Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for REXON M2503R
Summary of Contents for REXON M2503R
- Page 1 ® 10 IN. (255 MM) MITER SAW M2503R INSTRUCTION MANUAL...
- Page 2 CONTENTS P 1 - 8 The original instruction manual is in English.
-
Page 3: Carton Contents
CARTON CONTENTS UNPACKING 1. Carefully remove the miter saw from the carton. 2. Separate and layout all of the parts. Carefully check them according to the diagram below. IMPORTANT: Always use the designated carrying handle and hand-hold on the side of the saw base for transportation. -
Page 4: General Safety Rules
General Safety Rules for the connection of dust extraction and collecting equipment, ensure these are WARNING! When using electric tools connected and properly used. basic safety precautions should always 11. DO NOT ABUSE THE CABLE. Never be followed to reduce the risk of fire, pull the cable to disconnect it from the electric shock and personal injury. -
Page 5: Additional Safety Rules For Miter Saws
of parts, mounting and any other manufacturer. Do not use HSS (High conditions that may affect its operation. Speed Steel) blades or any other blade A guard or other part that is damaged that does not conform to EN847-1. should be properly repaired or replaced Damaged, warped or deformed blades by an authorised service centre unless should not be used. -
Page 6: Environmental Protection
Wear safety goggles. of the workpiece from the cutting Wear ear protection. area whilst the machine is running Wear a breathing mask. and the saw head is not in the rest position; WARNING! To reduce the risk of Ensure that the machine is always ●... -
Page 7: Installation
Installation Assembly WARNING! For your own safety, never KNOW YOUR MITER SAW (FIG. 1) connect the plug to power source outlet ON/OFF trigger switch handle until all assembly steps are completed Safety lock and you have read and understood the Upper blade guard safety and operational instructions. -
Page 8: Installing The Hold-Down Clamp
Locking the cutting head: SAW BLADE WRENCH (FIG. 7) 1. Push the cutting head down to its lowest 1. For convenient storage and prevention position. of loss, there is a slot (1) in the rear side 2. Push the head hold-down latch (2) into of the carrying handle for storing the the locking hole to lock the cutting head. -
Page 9: Connecting To The Power Supply
MITER ANGLE ADJUSTMENT (FIG. 9) 4. Repeat until adjusted properly, and The miter saw scale can be easily read tighten the lock nut (1) to secure the showing miter angles from 0° to 47° to the adjustment bolt (2) into position. left and the right. -
Page 10: Changing Blades
BASIC MITER SAW OPERATIONS Changing Blades It is recommended to use the clamp to ● hold the work piece firmly. WARNING! Do not use a blade larger than Always position the workpiece against ● 255 mm in diameter. To avoid injury from the fence. -
Page 11: Installing The Blade
INSTALLING THE BLADE Maintenance (FIG. 15, 16, 17) Unplug the miter saw before changing/ WARNING! For your own safety, turn the installing the blade. switch off and remove the plug from the 1. Install a 255 mm blade with a 25.4 mm power source outlet before maintaining arbor hole with a 16 mm reducer making or lubricating your miter saw. - Page 12 Fig. 1 Fig. 2 Fig. 5 Fig. 3 Fig. 6 Fig. 4 Fig. 7...
- Page 13 Fig. 8 Fig. 11 Fig. 9 Fig. 12 Fig. 10 Fig. 13...
- Page 14 Fig. 14 Fig. 15 Fig. 16 Fig. 17...
- Page 15 M2503R PARTS LIST ORDER ONLY BY MODEL NUMBER AND PART NUMBER I.D. Description Size Q'ty I.D. Description Size Q'ty 07WD SLIDE PLATE 20X3 KNOB 0831 SHAFT SLEEVE 21GM FLAT WASHER φ4*10-1 083Y COMPRESSION SPRING 23NX CORD GUARD 083Z CORD CLAMP...
- Page 16 Schematic MODEL: M2503R...
- Page 17 M2503R MOTOR PARTS LIST ORDER ONLY BY MODEL NUMBER AND PART NUMBER I.D. Description Size Q'ty 0HX9 NEEDLE BEARING 0JCD SPRING PIN 0JX7 HEX. SOC. SET SCREW M6*1.0-6 0K43 CR. RE. PAN HD. SCREW & WASHER M5*0.8-16 0K44 CR. RE. PAN HD. SCREW & WASHER M5*0.8-12...
- Page 18 NOTES...
- Page 19 NOTES...
- Page 20 ®...