Related Manuals for FPI FireWizard
Summary of Contents for FPI FireWizard
-
Page 1: Remote Control
REMOTE CONTROL OPERATING INSTRUCTIONS 918-582a 07/11/06 © Copyright 2006, FPI Fireplace Products International Ltd. All rights reserved. FPI FireWizard Remote Control Manual Page 1... - Page 2 Please see the instructions under “Matching Remote Handset and Control Box ID Code”, and follow the coding instructions carefully. Failure to code these together will result in malfunction of the remote control device. FireWizard is a trademark of FPI Fireplace Products International Ltd. IMPORTANT!
-
Page 3: Table Of Contents
Program Mode ... 12 Setting the Program Mode ... 13 Interfacing with Manual Control ... 18 Troubleshooting / Battery Replacement ... 18 Special Conditions in Program Mode ... 19 FPI FireWizard Remote Control Manual TABLE OF CONTENTS 1.1.1. Page 3... -
Page 4: Matching Remote Handset & Control Box Id Code
The control box will only learn the Remote ID codes during the first 30 seconds after power is applied and will ignore this special command from the Remote after the first 30 seconds. NOTE: This must only be performed by a qualified installer. Page 4 FPI FireWizard Remote Control Manual... -
Page 5: Remote Control Keypad
The FireWizard Remote Control was developed to provide a user-friendly system to operate your appliance. The operating range is approximately 10 metres (32 feet). A Quick Reference Sticker is available to be placed on the back of your remote control handset. -
Page 6: Remote Control Screen Display (Lcd)
7. Battery Low Indicator “ ” 8. Programmed Mode Indication “PROG 1” / “PROG 2”; 9. Temperature Display in “ºC” or “ºF”; 10. Fan Speed Indication; 11. Time of Day with AM, PM; Page 6 FPI FireWizard Remote Control Manual... -
Page 7: Quick Reference Of Basic Functions
The On/Off button is used to switch the Remote ON or OFF. If the Remote is switched OFF, pressing and releasing the On/Off button will switch ON the Remote (and the FireWizard continue with its last selected operating mode, for example, Manual, Auto or Program mode. -
Page 8: Manual And Auto Mode
3. While the “-” button is held down, press and release the “+” button, this will toggle the temperature display between °C and °F. This setting is stored in memory hence the Remote will continue to display the temperature in Fahrenheit even if the battery is replaced. Page 8 FPI FireWizard Remote Control Manual... -
Page 9: Manual Mode
Pressing and releasing the FAN button again will switch the Fan OFF. The display on the LCD will be as follows: Fan on Low Speed Fan on Medium Fan on High Speed Fan = OFF Speed FPI FireWizard Remote Control Manual Page 9... -
Page 10: Flame Height Adjustment
If the “+” button is pressed, the rear burner will turn on and the flame can continue to be increased. Page 10 FPI FireWizard Remote Control Manual... -
Page 11: Auto Mode
Room Temperature. The Set Temperature can be adjusted while it is displayed using the “+” and “-” buttons. The LCD will show the following when either the “+” or “-” button is pressed: Auto Mode normal display FPI FireWizard Remote Control Manual AUTO MODE Room Temperature... -
Page 12: Program Mode
If the Programs have not been programmed in the Remote, the display will show the following: Page 12 PROGRAM MODE Room Temperature Temperature Programs have not been set. When “+” or “-” button is pressed FPI FireWizard Remote Control Manual... -
Page 13: Setting The Program Mode
The On-Time for Program 1 will also flash. The “+” and “-” buttons can be used to adjust this time setting. The LCD will show the current setting in Program 1 for Monday: FPI FireWizard Remote Control Manual Programming of Program 1... - Page 14 Press and release the PROG button again to program the Set Temperature. Use the “+” and “-” buttons to adjust the temperature setting. Page 14 Programming of Program 1 Program 1 Off-Time Program 1 Set Temperature Programming of Program 1 FPI FireWizard Remote Control Manual...
- Page 15 Press and release the PROG button again to program the Off-Time of Program 2. Use the “+” and “-” buttons to adjust this time setting. The LCD will show the following: FPI FireWizard Remote Control Manual Programming of Program 2...
- Page 16 Pressing and holding the PROG button for 2 seconds or longer will initiate the copying process. Page 16 Program 2 Set Temperature Programming of Program 2 The next Day of Week flashes Program 1 Setting of Monday FPI FireWizard Remote Control Manual...
- Page 17 Press and release the PROG button to return to normal programming mode. 8) Exiting Programming Mode The Remote will automatically exit the Programming mode 20 seconds after the last button is released. FPI FireWizard Remote Control Manual The next Day of Week flashes Program 1 Setting of Monday and...
-
Page 18: Interfacing With Manual Control
• Ensure the batteries are correctly installed in the receiver. • Check the batteries for replacement (2 x AAA alkaline). When batteries are replaced, only the current time and day will need to be reset. The set program times are not affected. Page 18 FPI FireWizard Remote Control Manual... -
Page 19: Special Conditions In Program Mode
Program 1 is programmed to end at 2:00 pm whereas Program 2 is programmed to commence at 1:00 pm, the following will occur: On-Time 8:00 am Operates under Program 1 Setting FPI FireWizard Remote Control Manual Program 1 Off-Time 2:00 pm 1:00 pm... - Page 20 FireWizard is a trademark of FPI Fireplace Products International Ltd. Printed in Canada Page 20 FPI FireWizard Remote Control Manual...