Individual Parameters; System Parameters - Roland HP-337 Manual

3. Parameter Address Map (Model ID = 42H)
This map indicates address, size, Data (range), Parameter, Description, and Default Value of parameters which can be transferred using and "Data set 1 (DT1)."
All the numbers of address, size, Data, and Default Value are indicated in 7-bit Hexadecimal-form.
Address Block map
An outlined address map of the Exclusive Communication is as follows;
Address (H) Block
40 00 00 +————————————————————————————————————+

| SYSTEM PARAMETERS

40 01 3F +————————————————————————————————————+
40 1x 00 +————————————————————————————————————+
| PART PARAMETERS
| (x = 0-F)
40 2x 5A +————————————————————————————————————+
41 m0 00 +————————————————————————————————————+
| SRUM SETUP PARAMETERS
| (m = 0-1)
41 m8 7F +————————————————————————————————————+
48 00 00 +————————————————————————————————————+
| SYSTEM PARAMETERS
48 01 10 +————————————————————————————————————+
| PART PARAMETERS
48 1D 0F +————————————————————————————————————+
49 m0 00 +————————————————————————————————————+
| DRUM SETUP PARAMETER
| (m = 0-1)
49 mE 17 +————————————————————————————————————+
There are two ways in which GS data is transmitted: Individual Parameter Transmission in which individual parameters are transmitted one by one, and Bulk Dump Transmission in which a
large amount of data is transmitted at once.

Individual Parameters

Individual Parameter Transmission transmits data (or requests data) for one parameter as one exclusive message (one packet of "F0 ..... F7").
In Individual Parameter Transmission, you must use the Address and Size listed in the following "Parameter Address Map." Addresses marked at "#" cannot be used as starting addresses.
System Parameters
Parameters related to the system of the device are called System Parameters.
Address (H) Size (H)
40 00 00 00 00 04
40 00 01#
40 00 02#
40 00 03#
* Refer to section 4. Supplementary material, "About tuning" (p. 14).
40 00 04 00 00 01
40 00 05 00 00 01
40 00 06 00 00 01
40 00 7F 00 00 01
* Refer to "System exclusive messages related to mode settings" (p. 4).
40 01 10 00 00 10
40 01 11#
40 01 12#
40 01 13#
40 01 14#
40 01 15#
40 01 16#
40 01 17#
40 01 18#
40 01 19#
40 01 1A#
40 01 :#
40 01 1F#
* The sum total of voices in the voice reserve function must be equal to or less than the number of the maximum polyphony. The maximum polyphony of the HP-337 is 128. For compatibility
with other GS models, it is recommended that the maximum polyphony be equal or less than 24.
40 01 30 00 00 01
40 01 31 00 00 01
40 01 32 00 00 01
40 01 33 00 00 01
40 01 34 00 00 01
40 01 35 00 00 01
* REVERB MACRO is a macro parameter that allows global setting of reverb parameters. When you select the reverb type with REVERB MACRO, each reverb parameter will be set to the most
suitable value.
* REVERB CHARACTER is a parameter that changes the reverb algorithm. The value of REVERB CHARACTER corresponds to the REVERB MACRO of the same number.
|Individual
|Individual
|
|Individual
|
|Bulk
|Bulk
|Bulk
|
Data (H) Parameter
0018-07E8 MASTER TUNE
00-7F MASTER VOLUME
28-58 MASTER KEY-SHIFT
01-7F MASTER PAN
00 MODE SET
00-40 VOICE RESERVE
00-07 REVERB MACRO
00-07 REVERB CHARACTER
00-07 REVERB PRE-LPF
00-7F REVERB LEVEL
00-7F REVERB TIME
00-7F REVERB DELAY FEEDBACK
Description Default Value (H)
-100.0 - +100.0 [cent] 00 04 00 00
Use nibblized data.
0-127 7F
(= F0 7F 7F 04 01 00 vv F7)
-24 - +24 [semitones] 40
-63 (LEFT) - +63 (RIGHT) 40
00 = GS Reset, 127 = Exit GS
(Rx. only)
Part 10 (Drum Part) 02
Part 1 06
Part 2 02
Part 3 02
Part 4 02
Part 5 02
Part 6 02
Part 7 02
Part 8 02
Part 9 02
Part 11 00
:
Part 16 00
00: Room 1 04
01: Room 2
02: Room 3
03: Hall 1
04: Hall 2
05: Plate
06: Delay
07: Panning Delay
0-7 04
0-7 00
0-127 40
0-127 40
0-127 00
Description
0 [cent]
127
0 [semitones]
0 (CENTER)
2
6
2
2
2
2
2
2
2
2
0
0
Hall 2
4
0
64
64
0
9