Primera Max Connectivity Manual
Optical disc laminator
Hide thumbs
Also See for Max:
- Connectivity manual (20 pages) ,
- User manual (44 pages) ,
- User manual (44 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Primera Max
Summary of Contents for Primera Max
- Page 1 012004-510887-(01) XL/Pro Optical Disc Laminator Connectivity Guide © 2004 All rights reserved.
- Page 2 Notices: The information in this document is subject to change without notice. NO WARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No liability is assumed for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
-
Page 3: Table Of Contents
A. Unpacking and Inspection ...1 B. Installing the Laminator Software Driver...1 C. Connecting the Laminator to Your Duplicator ...3 D. Creating Discs with Your Duplicator MAX in Primo ...7 E. Connecting the Laminator to Your Duplicator XL/Pro ...7 Stand-Alone Mode...8 Full Production Mode ...11... -
Page 5: Optical Disc Laminator Guide
Thank you for purchasing the Optical Disc Laminator Connectivity Kit. This kit will allow you to use your Optical Disc Laminator in conjunction with the Pro, XL and MAX versions of Optical Disc Duplicators. This guide will explain the connection of the Laminator to these systems, the installation of software and the running of disc jobs. - Page 6 Make certain the Laminator has been plugged into power and turned on. Select "Install Software Automatically" and click Next. 2 Optical Disc Laminator Connectivity Guide...
-
Page 7: Connecting The Laminator To Your Duplicator
You may see a notice like the one shown here stating that the Accent Disc Laminator has not passed Windows Logo Testing. Click the Install Anyway button to continue installing the printer driver for your Laminator. Once the driver has finished installing, click the Finish button. - Page 8 The following steps describe in detail how to connect the Laminator to your DuplicatorMAX: a. Connect the Laminator Stand to the left hand side of the DuplicatorMAX as shown: b. Remove the Input Bin closest to the Laminator Stand to make room for the Laminator's disc tray.
- Page 9 7) Click the button labeled Move to (Calibrate). This will move the Picker Mechanism to the Laminator Tray position. 8) Lower the disc to the Laminator Tray Position as follows: a) Press and hold the Sequence and Pick buttons simultaneously for 5 seconds to enter calibration mode.
- Page 10 While the LEDs are flashing, press the Pause button. The Picking Mechanism will lower to the Laminator Tray Position. c) Adjust the Laminator Tray forward and back by loosening the adjusting screws located towards the front of the stand.
-
Page 11: Creating Discs With Your Duplicator Max In Primo
Options. Enable the Use Laminator checkbox as shown: 2. Set up your print and record job as you normally would per the instructions in the Duplicator MAX User Manual. 3. Click the Red Circle Record button to start your job! E. -
Page 12: Stand-Alone Mode
The Laminator is positioned at the front left corner of the Duplicator. The optional Duplicator XL/Pro Laminator Stand is needed for both of these configurations. The stand is shown here: STAND-ALONE MODE The Automated Stand-Alone Mode allows you to connect the Laminator to the Duplicator XL or DuplicatorPro without connecting either the Duplicator or Laminator to a PC. - Page 13 4. Connect the Laminator Stand to the back of the Laminator as shown: 5. Place the Laminator on the Laminator Stand as shown: There are two sets of holes on the underside of your Laminator. Set the Laminator on the stand locating the smaller set of holes on the metal locating pegs on the Laminator Stand.
- Page 14 6. Connect the Auxiliary Control Cable and Power Cable the Laminator as shown: 7. Align the Laminator's tray position to the picker. This is done as follows: a. Make certain the Laminator has power and is turned on. b. Load a disc into the Input Bin. This is the Bin on the right side of the Duplicator.
-
Page 15: Full Production Mode
Input Bin is empty. NOTE: If the Picking Mechanism will not pick a disc from the Laminator Tray, make certain the Laminator is sitting on the Stand correctly. The Laminator's Rubber Feet should be resting on the stand, not in the four holes located on top of the stand. - Page 16 4. Place the Laminator on the stand. The Laminator will need to be placed on the stand with the Laminator's rubber feet resting in the four holes located on the top of the Stand as shown: 5. Using the provided USB Cable, connect the Laminator to your PC as shown: 6.
- Page 17 NOTE: If the Picking Mechanism will not pick a disc from the Laminator Tray, make certain the Laminator is sitting on the Stand correctly. The Laminator's Rubber Feet should not rest on the stand but in the four holes located on the top of the stand.
- Page 18 Options. Select Lamination as shown: 9. Set up your print and record job as you normally would per the Duplicator XL/Pro User's Manual. 10. Click the red circle Record button to start your job! 14 Optical Disc Laminator Connectivity Guide...
-
Page 19: Troubleshooting
If you have difficulties in operating your Laminator, the procedures in this manual should, in most cases, solve the problem. If you still have difficulty, call Technical Support at the number listed on the insert in your Laminator suppy pack. Resolution Check Power to the Laminator •... - Page 20 Printed in the United States of America P/N 510887...
Need help?
Do you have a question about the Max and is the answer not in the manual?
Questions and answers