Advertisement
S
MT/2A - 03.2A UNDERGROUND MOTOR FOR WING GATES UP TO 3,00 m AND 250 Kg
EACH WING - 230Vac
CF/2A - 03.CF
FOUNDATION BOX
Thank you for choosing a SERAI ELETTRONICA product, which we are confident will perform to your requirements.
Please be advised that you are about to fit a system classified as "a power-operated drive designed to move automatic ga-
tes and doors in commercial or residential buildings accessed by vehicles and persons", and as such, the system must be
considered potentially hazardous. By law, you are responsible for rendering this equipment as "safe" as is reasonably pos-
sible.
Installation and maintenance of equipment of this kind must therefore be carried out by skilled, qualified and trained
personnel, working in a professional manner, as provided for by law n. 46/90 and any subsequent amendments and
supplements. The law in question prohibits the construction of these types of systems by non-qualified personnel.
SERAI manufacturing complies with the following legislation:
Applicable directives for the CE marking :
Machines:
Low Voltage:
Electromagnetic Compatibility:
General applicable standards:
Electrical Safety:
Electromagnetic Compatibility - Emissions:
Electromagnetic Compatibility - Immunity:
Apart from the legislation mentioned above, you are also reminded to comply with the following standards during the
installation phase.
General applicable standards:
Safety of electrical systems in non-specialised environments:
Specific product standards applicable:
Safety in the use of power-operated doors - requirements:
Safety in the use of power-operated doors - testing methods:
SERAI products enable users to build systems which comply with these standards. This is extremely important as
!
THE INSTALLER IS LIABLE FOR THE SYSTEM AND FOR ENSURING ITS OPERATION COMPLIES WITH
LEGAL PROVISIONS.
This handbook must be read in full before proceeding with the installation of the various parts of the system.
The installation of the mechanical end stops for gate opening and closure is necessary for system safety purposes
and therefore this operation must be performed before proceeding with the installation of the control unit.
E
R
GATE AUTOMATION DIVISION
INSTALLATION MANUAL
98/37/EEC
73/23/EEC
89/336/EEC
IEC EN60335-1 + IEC EN60335-2-103
CEI EN61000-6-3
CEI EN61000-6-
CEI 64-8
UNI EN12453
UNI EN12445
A
I
Pag. 1/5
Advertisement
Table of Contents
Related Manuals for Serai MT/2A
Summary of Contents for Serai MT/2A
- Page 1 FOUNDATION BOX Thank you for choosing a SERAI ELETTRONICA product, which we are confident will perform to your requirements. Please be advised that you are about to fit a system classified as “a power-operated drive designed to move automatic ga- tes and doors in commercial or residential buildings accessed by vehicles and persons”, and as such, the system must be...
-
Page 2: Standard Installation
4 x 0,5 mm² 2 x 0,5 mm² 4 x 0,5 mm² M/10 electric key Geared motor MT/2A Pair of P/10 photocells CR/41 electronic control unit with built-in receiver RZ/20 F Flashing light with antenna OG/62 2-channel minitransmitter Advice for wiring up in non-specialised environments. - Page 3 INSTALLATION To operate a good installation of the gear motor MT/2A follow these instructions: Make sure that the leaves of the gate are perfectly horizontal Locate inside the property the correct point to install the gear motors remembering that: the pins “P1” which comes out of the boxes must be always aligned with the rotation axis of the leaves (pivot) (fig.
- Page 4 IMPORTANT: USE THE PROPER GREASER TO IMPORTANT: LUBRICATE PERIODICALLY THE GREASE THE BOLT -EVERY 6 MONTHS BOLT BEFORE FITTING THE LEVER GROUP Pag. 4/5...
-
Page 5: Technical Specifications
TERMS OF GUARANTEE The company reserves the right to make modifications to the equipment without prior notice thereof. SERAI products are covered by a standard guarantee with a term of 24 months. Coverage starts on the date on which the tax document constituting proof of purchase is issued and guarantee services shall be provided on the company's premises at Legnaro - PD - or at the Authorised Service Centres.
Need help?
Do you have a question about the MT/2A and is the answer not in the manual?
Questions and answers