1. Manuals
  2. Brands
  3. SteelMax Manuals
  4. Saw
  5. S-7 XP
  6. Operator's manual

SteelMax S-7 XP Operator's Manual

7 1/4 inch metal cutting circular saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL S-7 XP
(Part Number: SM-S-7 XP)
7¼" METAL CUTTING CIRCULAR SAW
OPERATOR'S MANUAL
,
TO REDUCE THE RISK OF INJURY
READ AND THOROUGHLY UNDERSTAND THIS
.
OPERATOR'S MANUAL
Always Wear Eye and
Never Place Line Voltage
Ear Protection
Hands Near
Present
Cutting Area
WWW.STEELMAX.COM
SM-S-7 XP Operator's Manual
2017 Version 1.10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S-7 XP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for SteelMax S-7 XP

Summary of Contents for SteelMax S-7 XP

  • Page 1 MODEL S-7 XP (Part Number: SM-S-7 XP) 7¼” METAL CUTTING CIRCULAR SAW OPERATOR’S MANUAL TO REDUCE THE RISK OF INJURY READ AND THOROUGHLY UNDERSTAND THIS OPERATOR’S MANUAL Always Wear Eye and Never Place Line Voltage Ear Protection Hands Near Present Cutting Area WWW.STEELMAX.COM...

  • Page 2: Table Of Contents

    Steelmax within thirty (30) days of the purchase date. This warranty is void if the tool being returned has been used beyond the recommendations in this Operator’s Manual or if the machine has been damaged by accident, neglect, improper service, or other causes not arising out of defects in materials or workmanship.

  • Page 3: Intended Use And General Safety Guidelines

    Intended Use and General Safety Guidelines The Steelmax S-7 XP Metal Cutting Saw is designed to rapidly cut mild steel and other similar materials without heating either the saw blade or the material being cut. The S-7 XP can easily cut mild steel sheet metal up to ¼”...
  • Page 4 Many accidents are caused by poorly maintained tools. • Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SM-S-7 XP Operator’s Manual - 2 - 2017 Version 1.10...
  • Page 5 • When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury and will void the warranty. SM-S-7 XP Operator’s Manual - 3 - 2017 Version 1.10...

  • Page 6: Specific Safety Rules And Symbols

    Always observe that the lower guard is covering the blade before placing saw down on bench • or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting SM-S-7 XP Operator’s Manual - 4 - 2017 Version 1.10...
  • Page 7 WARNING! DO NOT USE TINTED GLASSES TO ENHANCE THE LASER LIGHT. Tinted glasses will reduce overall vision for the application and interfere with the normal operation of the tool. SM-S-7 XP Operator’s Manual - 5 - 2017 Version 1.10...
  • Page 8 Check lower guard for proper closing before each use. Do not operate the saw if lower guard • does not move freely and close instantly. Never clamp or tie the lower guard into the open SM-S-7 XP Operator’s Manual - 6 - 2017 Version 1.10...
  • Page 9 Replace or repair damaged cords. Make sure your extension cord is in good condition. Use • only 3-wire (minimum 14 gauge) extension cords that have 3-prong grounding-type plugs and 3-pole receptacles that accept the tool’s plug. SM-S-7 XP Operator’s Manual - 7 - 2017 Version 1.10...
  • Page 10 S-7 XP Parts Diagram SM-S-7 XP Operator’s Manual - 8 - 2017 Version 1.10...

  • Page 11: Parts List

    Steelmax S-7 XP Parts List Steelmax Part Steelmax Part Ref. No. Number Description Quantity Ref. No. Number Description Quantity SMS7XP-1 Lock Bolt SMS7XP-48 Overload Protection SMS7XP-2 Outer Cover SMS7XP-49 Cord Clamp SMS7XP-3 Glass SMS7XP-51 Self Tapping Screw SMS7XP-4 Chip Shield...

  • Page 12: Assembly And Adjustment

    ASSEMBLY AND ADJUSTMENT INSTRUCTIONS Your Steelmax® S-7 XP saw is shipped complete and protected inside a reusable carrying case. Remove all contents from the case and inspect to ensure no damage occurred during shipping. DESCRIPTION PART NUMBER QUANTITY SM-7 XP METAL CUTTING SAW SM-S-7 XP 7-1/4”...

  • Page 13: Installing A New Saw Blade

    Check that the blade to be used is flat, sharp and free of damage or defects. 1. Change blade: Loosen the lock bolt (A) and remove chip shield assembly. Fig.1 2. Remove included 6 mm Allen wrench (A). Fig.2 SM-S-7 XP Operator’s Manual - 11 - 2017 Version 1.10...
  • Page 14 (A) to secure the motor shaft while tightening the shaft screw (B). Fig.5 Assemble chip shield assembly with blade housing and re-tighten lock bolts ((B)，Fig.1 Be sure to repalce Allen wrench for future use. SM-S-7 XP Operator’s Manual - 12 - 2017 Version 1.10...

  • Page 15: Laser Guide Use And Adjustment

    Laser Guide Use and Adjustment 1. Plug power cord into appropriate power supply and turn on the laser on/off switch. Laser (B) will illuminate. Fig.7 2. Laser guide automatically follows bevel angle. Fig.8. SM-S-7 XP Operator’s Manual - 13 - 2017 Version 1.10...
  • Page 16 3. Adjust the laser and return zero position by adjusting the guide ruler (A) and back base to zero position (B). The laser indication needs to close U shape gap (C). Fig.12. SM-S-7 XP Operator’s Manual - 14 - 2017 Version 1.10...

  • Page 17: Saw Trigger Switch Operation

    Saw Trigger Switch Operation Press the stop button (A) and pull the Trigger Switch (B) at the same time to start saw motor. Saw stops automatically when Trigger Switch is released. Fig.15 SM-S-7 XP Operator’s Manual - 15 - 2017 Version 1.10...

  • Page 18: Proper Saw Operation

    Chip accumulation can be obsrved throgh the clear viewing window on the side of the saw. When the chip collection area reaches half-full, remove the guard by loosening the two bolts. Empty the guard of its contents and re-install. Fig. 19, 20 SM-S-7 XP Operator’s Manual - 16 - 2017 Version 1.10...
  • Page 19 Beware: Always keep the saw away from your body when removing the chip shield to avoid spilling chips on your person or clothing. The chips can be very hot. SM-S-7 XP Operator’s Manual - 17 - 2017 Version 1.10...

  • Page 20: Saw Maintenance

    Remove the power cord from the power supply before carrying out any adjustment, servicing or maintenance on your Steelmax saw. Keep the machine clean and never use a saw blade that is damaged or distorted. Replace the saw blade when it becomes dull. For service and replacement pieces see the exploded parts diagram and parts list.

  • Page 21: Troubleshooting

    Aggressive contact with blade into material. The blade must be allowed to do the work. • Too much vibration due to insufficient clamping of workpiece, worn or bent blade, or worn parts (see "Saw Vibrates" below). SM-S-7 XP Operator’s Manual - 19 - 2017 Version 1.10...
  • Page 22 Check bevel lock and depth lock for tightness. • Check for missing teeth, bends or cracks in the blade 7. Laser Won’t Track • Adjust Laser alignment with laser turned on. STEELMAX S-7 XP SPECIFICATONS Rated Voltage 120V, 60Hz Motor Power 1,560W No Load Motor Speed...
  • Page 23 Laser radiation. Avoid direct eye contact with light source. Caution: When cutting do not touch the metal parts that may become hot. Caution: Laser radiation - do not stare into beam Laser Radiation Caution Label SM-S-7 XP Operator’s Manual - 21 - 2017 Version 1.10...
  • Page 24 PRODUCT INFORMAITON ® Thank you for purchasing a Steelmax product! Please record the following information and keep this page for your records. MODEL: S-7 XP METAL CUTTING SAW SERIAL NUMBER: PURCHASE DATE: PURCHASED FROM: SM-S-7 XP Operator’s Manual - 22 -...

This manual is also suitable for:

Sm-s-7 xp

Table of Contents