Page 1
IMPORTANT! Please keep these instructions for future reference. Please read these instructions before assembly and use of this product. • Adult assembly is required. Allen wrench (included) required for assembly • Phillips Head Screw Driver (Not Included) required for assembly. •...
Part Lists A.Top Panel x1 C.Right Panel x1 D.Tray Back Rail x1 B.Left Panel x1 E.Tray Front Rail x1 F.Tray Side Rail x2 G.Back Top Rail x1 H.Front Top Rail x1 J.Front Middle Rail x1 K.Dust Panel x1 I.Back Middle Rail x1 L1.
Page 3
Part Lists 2”Allen head Bolt X 8 1-1/8”Allen head Bolt X 22 Drawer Knob X 2 1”Knob Bolts X 2 Plastic Crescent Washer X 8 Cam Rods X 4 5/8”Wood Screw Cam Lock X 4 (for Back Panel) X26 1”Wood Screw X11 Anti-Tip Kit x1bag (Instruction and Hardware inside) plastic bag...
Assembly step 1 Plastic Crescent G.Back Top Rail x1 Washer X 4 M.Back Bottom Rail x 1 C.Right Panel x1 2”Allen head Bolt X 4 H.Front Top Rail x1 A4 Allen WrenchX 1 Wood Dowel X 2 Figure 1 Figure 2 Note: During Assembly, Left Panel (B) and Right Panel (C) will mirror each other.
Page 7
Assembly step 2 I.Back Middle Rail x1 L1.Top Shelf x 1 L2.Bottom Shelf x 1 1-1/8”Allen head Bolt X 4 Wood Dowel X 1 J.Front Middle Rail x1 Figure 1 Figure 2...
Page 10
Assembly step 5 2”Allen head Bolt X 4 Y Plastic Crescent A4 Allen WrenchX 1 Washer X 4 B.Left Panel x1 1-1/8”Allen head Bolt X 4 Wood Dowel X 3 Figure 1 Figure 2 Figure 4 Figure 3...
Page 11
Assembly step 6 Wood Dowel X 8 Cam Lock X 4 D.Tray Back Rail x1 F.Tray Side Rail x2 Cam Rods X 4 E.Tray Front Rail x1 Note:If the screwdriver is too long, you can use Allen Wrench (A5).
Page 12
Assembly step 7 1-1/8”Allen head Bolt X 6 A.Top Panel x1...
Page 13
Assembly step 8 1-1/8”Allen head Bolt X 8 A4 Allen WrenchX 1...
Page 14
Assembly step 9 5/8”Wood Screw (for Back Panel) X26 Tracking Label T1.Top Back Panel x 1 T2.Bottom Back Panel x 1 Tracking Label Figure 1...
Page 15
Assembly step 10 1”Knob Bolts X 2 1”Wood Screw X 9 Drawer Knob X 2 Q.Drawer Back x 1 N.Drawer Front x 1 O.Drawer Left x 1 Wood Dowel X 2 R.Drawer Bottom x 1 S.Drawer Support x 1 P.Drawer Right x 1 Note: Grooves on Drawer Sides and Drawer Back should all face inward to allow Drawer Bottom to be inserted.
Page 16
Assembly step 11 Anti-Tip Kit x1bag (Instruction and Hardware inside) plastic bag Drawer x 1 plastic Note: Please follow instructions in Anti-Tip Kit when assembly is complete.
Page 17
CHANGING STATION Read all instructions before use of changing station. KEEP INSTRUCTIONS FOR FUTURE USE. This Changing Station is intended for use with children weighing up to 30 pounds. This Changing Station may be used with or without a pad. If using a Contour Pad, the maximum thickness should NOT exceed 4 inches (100 mm).