Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Q Set Aviator CN-1000AC-BT
- Page 1 User Manual...
- Page 2 Contents Introduction Prepare Headset for Use Operation Installing Batteries Mode Settings Bluetooth Disassembly Parts List Schematic Diagram Specifications...
-
Page 3: Introduction
Introduction _________ ANR Instruction: The Active Noise • ANR Active Noise ReductionLight weight 11oz. Reduction CN-1000AC-BT Headset is a headset that can isolate, offset and • Soft leather ear-pads cancel noise. In comparison with pas- • Carbon Fiber Construction sive headsets, it can, under noisy cir- •... -
Page 4: Prepare Headset For Use
Prepare Headset for Use 1. Rotate the flexible boom overhead to wear the microphone on either the right or left side of the head. 2. Rotate the headset volume control (on the side of the battery box) down to the mini- mum position, before the headset plug is inserted into the aircraft or intercom. -
Page 5: Operation
Operation Insert or change Batteries: Two AA batteries power the Q Set Aviator. ①press from the base of the triangle on the cover, see Figure 1;②push the cover out of the safety lock, see Figure 2;③tilt the end of the cover up and remove the whole cover;... -
Page 6: Mode Settings
S/M switch: There is an s / m switch inside the battery box, see Figure 4. Ensure the switch is on Mono to make both ears active (on most aircraft). Light Indication for Power: Press power button for 0.5 seconds, ANR starts working. -
Page 7: Bluetooth
Bluetooth works when the mode setting switch is positioned on A or B. Bluetooth volume control: Press “+” or “-” to turn up or down the volume of blue tooth connected device. Holding “+” or “-” will keep the volume up or down, see Figure 5 Pairing: device name—BT-ANR;... - Page 8 Clearing the pairing record: press both Bluetooth volume control buttons on the side for 3 seconds. Making calls: dial the number on your phone. Click the Bluetooth button twice to return the last incoming call. Receiving calls: Press the Bluetooth button and answer the call after the BEEP.
- Page 9 Turn Off ANR: Press power button for 2 seconds to turn ANR off. Notice: 1.Use non-rechargeable alkaline AA batteries. 2.Shut the power off when ANR is not in use. 3.Take out the batteries if ANR is left unused for a long period.
-
Page 11: Parts List
Parts List ITEM DESCRIPTION 10ME0069 RETAINING RING 10PL0038 RIGHT CARBON EARCUP 10SP0055 ABSORBENT NOISE FILTER (1) 10SP0056 ABSORBENT NOISE FILTER (2) 10EL0046 NOISE CANCELING PCB (RIGHT) 10SP0049 PROTEIN LEATHER EARSEAL 10EL0047 NOISE CANCELING PCB (LFET) 10CR0020 OVERHEAD CORD 10ME0068 HEADBAND , STAINLESS STEEL 10SP0005 HEADBAND CUSHION 10KI0020... - Page 12 ITEM DESCRIPTION 10ME0010 STIRRUP 10PL0004 GROMMET , RUBBER 10KI0037 MIC BOOM ATTACHMENT KIT 10KI0036 FLEXIBLE BOOM ASSEMBLY 10EL0045 ELECTRET MICROPHONE 10SP0054 MICROPHONE WINDSCREEN 10PL0008 O RING 10PL0005 STRAIN RELIEF 10CR0004 COMM CORD , STRAIGHT 10SP0021 SELF-GRIPPING FASTENER 10KI0038 BT BATTERY MODULE 10CR0005 5.2 MOLDED PLUG CORD（PJ068）...
-
Page 13: Schematic Diagram
Headset Schematic Diagram... -
Page 14: Specifications
Specifications Noise Reduction Ratings Speech Sound: （ ）： 23dB Dynamic 300 ohms: Noise Reduction Ratings Rate Input: 30mW Max. Input: 100mW （ ）： 29dB Headphone Microphone and Amplifier: Type: Dynamic （Φ30） Element Type: Noise-canceling electret Frequency Response: 50 Hz to 20 kHz Frequency Response: 100Hz to 5 kHz Sensitivity: 95±5 dB SPL Operating Voltage (supplied by air-... - Page 15 General: Main Attenuation Frequency Band ….20Hz~600Hz Temperature: Operating: - 20 to 70°C Attenuation Capability…….… Cordage: Straight cord from headset to ……..29dB molded plug, 150CM Power Consumption ……. ………...30 Intercom Connections: Earphone Plug： PJ-055 (.25” 6.3Φ Headset size range Height: 10 to 14 cm phone plug) Color: Black Boom: Flexible Boom Microphone Plug：...
- Page 16 Manufactured in China and distributed by: Designs & Consultations Brandon, Manitoba, Canada R7A 2J9 1-204-726-4221 rsdesign@mts.net...