Related Manuals for NOYAFA NF-8601
Summary of Contents for NOYAFA NF-8601
- Page 1 NF-8601 Your excellent helper in cable test! NF-8601/ NF-8601A/ NF-8601W Instruction Manual Cable Length Tester Your excellent helper in cable test! ORIGINAL ORIGINAL AUTHENTIC AUTHENTIC REV1.0...
- Page 2 CONTENTS Read the precautions before your operation. Overview..............01 Main functions ............02 Technical Parameters..........02 Power supply for device is 3.7V rechargeable lithium battery. ● Product interface and key introduction.....04 Disconnect the 5V 1A Charger when complete charging in fear of ● danger.
- Page 3 Main functions Capable to test open, short, cross connection, reverse, and ● NF-8601 Series are newly developed by our company which are broken wire positioning with M-S, M-R method. capableofanti current interference . The equipment is composed of To perform crosstalk test on network cable to solve the potential ●...
- Page 4 The other one is “PoE/PING” interface, used for (13). Tracing cable PoE and PING Testing. Locate targeted cable among lots of cables (only for NF-8601 & (2) Port RJ11: used for tracing cable, cable length and continuity testing for NF-8601W, NF-8601A Can't) telephone cable .
- Page 5 Instruction on Main interface Menu Receiver Wire apping P i n g Scan able Portson Receiver MICRO: Charging for battery. Function keys on Receiver Cable ength POE Test is to detect currency and also lighting lamp. “SET” is for voltage detector and cable tracing.
- Page 6 Operation steps Note: M-R Methods is for cable continuity testing, not for cable length measuring. Boot screen (3) Scan method---“ RJ45 Scan”“RJ11”“ BNC” Turn on the tester to come to home page. ports are used to trace corresponding cables. ( Graph No.3) 您的布线专家! Graph No.3 www.jingmingshu.cn...
- Page 7 a.Cable line-to-line test ( eg: Network cable): Test result 3: correct connection If the device connects corrected, the tester can check remote identifier (R), After entering main menu, move the cursor button to cable on-off test. or local port (S) cables. If Verify the tested cable with remote ( R) or local Then press OK;...
- Page 8 Test result 10: Continuity test for BNC cable Note: Because network cable is made of pair cores, if there is open circuit, When you test the BNC cable , you should insert into the BNC interface and it will show faults in pairs, just as above "4" &" 5". it means either "4" pin or "5"...
- Page 9 Special Use: network detection b.Cable length test:( eg: Network cable) Our this main tester can test line sequence under the switches work on. After entering main menu, move the cursor button to Cable length Network cable as the example---One side connect the main tester's RJ45 test.
- Page 10 Test result 1: The commonly used Network cable Test result 3 : Normal CAT6 The normal network cable length test result show you as below: The normal cat 6 cable length test result show you as below: CAT6 Cable Length RJ45 able ength...
- Page 11 Test result 5 : Normal 6 cores telephone cable Test result 7: BNC cable length test If you want to test Telephone cable , one side insert the main tester RJ11 If to insert one end of the BNC cable to be tested into “BNC” port of the main interface and the other side connect nothing , then choose Telephone test tester, the other end is an open circuit, select “BNC(2)”...
- Page 12 Calibration: eg: Network cable After entering main menu, move the cursor button to Cable length test. Then press OK; at this time, choose network cable, press OK, Due to different technical parameters with different branded cables, users and choose parameter callout menu, press OK to choose the data where are recommended to use dynamic calibration function of the equipment you saved.
- Page 13 c. Cable tracing test ( NF-8601A without this function) 1. Tracing cable (RJ45/RJ11 Cable) which is connected to switch or router. After entering main menu, move the cursor button Then press Insert the cable into port RJ11/ RJ45 (S), Press the testing key of receiver, OK to scan;...
- Page 14 3. Locate the short or breakage point ( eg : Metal cable) d. Crosstalk test Connect the metal cable with the cable clips , press the testing key of As shown the figure below: it shows 3, 6 and 4, 5 with crosstalk. The line pair receiver , hold the receiver close to the cables , “...
- Page 15 If you want to save the tested result, you can choose data export into the TF Menue Ping Configure card, the picture show you as below: : 192.168.1.1 estination IP : 192.168.1.110 ocal IP Wire apping Scan able P i n g Default Router : 192.168.1.1 P i n g...
- Page 16 Shutdown When you finished all the operation, please remember shut down the device to keep it. NF-468L NF-300 NF-HDMI Thank you for using noyafa’s product welcome to use next time bye! NF-701 NF-905 NF-906A Your excellent helper in cable test!
Need help?
Do you have a question about the NF-8601 and is the answer not in the manual?
Questions and answers