Honeywell Lyric LCP300-L Quick Installation Manual page 2

Installing the Lyric Gateway (Continued) Installing the Lyric Gateway (Continued) Installing the Lyric Gateway (Continued) Installing the Lyric Gateway (Continued)
WALL
SURFACE
MOUNTING
SCREW
(4) TYP.
REAR
COVER /
MOUNTING
BRACKET
TAMPER
SCREW
Installing & Connecting the Lyric Gateway Installing & Connecting the Lyric Gateway Installing & Connecting the Lyric Gateway Installing & Connecting the Lyric Gateway
9. Within approximately 3 minutes the Gateway will confirm its connection to the WiFi network.
10. Change the Wi-Fi setting of the set up device, to the Gateway AP. Select the Gateway SSID, "OPTGW_####"
(#### = Last 4 digits of the Gateway MAC ID#)" from the list of options and select "Connect". Enter the
Gateway's 8-digit, case sensitive, WPA2 password when prompted and select Connect. (The Gateway SSID
and Password are located on the bottom of the Gateway.)
11. Open the AlarmNet 360 App on the set up device and select "Manage Lyric Gateway".
12. When prompted enter the Installer Code + "Done" + "Submit".
13. The Transfer Firmware, Transfer Panel Configuration, Configure Panel Wi-Fi and Advanced, options appear:
a. Select "Transfer Firmware" to transfer the latest firmware to the Gateway.
b. Select "Transfer Panel Configuration" to transfer the panel configuration set up in AlarmNet 360 to the
Gateway.
c. Select "Configure Panel Wi-Fi" to connect the Gateway to the customer's router.
Enter the customer's SSID and WPA2 password when prompted.
d. Select "Advanced" to access Installer tools. Refer to the Installation and Reference Guide for additional
information.
14. Select "Finish" when configuration is complete.
15. Select "Yes" to exit from the App. The Gateway exits from AP Mode and reconnects to the Wi-Fi network.
16. Select "Proceed to Panel Configuration".
17. Log in to AlarmNet 360.
Programming the Lyric Gateway Programming the Lyric Gateway Programming the Lyric Gateway Programming the Lyric Gateway
The Lyric Gateway is programmed via AlarmNet 360 using a laptop, smart phone or other internet connected
device. There are numerous options for programming the Gateway, Sensors, Wireless Keys and Keypads, Z-Wave®
Home Automation Devices and accessories.
Before you begin Before you begin Before you begin Before you begin
1. Log on to the AlarmNet 360 website (http://alarmNet360.com) or the AlarmNet 360 app, with your User Name,
Password and account information to Program the Lyric Gateway, Sensors and Communications Modules.
Programming Programming via AlarmNet 360 App Programming Programming via AlarmNet 360 App via AlarmNet 360 App via AlarmNet 360 App
1. At the Installer Programming screen, enter the required information.
2. When programming is complete select "
Selecting a Default Configuration Selecting a Default Configuration Selecting a Default Configuration Selecting a Default Configuration
The Lyric Gateway is pre-programmed at the factory with a built-in set of default values. Refer to the Programming
Default Values section to view the pre-programmed values.
REAR COVER /
MOUNTING
BRACKET
SCREW
1
Installing the Desk Mount Installing the Desk Mount
Installing the Desk Mount Installing the Desk Mount
" to Sync Changes and send the information to the gateway.
- 2 -
RJ45 ETHERNET POWER SUPPLY
RECEPTACLE RECEPTACLE
BATTERY
RECEPTACLE
MICROSWITCHES
DETAIL A
1
Wiring Table Wiring Table Wiring Table Wiring Table
Maximum Distance Maximum Distance
Maximum Distance Maximum Distance
Between Power Between Power Between Power Between Power
Supply and Supply and Wire Wire
Supply and Supply and Wire Wire
Gateway Gateway Gateway Gateway Gauge Gauge Gauge Gauge
Up to 8 ft (2.44 m) # 22
Up to 13 ft (3.96 m) # 20
Up to 20 ft (6.1 m) # 18
Recessed Recessed Recessed Recessed
Microswitch Functions Microswitch Functions
Microswitch Functions Microswitch Functions
Location Location Location Location Function Function Function Function
Left Factory Default
Center Reboot
Right (WPS)