Yamaha RS7000 Service Manual page 48

RS7000
[LOOP REMIX], [SAMP EDIT], [STANDBY], [SELECT],
[WAVE], [<AMP/FILTER/PITCH>], [PORTAMENTO TYPE],
[TYPE], [F1], [F2], [F3], [F4], [SHIFT], [REC], [<], [STOP],
[PLAY], [<<], [>>], [KEYBOARD], [ARPEGGIO ON], [OCT
DOWN], [OCT UP], [STORE], [SCENE], [<MEMORY>1],
[ < M E M O RY > 2 ] , [ < M E M O RY > 3 ] , [ < M E M O RY > 4 ] ,
[<MEMORY>5], [EXIT], [PATTERN], [PATT CHAIN], [SONG],
[UTILITY], [GROOVE], [PLAY FX], [MIDI DELAY], [MIXER],
[VOICE EDIT], [EFFECT], [SETUP], [MASTER], [SAVE],
[LOAD], [JOB], [EDIT], [TRANSPOSE], [A], [B], [C], [D], [E],
[F], [G], [H], [I], [J], [TAP], [MUTE], [TRACK SELECT], [1], [2],
[3], [4], [5], [6], [7], [8], [9], [10], [11], [12], [13], [14], [15], [16]
If the test result is satisfactory, a sine wave will be output while
the switch is on, and you will proceed to the test for the next
switch.
If a code is transmitted for a switch other than the one displayed
in the LCD, the display will indicate NG, and no sound will be
output. If the correct code is subsequently received, you will
proceed to the test for the next switch.
If all switches are satisfactory, the LCD will indicate OK. The
test will end, and you will be able to select a different test item.
If a result of NG is returned during this test, refer to section "(E)
Proceeding to the next test if a result is NG" for the actions to
take.
(Test result display)
//// RS7000 Test Program ////
OK
04:Panel SW
NG
//// RS7000 Test Program ////
04:Panel SW :Press [xxxxxxx] NG
5. Encoders 1-4
//// RS7000 Test Program ////
05:Encoder
This test verifies that the encoders operate correctly.
48
:OK
[-1] [+1]
:Press [ENTER]
[-1] [+1]
(Test method)
As directed by the following LCD screen, turn each encoder
clockwise (value: +0 -> +8), and then counter-clockwise (value:
-0 -> -8).
//// RS7000 Test Program ////
05:Encoder
Encoder-1
Encoder-2
Encoder-3
Encoder-4
Verify that the number at the right of the screen increases
smoothly from +0 to +8 when the encoder is turned clockwise,
and decreases smoothly from -0 to -8 when the encoder is turned
counter-clockwise.
If the operation is normal, a result of OK will be displayed in the
LCD. The test will end, and you will be able to select a different
test item.
If a result of NG is returned during this test, refer to section "(E)
Proceeding to the next test if a result is NG" for the actions to
take.
(Test result display)
//// RS7000 Test Program ////
OK
05:Encoder
Encoder-1
Encoder-2
Encoder-3
Encoder-4
NG No display
6. Knobs 1-22
//// RS7000 Test Program ////
06:Knob
This checks whether the knobs operate correctly.
(Test method)
As directed by the following LCD screen, smoothly move each
knob from right -- left (value: 127 (126-127) -- 0 (0-1)).
yy: target value
:<yy> xx
xx: current value
:<yy> xx
:<yy> xx
:<yy> xx
: OK
: OK
: OK
: OK
:Press [ENTER]
[-1] [+1]