Tork EWZ201 Instruction Manual
  1. Manuals
  2. Brands
  3. Tork Manuals
  4. Switch
  5. EWZ201
  6. Instruction manual

Tork EWZ201 Instruction Manual

Digital time switch
Hide thumbs
Table of Contents

Advertisement

Quick Links

MLI-212(B)

Advertisement

Table of Contents
loading

Related Manuals for Tork EWZ201

Summary of Contents for Tork EWZ201

  • Page 1 MLI-212(B)

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Installation Instructions and Capabilities ....Set Clock ..... . . To Modify Clock (After previously Set) .

  • Page 3: Capabilities

    TORK MODEL EWZ201 2 CHANNEL 7 DAY DIGITAL TIME SWITCH READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL TIME SWITCH. SEE WARNING ON FRONT PANEL – Failure to comply with instructions could result in personal injury and/or proper- ty damage. INSTALLATION: UNIT IS TO BE INSTALLED BY A LICENSED ELECTRICIAN 1.

  • Page 4: Set Clock

    PROGRAMMING YOUR EWZ 201 NOTE: AFTER MAKING ANY CHANGES TO THE PROGRAM, PRESS MODE TO GO TO RUN MODE AND THEN PRESS EVENT TO UPDATE THE LOAD STATUS. AT POWER UP: Unit should be program with AC power. Do not pro- gram under super cap back up power.

  • Page 5: To Modify Date (After Previously Set)

    Press MONTH, DATE, and YEAR key to advance to the desired Month, Date and Year, then press ENTER. NOTE: The day of the week will be automatically set once the date is set. 2.1 TO MODIFY DATE Press MODE until the display shows DATE. Press MONTH, DATE and YEAR to modify present set- tings and then press ENTER.

  • Page 6: To Modify Daylight Saving Time

    TO MODIFY STANDARD USA DAYLIGHT SAVINGS DATES MO TU WE TH F R SA AST RO Press MONTH and DATE, to modify S (starting) DST settings. NOTE: DATE will choose the week of the month to be assigned. Choices are 01 (1st), 02 (2nd), 03 (3rd) or L (Last) week of the month.

  • Page 7: Setting Hour, Minutes And Days

    4.1 SETTING HOURS, MINUTES AND DAYS a. Press HOUR and MIN to set desired time. b. Press EVENT to set desired event (ON/OFF). Press DAY to select desired days and then press ENTER. The display will show: CLK DATE AUTO MAN Follow the same procedures above to set more schedule entries for channel 1.

  • Page 8: Astronomic On And Time Off

    If an offset to sunset time is required, press HOUR and MIN. Offset can be set to 4 hours and 59 min- utes max. Press EVENT to select + or – and then press ENTER. NOTE: A + sign will turn load ON that many hours and/or minutes after sunset.

  • Page 9: Time On And Astronomic Off

    6.1 TIME ON AND ASTRONOMIC OFF Press MODE until “sch01” appears. Press ENTER until a blank schedule appears then press CH1/CH2 to select channel 1 or 2. Press HOUR, MIN and EVENT to set desired ON time. Press DAY to select desired days and then press ENTER.

  • Page 10: Review, Modify, Delete Schedule

    7.0 REVIEW, MODIFY AND DELETE Press MODE to advance to any of the following MODES: 1. CLOCK MODE: Press HOUR and MIN to modify existing settings. Press ENTER. 2. DATE MODE: Press MONTH, DATE and YEAR to modify existing settings. Press ENTER. DAY is automatically adjusted.

  • Page 11: Use As Momentary Unit

    10.0 USE AS MOMENTARY UNIT This unit can also be field converted to be used as momentary unit. To make this conversion, remove jumper in back of the unit. Reset the unit by insert- ing a small pin or paper clip into the small hole next to the EVENT key and re-setting the clock and date.
  • Page 12 NOTE: Unit has permanent memory and will not be erased unless done through procedure above. 5. Upon powering up your EWZ201 the display will show at what frequency the unit is operat- ing, 50 will determine 50Hz or 60 for 60Hz.
  • Page 16 888.500.4598 • www.nsiindustries.com...

Table of Contents