Table of Contents
Advertisement
For
For
For
For
For
For
F F F F
F
F
For Installation Help
or
Installation
Installation
Installation
Installation
Installation
Installation
Installation
1 1 -877-654-9394
1-877-654-9394
877 654 9394
White-Rodgers.com
White-Rodgers.com
© 2011 Printed in China
Help
Help
Help
Help
Help
Help
Help
White-Rodgers
8100 West Florissant Avenue
St. Louis, MO 63136
0037-7258A
UNP300 Non-Programmable Thermostat
with Home / Sleep / Away Presets
Installation Instructions & User Guide
Congratulations on the purchase of your White-Rodgers
Save these instructions for future use!
Questions? Contact White-Rodgers
customer service at 1-877-654-9394
™
thermostat!
™
Advertisement
Table of Contents
Related Manuals for White Rodgers UNP300
Summary of Contents for White Rodgers UNP300
- Page 1 UNP300 Non-Programmable Thermostat with Home / Sleep / Away Presets Installation Instructions & User Guide For Installation Help F F F F Installation Installation Installation Installation Installation Installation Installation Help Help Help Help Help Help Help 1-877-654-9394 1 1 -877-654-9394 877 654 9394 White-Rodgers.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Part 1: Before Getting Started ............Page 2 • Failure to read and follow all instructions carefully before installing 1.1 Check package contents or operating this control could cause personal injury and/or 1.2 Answer questions about source of heating in your home property damage. -
Page 3: Part 1 Before Getting Started
1.2 Answer questions about source of Part 1 Before Getting Started heating in your home Before getting started, please review the following ✔ Do you have either oil or gas burning furnace? pre-installation checklist. ✔ Do you have a Heat Pump (and is it 1-stage or 2-stage)?* ✔... -
Page 4: Part 2 Remove Old Thermostat And Install New Thermostat
3-Part unit Part 2 Remove Old Thermostat and Install New Thermostat Do not disconnect wires from the old thermostat until you label all the wires according to this manual. Cover Base Wallplate 2.1 Expose wires connected to 2-Part unit old thermostat 2.1.1 After turning off power to your heating &... -
Page 5: Label And Disconnect The Wires
2.1.2 Loosen all screws holding the old thermostat’s wallplate to 2.2 Label and disconnect the wires the wall. Do not disconnect the wires from terminals. Allow the wallplate to hang loosely on the wires. 2.2.1 Note you may see two types of wiring in the old thermostat: 1. - Page 6 If the OLD thermostat’s 2.2 Label and disconnect the wires (cont.) …Then label its wire with terminal is wired into the wall this letter: and identifi ed by this letter… 2.2.2 Label each wire that comes out of the wall and attaches to terminals on the old thermostat.
-
Page 7: Install New Thermostat's Wallplate
2.2.3 After labeling all the wires, use a screwdriver to disconnect 2.4 Match and connect wires each wire from its terminal. Remove the old thermostat. 2.4.1 Match each wire coming from the wall to its corresponding Make sure that the wires don’t fall terminal, as shown in the illustration below. -
Page 8: Install Additional Wiring (For Heat Pumps Only)
2.5 Install additional wiring 2.6 Set Switches (for Heat Pumps only) Find two switches located on in the lower right corner of the wallplate labeled ELE/GAS and O/B. Set them as follows: If your HVAC system does NOT include a Heat Pump, continue to 2.6. •... -
Page 9: Part 3 Quick Setup
3.2 Set fan and system switches Part 3 Quick setup 1. Open the door on the right side of the cover and locate the FAN and SYSTEM switches. 3.1 Get to know your thermostat 2. Set the FAN switch to AUTO. 3. -
Page 10: Select Options
3.3 Select options Options Default Setting Additional Information 3. Do you want the Select SL (slow) if you Press the MENU button and, using the buttons, scroll down until Cycle Rate to be (fast) have Hydronic (water MORE OPTIONS is fl ashing. Press OK. Fast or Slow? or steam) Heating. -
Page 11: Part 4 Additional Thermostat Features
4.2 Change batteries Part 4 Additional thermostat features The thermostat displays battery life in three stages: 4.1 Set favorite temperatures • Battery full (home / sleep / away) • Battery half-full You can set your three most frequent temperatures (Home, Sleep, •... -
Page 12: Set Keypad Lockout
4.4 Set keypad lockout 4.5 Set change fi lter reminder The thermostat will display a reminder when it is time to change the air To activate: fi lter on your heating and cooling system. Press and hold the OK button for 3 seconds to lock the keypad. The keypad lock icon will appear on the display. -
Page 13: Adjust Actual Temperature Display
4.6 Adjust actual temperature display Part 5 Troubleshooting Guide Your thermostat was accurately calibrated at the factory. However, if you would like the displayed temperature to read higher or lower than Problem Possible Cause Action the actual temperature, you can adjust the displayed temperature Temperature set 2-minute lockout No action needed: should... -
Page 14: Appendix: Heat Pump Identifi Cation
5 Troubleshooting Guide (continued) Appendix: Heat Pump Identifi cation Reset Operation If a voltage spike or static discharge blanks out the display or causes erratic thermostat operation, you can reset the thermostat 1. How do I know if I have a Heat Pump? by pressing all three buttons (HOME, and both ) simultaneously...