Setting the Program Mode ....................12 Interfacing with Manual Control ..................17 Troubleshooting ........................ 17 Special Conditions in Program Mode ................18 Pairing Remote Handset & Control Box ID Code ............19 Warning & Cautions ......................19 Page 2 FPI FireGenie Remote Control Manual...
The FireGenie Remote Control was developed to provide a user-friendly system to use your appliance. The operating range is approximately 10 metres. A Quick Reference Sticker is available to be placed on the back of your remote control handset. Place the sticker close to the very top of the remote, away from the battery opening and wall mounting bracket.
1/PROG 2. Fan 1 and Fan 2 selected indication “1/2”. 9. Temperature Display in “ºC” or “ºF”; 10. Fan Speed Indication (3 different fan speeds); 11. Time of Day with AM, PM; 12. Room Temperature and Set Temperature display. Page 4 FPI FireGenie Remote Control Manual...
The On/Off button is used to switch the Remote ON or OFF. If the Remote is switched OFF, pressing and releasing the On/Off button will switch ON the Remote (and the FireGenie Control Box). Once switched ON, the Remote will resume with its last selected operating mode, for example, Manual, Auto or Program mode.
3. While the “-” button is held down, press and release the “+” button, this will toggle the temperature display between °C and °F. This setting is stored in memory hence the Remote will continue to display the temperature in Fahrenheit even if the battery is replaced. Page 6 FPI FireGenie Remote Control Manual...
Note: Fan 1 and Fan 2 cannot be turned off while heater is in operation. The LCD will display as follows: (a) Normal Display – The LCD will show the fan speed of the last selected fan, with can be Fan 1 or Fan 2. FPI FireGenie Remote Control Manual Page 7...
Page 8
(b) When the Fan 1 button is pressed while fan 1 is at low speed, the LCD will display as follows: (c) Similarly when the Fan 2 button is pressed while fan 2 is at low speed, the LCD will display as follows: Page 8 FPI FireGenie Remote Control Manual...
When the room temperature is lower than the set temperature by more than 2.5°C, the flame and fans will automatically start, the flame will be at the highest setting (6) and the fan speed will default to the lowest setting (1). FPI FireGenie Remote Control Manual Page 9...
Page 10
Fan speeds can be adjusted by using the Fan 1 and Fan2 buttons, as in Manual Mode. Room Temperature Temperature When “+” or “-” button Auto Mode normal display is pressed The minimum Set Temperature is 7°C and the maximum is 32°C. The default Set Temperature is 22°C. Page 10 FPI FireGenie Remote Control Manual...
When “+” or “-” Program 1 mode normal display button is pressed If the Time Zones have not been programmed in the Remote, the display will show the following: Programs have not been set. FPI FireGenie Remote Control Manual Page 11...
The On-Time for Time Zone 1 will also flash. The “+” and “-” buttons can be used to adjust this time setting. The LCD will show the current setting in Time Zone 1 for Monday: Programming of Time Zone 1 Time Zone 1 On-Time Page 12 FPI FireGenie Remote Control Manual...
Page 13
Press and release the AUTO/MAN/PROG button again to program the Set Temperature. Use the “+” and “-” buttons to adjust the temperature setting. Time Zone 1 Set Temperature Programming of Time Zone 1 FPI FireGenie Remote Control Manual Page 13...
Page 14
Press and release the AUTO/MAN/PROG button again to program the Off-Time of Time Zone 2. Use the “+” and “-” buttons to adjust this time setting. The LCD will show the following: Programming of Time Zone 2 Time Zone 2 Off-Time Page 14 FPI FireGenie Remote Control Manual...
Page 15
7b) Alternatively, Copy Programs Over to the Other Days Pressing and holding the PROG button for 2 seconds or longer will initiate the copying process. The next Day of Week flashes Time Zone 1 Setting of Monday FPI FireGenie Remote Control Manual Page 15...
Page 16
8) Exiting Programming Mode The Remote will automatically exit the Programming mode 20 seconds after the last button is released. Pressing the TIME button or the OFF button will exit the programming mode. Page 16 FPI FireGenie Remote Control Manual...
When remote control is in Auto Mode it is important to keep it away from the heater and any extreme heat sources to ensure accurate measurement of room temperature. FPI FireGenie Remote Control Manual Page 17...
1:00 pm, the following will occur: Time Zone 1 On-Time Off-Time 8:00 am 2:00 pm 1:00 pm 4:00 pm On-Time Off-Time Time Zone 2 Operates under Time Zone 1 Operates under Time Zone 2 Setting Setting Page 18 FPI FireGenie Remote Control Manual...
Excessive heat can cause property damage. The fireplace can stay ignited for many hours. Take care to turn off the fireplace if it is unattended by adult people. Keep remote control out of reach of children. FPI FireGenie Remote Control Manual Page 19...
Page 22
Page 22 FPI FireGenie Remote Control Manual...
Page 23
Remote Control and Receiver I.D. Code” on page 19 in the enclosed manual, and follow the coding instructions carefully. Failure to code these together will result in malfunction of the remote control device. FireGenie is a trademark of FPI Fireplace Products International Ltd. Printed in Canada...
Page 24
FireGenie is a trademark of FPI Fireplace Products International Ltd. Printed in Canada...