Philips DVP3200V/75 Service Manual page 105

DISASSEMBLY/ASSEMBLY PROCEDURES
Before following the procedures described below, be sure to remove the deck assembly from the cabinet. (Refer to
CABINET DISASSEMBLY INSTRUCTIONS of Main Section.)
All the following procedures, including those for adjustment and replacement of parts, should be done in Eject
mode; see the positions of [41] and [42] in Fig. DM1 on page 2-4-3. When reassembling, follow the steps in reverse
order.
STEP START-
/LOC. ING
No. No.
[1] [1] Guide Holder A
Cassette Holder
[2] [1]
Assembly
[3] [2] Slider (SP)
[4] [2] Slider (TU)
[5] [4] Lock Lever
[6] [2] Cassette Plate
[7] [7] Cylinder Assembly
[8] [8] Loading Motor Assembly T
[9] [9] ACE Head Assembly
Tape Guide Arm
[10] [2]
Assembly
[11] [10] C Door Opener
[12] [11] Pinch Arm (B)
[13] [12] Pinch Arm (A) Assembly
[14] [14] FE Head
[15] [15] Prism
[16] [2],[15] Sensor Gear
[17] [2] Slider Shaft
[18] [17] C Drive Lever (SP)
[19] [17] C Drive Lever (TU)
[7],[8],
[20] Capstan Motor
[10]
[21] [21] Clutch Assembly
[22] [22] Cam Holder Assembly
[23] [23] Cam Gear (B)
[24] [24] Mode Gear
[21],[23],
[25] Mode Lever
[24]
[26] [22] Worm Holder
[27] [26] Pulley Assembly
[28] [25],[26] Cam Gear (A)
[29] [25] Idler Gear
[30] [29] Idler Arm
[31] [25] BT Arm
OF DECK MECHANISM
PART
Fig. No.
T DM3
T DM4
T DM5
T DM5
T DM5
T DM5
T DM1, DM6
DM1, DM7
T DM1, DM7
T DM1, DM8-1
T DM1, DM8-1
DM1, DM8-1,
T
DM8-2
DM1, DM8-1,
T
DM8-2
T DM1, DM9
T DM1, DM9
T DM1, DM9
T DM10
T DM10
T DM10
B DM2, DM11
B DM2, DM12
B DM2, DM12
B DM2, DM12
B DM2, DM13-1
DM2, DM13-1,
B
DM13-2
B DM2, DM13-1
B DM2, DM13-1
DM2, DM13-1,
B
DM13-2
B DM1, DM14
B DM1, DM14
B DM2, DM14
REMOVAL
REMOVE/*UNHOOK/
UNLOCK/RELEASE/
UNPLUG/DESOLDER
2(S-1)
(S-1A), *(L-1)
*(L-2)
*(L-3), *(P-1)
Desolder, 3(S-2)
Desolder, LDG Belt,
2(S-3)
(S-4)
*(P-2)
(S-4A), *(L-4)
*(P-3)
(S-5)
(S-6)
*(L-5)
(S-7), *(P-4)
3(S-8), Cap Belt
(C-1)
*(L-6)
(C-2), *(P-5)
(C-3)
(C-4), *(L-8)
(S-9), *(L-9), *(L-10)
*(L-11)
*(P-6)
2-4-1
INSTALLATION
ADJUSTMENT
CONDITION
U29PDA