To Set Parking Brake; Stopping; To Move Forward And Backward; To Adjust Mower Cutting Height - Poulan Pro PR1842STD Owner's Manual

OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which can
result in severe eye damage. Always wear safety glasses or eye shields while operating
your tractor or performing any adjustments or repairs. We recommend a wide vision
safety mask over spectacles or standard safety glasses.
I
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE
(See Fig. 6)
Your tractor isequipped with an operator presence sensing
switch. When engine is running,any attempt by the operator
to reave the seat without first setting the parking brake will
shut off the engine.
• Depress clutch/brake pedal into full "BRAKE" position
and hold.
Place parking brake lever in "ENGAGED" position and
release pressure from clutch/brake pedal. Pedal should
remain in "BRAKE" position. Make sure parking brake
will hold tractor secure.
CHOKE _
CONTROL "_ _-_(" .
CONTROL ',_ _'_
POSITION p._
CLUTCH/BRAKE
PEDAL "DRIVE"
POSITION
,ATTACHMENT CLUTCH
LEVER "ENGAGED"
POSITION
IGNITION KEY
--"DISENGAGED"
POSITION
..PARKING BRAKE
--4',,;- - - - - - , "ENGAGED" PosmoN
PARKING BRAKE GEAR SHIFT
"DISENGAGED" LEVER
POSITION
FIG. 6
STOPPING (See Fig. 6)
MOWER BLADES -
• To stop mower blades,move attachment clutch lever to
"DISENGAGED" position.
GROUND DRIVE-
To stop ground drive, depress clutch/brake pedal into
full "BRAKE" position.
• Move gear shift lever to neutral (N) position.
ENGINE -
Move throttle control to slow position.
NOTE: Failure to move throttle control to slow position and
allowing engine to idle before stopping may cause engine to
"backfire".
Turn ignition key to "OFF' position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
• Never use choke to stop engine.
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY
POSITION OTHER THAN "OFF" WILL CAUSE THE
BATTERY TO BE DISCHARGED, (DEAD).
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases
may cause "browning" of grass. To eliminate this
possibility, always stop engine when stopping tractor on
grass areas.
CAUTION: Always stop tractor com-
pletely, as described above, before leav-
ing the operator's position; to empty
grass catcher, etc.
TO USE THRO'n'LE CONTROL (See Fig. 6)
Always operate engine at full throttle.
• Operating engine at less than full throttle reduces the
batterycharging rate.
• Full throttle offers the best bagging and mower perfor-
mance.
TO USE CHOKE CONTROL
(See Fig. 6)
Use choke controlwhenever you are starting a coldengine.
Do not use to start a warm engine.
• To engage choke control, pull knob out. Slowly push
knob in to disengage.
TO MOVE FORWARD AND BACKWARD
(See Fig. 6)
The direction and speed of movement is controlled by the
gearshift lever.
• Start tractor with clutch/brake pedal depressed and
gearshift lever in neutral (N) position.
• Move gear shift lever to desired position.
• Slowly release clutch/brake pedal to start movement.
IMPORTANT: BRING TRACTOR TO A COMPLETE STOP
BEFORE SHIFTING OR CHANGING GEARS. FAILURE TO
DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR
TRANSAXLE.
TO ADJUST MOWER CUTTING HEIGHT (See
Fig. 6)
The position of the attachment lift lever determines the
cutting height.
Grasp lift lever.
• Press plunger with thumb and move lever to desired
position.
The cutting height range is approximately 1-1/2 to 4". The
heights are measured from the ground to the blade tip with
the engine not running. These heights are approximate and
may vary depending upon soil conditions, height of grass
and types of grass being mowed.
• The average lawn should be cut to approximately 2-1/2
inches during the cool season &rid to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
• For best cutting performance, grass over 6 inches in
height should be mowed twice. Make the first cut
relatively high; the second to desired height.
11