Toshiba 27A41 Service Manual page 11

更多难得资料请到江南家电维修论坛免费下载！
http://bbs.520101.com
2-7: VERTICAL LINEALITY
NOTE: Adjust after performing adjustments in section 2-6.
1. Receive the center cross signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (09) on the remote control to
select "V. LIN".
4. Press the VOL. UP/DOWN button on the remote
control until the upside and downside screen size of the
horizontal line becomes the same.
2-8: VERTICAL POSITION
NOTE: Adjust after performing adjustments in section 2-7.
1. Receive the center cross signal from the Pattern
Generator.
2. Adjust the VR401 until the horizontal line becomes fit to
the notch of the shadow mask.
2-9: VERTICAL SIZE
NOTE: Adjust after performing adjustments in section 2-8.
1. Receive the crosshatch signal from the Pattern
Generator.
2. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (07) on the remote control to
select "V. SIZE".
3. Press the VOL. UP/DOWN button on the remote
control until the rectangle on the center of the screen
becomes square.
4. Receive a broadcast and check if the picture is normal.
2-10: OSD HORIZONTAL
1. Activate the adjustment mode display of Fig. 1-1.
2. Press the VOL. UP/DOWN button on the remote control
until the difference of A and B becomes minimum.
(Refer to Fig. 2-1)
00 OSD
A
2-11: LEVEL
1. Receive a 70dB monoscope pattern.
2. Connect the AC voltmeter to TP901.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (30) on the remote control to
select "LEVEL".
4. Press the VOL. UP/DOWN button on the remote
control until the AC voltmeter is 75 ± 2mV.
ELECTRICAL ADJUSTMENTS
TV
15
B
Fig. 2-1
2-12: SEPARATION 1, 2
1. Receive the stereo signal (L=2KHz, R=400Hz).
2. Connect the AC voltmeter to AUDIO OUT JACK though
stereo filter (L=400Hz, R=2KHz).
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (31) on the remote control to
select "SEP1".
4. Press the VOL. UP/DOWN button on the remote control
until the output of L-CH and R-CH become minimum.
5. Press the CH UP button once the set to "SEP2" mode.
6. Press the VOL. UP/DOWN button on the remote control
until the output of L-CH and R-CH become minimum.
7. Press the CH DOWN button once the set to "SEP1"
mode.
8. Repeat step 4 to step 7 several times.
The output difference of the between with Filter and
without Filter should be more than 25db for both L and R.
2-13: BRIGHTNESS
1. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "BRI".
2. Press the VOL. UP/DOWN button on the remote control
until the brightness step No. becomes "92"
3. Press the TV/VIDEO button on the remote control to set
to the AV mode. Then perform the above adjustments
1~2.
4. Press the TV/VIDEO button on the remote control to set
to the CS mode.
5. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "BRI".
6. Press the VOL. UP/DOWN button on the remote control
until the brightness step No. becomes "90"
2-14: UNI-COLOR
1. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (18) on the remote control to
select "UNI COL".
2. Press the VOL. UP/DOWN button on the remote control
until the contrast step No. becomes "54"
3. Press the TV/VIDEO button on the remote control to set
to the AV mode.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (18) on the remote control to
select "UNI COL".
5. Press the VOL. UP/DOWN button on the remote control
until the contrast step No. becomes "58"
6. Press the TV/VIDEO button on the remote control to set
to the CS mode.
7. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (18) on the remote control to
select "UNI COL".
8. Press the VOL. UP/DOWN button on the remote control
until the contrast step No. becomes "60"