Summary of Contents for yacht beam YB 1MM+
- Page 1 PRODUCT SUPPORT MANUAL YACHT BEAM 1MM+ Searchlight Remote Control System The Yacht Group - 4545 Ponce de Leon Blvd. Coral Gables FL 33146 Tel. 305.667.5811 - Fax. 305.663.5551 - www.TheYachtGroup.com...
-
Page 2: Table Of Contents
APPENDIX - SPECIFICATIONS APPENDIX - WIRING DIAGRAM APPENDIX - WARRANTY, NOTICES PLEASE READ ALL WARNINGS, CAUTIONS AND NOTES CAREFULLY. CAUTION: Before proceeding to install, test or use your new Yacht Beam product, please read this Product Support Manual in its entirety. -
Page 3: Section 1 - Product Description
SECTION 1 - PRODUCT DESCRIPTION Introduction The Yacht Beam 1MM+ was specially designed for mariners who require a high intensity remote controlled searchlight that can stand up to the tough marine environment. The sleek design and modern construction of the searchlight body makes it attractive for recreational and commercial ves- sels. -
Page 4: Section 2 - Searchlight Mounting
360° without hitting any obstructions. For the drilling hole pattern, refer to the searchlight Mounting Template. CAUTION: Do not mount the searchlight upside down. Moisture cannot drain from the inverted light head assembly. Joystick Yacht Beam 1MM+ Figure 2 - Master Controller unit (mounted upright) Joystick connection configuration... -
Page 5: Section 3 - Remote Control System
SECTION 3 - REMOTE CONTROL SYSTEM The Remote Control System consists of the Master Controller and the Joystick. This system is compatible with 12 VDC through 24 VDC systems without modification. SECTION 4 - JOYSTICK Flush Mount Cut a round hole of 7/8” in the surface, peel off protective covering of hi-bond tape from the mounting plate. Use the supplied prep on the mounting surface, place and press the Joystick in place. -
Page 6: Section 5 - Master Controller
1- Install the Thumb switch with LED Halo in dash. 2- Mount Yacht Beam Master Control box within 6 Feet of Thumb switch. 3- Connect Red and Black wires (12/2) from the Master control box (Power In), to 12 or 24 Volts D/C and... - Page 7 WARNING: The Yacht Beam 1MM+ has a unique wiring scheme. Special attention must be paid to the following chart. WARNING: Failure to follow this arrangement may damage components. DIRECTION CONTROL WIRING Wiring from Interface box 16/4 Spotlight harness White White...
-
Page 8: Section 6 - Joystick Operation
• Press the ON/OFF button to turn the lights ON or OFF and the halo light will illuminate. • Press the Joystick RIGHT or LEFT and the halo ring will light up to confirm the movement. • Press the Joystick FORWARD or BACK to raise or lower the searchlight beam. Figure 6 Yacht Beam 1MM+... -
Page 9: Section 7 - Wireless Remote Control
SECTION 7 - WIRELESS REMOTE CONTROL INSTALLATION & OPERATION INSTRUCTIONS 1- Remove (4) screws at corners of Top cover of Master Control box. 2- Connect Plug from the RC Top Cover to Socket located in the upper Left corner of Master Control Box. 3- Secure new cover with the 4 screws. -
Page 10: Appendix - Specifications
APPENDIX - SPECIFICATIONS CHARACTERISTICS SPECIFICATIONS Size 12 X 13 X 9.3 in (31 X 33 X 23.5 cm) Weight 31 lb (14.06 kg) Material Cast aluminum, tempered glass Input voltage* 12V- 24V Amp draw Startup 25A @ 12V, Running 8A @ 12V Color White Operation... -
Page 11: Appendix - Wiring Diagram
APPENDIX - WIRING DIAGRAM YACHT BEAM 1MM+... -
Page 12: Appendix - Warranty, Notices
This product is warranted against factory defect in material and workmanship for a period of 1 (one)* year from date of purchase or receipt as a gift. During the warranty period Yacht Beam will have repaired, or at its option, replaced at no cost to you for labor, materials or return transportation.