Putting The Machine In Operation; Instructions For Operating The Mowing Machine; Replacing The Mowing String; Adjusting The Mowing String - IKRA Mogatec Gartenmeister GM ART 4030 Operating Instructions Manual

within the dimensions of the unfolded bar. However, the
trimmer can also be operated with the bar folded up if
required.
Installing the guide wheel (edge trimming) (fig. 3)
• Attach the wheel (10) to the mount from above.

Putting the machine in operation

• Insert the charged battery in the trimmer until the in-
terlock latches. The rechargeable battery can only be
inserted in the trimmer in one position.
Attention: When inserting the battery do not actuate
the switch-on inhibit (8) and the on/off switch (9).
• Adopt a safe stand. Hold the trimmer in both hands.
Do not set the cutting device down on the ground.
• Press the switch-on inhibit (8) to the left or right and
actuate the switch (9). After switching on, the switch-
on inhibit (8) must no longer be held.
• In order to switch off, release the switch (9) (Fig. 5).
Directions for set length adjustment and the
use of the set as edge cutter
The tube length may be adjusted to suit your height
(Fig. 6)
• To do so, turn the ribbed plastic sleeve clockwise to
loosen the connection. Adjust the tube to the suitable
length and fasten the connection by turning the tapped
sleeve anti-clockwise.
Adjusting the tilting angle (Fig. 7):
• Press the button (3) - the trimmer head is disengaged
and can be pivoted in four positions relative to the
shaft.
Adjusting for edge trimming (Fig. 8):
• Press button (11): The trimmer head may now be
turned 90°.

Instructions for operating the mowing machine

(fig. 9)
• Move the mowing machine evenly from oneside to
another.
• If possible, mow by using the left half of the mowing
machine. The mowed parts of plants and / or stones
will thus be hurled forward away from the operating
person.
• The best possible cutting result are achieved when
you hold the trimmer with an angle of 20°- 30° to
the left side.
• Avoid contact between the mowing string and obsta-
cles such as fences, walls, stones, etc. This leads to
excessive wear and tear.

Replacing the mowing string

Attention - risk of injury! Always remove the re-
chargeable battery from the device before all work.
GB | Operating Instructions
(Fig. 4+5)
(Fig. 6, 7 and 8)
(fig. 10 - 11)
GB-6
Push the two locking devices (13) at the sides of the
cutting head, and remove the cutting head cover (12).
Remove the used thread coil and put in the new coil (14)
such that the end of the thread comes out of the outlet
(15) at the side of the cutting head (Fig. 10+11). Finally,
close the cover by pushing it in its seat. Both locks must
properly engage.
A replacement spool may be stored in a hinged compart-
ment on the grip housing (fig. 12).
To open the compartment cover, pull firmly on the
marked positions. After the spool has been removed,
replace the cover firmly.

Adjusting the mowing string

• Whenever the mowing performance decreases, it is
necessary to adjust (to extend) the mowing string.
• Turn the mowing machine on and hold it above the
grass.
• With the motor running, knock the head on the grass
(fig. 13). The string will automatically extend and the
cutting device will reduce it down to the right length.
Note: If the string is shorter than 2.5 cm, it is necessary
to adjust it manually. Press the red push-button on the
coil until it reaches the stop and pull the end of the string.
If you cannot see the end of the string at all, proceed as
described in „Replacing the Mowing String".

Trouble shooting

• Cutting line disappears into spool: Remove spool,
pull end of line through the metal outlet and reinsert
spool. In case nylon line is used up insert a new spool
with line.
Do not make any other repairs on your own; have
your trimmer checked and repaired by an authorised
dealer.

Maintenance and care

Attention - risk of injury! Always remove the re-
chargeable battery from the device before all work.
Clean your battery-operated mowing machine thoroughly
each time after you use it. Remove the grass and dirt.
Clean the ventilation openings. It is best to clean the
plastic parts with a wet cloth and a soft detergent. Never
use aggressive detergents or solvents. Do not pour water
into the machine and do not sprinkle it with water. Store
the mowing machine in a dry place, never expose it to
frost and keep it out of children's reach.
For more extensive maintenance or repairs, give the
mowing machine to the service center.

Repair service

Repairs to electric power tools should only be carried out
by a specialised electrician.
(fig. 13)