Blizzard 760HD Installation Instructions & Owner's Manual page 4

SAFETY DEFINITIONS
WARNING
Indicates a potentially hazardous situation,
that if not avoided, could result in death or
serious personal injury.
CAUTION
Indicates a potentially hazardous situation
that, if not avoided, may result in minor or
moderate injury. It may also be used to alert
against unsafe practices.
NOTE: Indicates a situation or action that can lead
to damage to your snowplow and vehicle or other
property. Other useful information can also be
described.
MOUNT INSTRUCTIONS
Read Owner's Manual for Complete Instructions.
STEP #1
CONNECT/DISCONNECT
POWER HITCH Switch
Pushbeam
Receiver
Mount Points
Undercarriage
Kickstand Pin
Pushbeam
Slowly Move
Adjustable
Vehicle Forward
Kickstand A-Frame POWER
HITCH Arm
Mount Bushing
WARNING: Keep fingers away. POWER HITCH arm raises behind undercarriage pushbeam.
• Kickstand must be lowered, with kickstand pin seated in lower hole on pivot beam.
• Slowly drive vehicle forward until pushbeam receiver mount points contact
A-frame mount bushings.
• Turn POWER HITCH OPERATION switch (on plow control) to "ON" position.
• Connect plow and vehicle electrical harnesses. Connect weather caps together.
STEP #2
A-Frame
Hitch
Latch
Pin
A-Frame
Latch
Lock Pin
A-Frame Latch
rotates clockwise
and hooks onto
Draw Pin Draw
Pin
• Pull A-frame latch lock pin out and lower A-frame latch over draw pin.
• Push and hold CONNECT/DISCONNECT switch upward. POWER HITCH arm
will engage back of pushbeam and pull plow into pushbeam receiver mount
points on vehicle.
• Insert both hitch pins and secure each with hair pin cotter.
• Lower POWER HITCH arm to relieve tension on A-frame latch. Raise A-frame
latch and lock into position with lock pin. Raise plow.
• Raise kickstand until kickstand pin seats into upper hole on pivot beam.
U.S. Patents 5,638,618; 5,899,007; 6,178,669; 6,276,076; 6,393,737; 6,408,549; 6,412,199; 6,442,877; 6,615,513; Canadian and other patents pending.
Lit. No. B64090, Rev. 07
SAFETY
DISMOUNT INSTRUCTIONS
Read Owner's Manual for Complete Instructions.
STEP #1
CONNECT/DISCONNECT
POWER HITCH Switch
Hitch
Pin
Adjustable
Kickstand Pin
Kickstand
POWER
HITCH Arm
• Raise plow. Lower kickstand until kickstand pin is seated in lower hole on pivot beam.
• Lower plow on flat, level surface. Turn vehicle ignition off.
• Remove hitch pins from A-frame and undercarriage.
• Turn vehicle ignition on.
• Turn POWER HITCH OPERATION switch (on plow control) to "ON" position.
STEP #2
CONNECT/DISCONNECT
POWER HITCH Switch
Kickstand Pin Slowly
Move Vehicle
Adjustable
Backward
Kickstand
POWER HITCH Arm
WARNING: Keep fingers away from plow and truck mounting points.
• Push and hold CONNECT/DISCONNECT switch downward. POWER HITCH
arm will disengage from behind undercarriage pushbeam and lower.
• Disconnect plow and vehicle electrical harnesses. Install weather caps.
• Turn SYSTEM POWER (on plow control) to "OFF" position.
• Slowly move vehicle backward away from plow.
WARNING/CAUTION & INSTRUCTION
LABELS
Become familiar with and inform users about the
warning and instruction labels on the back of the
blade.
NOTE: If labels are missing or cannot be read, see
your sales outlet.
LOWER BLADE WHEN VEHICLE IS PARKED.
DO NOT EXCEED GVWR OR GAWR INCLUDING BLADE
AND BALLAST.
REMOVE BLADE ASSEMBLY BEFORE PLACING
VEHICLE ON HOIST.
READ OWNER'S MANUAL BEFORE OPERATING OR
SERVICING SNOWPLOW.
TRANSPORT SPEED SHOULD NOT EXCEED 45 MPH.
FURTHER REDUCE SPEED UNDER ADVERSE TRAVEL
CONDITIONS.
PLOWING SPEED SHOULD NOT EXCEED 10 MPH.
SEE YOUR SALES OUTLET/WEB SITE FOR SPECIFIC
VEHICLE APPLICATION RECOMMENDATIONS.
44812
4
WARNING
CAUTION
WARNING WARNING
Crush Crush
hazard. hazard.
Keep feet Keep feet
clear. clear.
June 15, 2010
59900