN30773 QUICK GUIDE E1U21UD 1VMN30774 NOTE: Parts that are not assigned part numbers BROCHURE (PHILIPS) A01N2UH 1EMN26419 (---------) are not available. VUDU SHEET E5S20UD 1VMN30133 NETFLIX GUIDE E5PG0UD 1VMN28453A Ref. No. Description Part No.

  • Page 68: Electrical Parts List

    ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C2018 CHIP CERAMIC CAP .(1608) B K 1000pF/50V CHD1JK30B102 Before replacing any of these components, read CONNECTORS carefully the product safety notice in this service CN2005 FFC CONNECTOR 22P IMSA-9615S-22C-PP-A JC96J22ER009 manual.
  • Page 69 T-SENSOR CBA Ref. No. Description Part No. T-SENSOR CBA 1VSA27173 Consists of the following: CAPACITORS C2901 CHIP CERAMIC CAP .(1608) F Z 0.1µF/25V CHD1EZ30F104 C2902 CHIP CERAMIC CAP .(1608) CH J 100pF/50V CHD1JJ3CH101 C2903 CHIP CERAMIC CAP .(1608) CH J 100pF/50V CHD1JJ3CH101 CONNECTOR CN2901...
  • Page 70 Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law. HTS5506/F7 E1U21UD 2011-05-30...

Table of Contents