Related Manuals for Techpro IP-EL Series
Summary of Contents for Techpro IP-EL Series
- Page 1 IP-EL Series - User's Manual Guaranteed Control View From Motion Warranty Anywhere Resolution Activated Recording...
- Page 2 Welcome Thank you for purchasing our IP camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference! Our units do not support PAL Important! To find your cameras on the network, use the "config Tool"...
-
Page 3: Important Safeguards And Warnings
Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC in the IEC60950-1.This series product supports PoE too. Please note: Do not connect these two power supplying sources to the device at the same time;... - Page 4 Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device.
-
Page 5: Table Of Contents
Table of Contents General Introduction ........................Overview........................Features......................... Camera Installation....................... Varifocal lens........................Structure ............................Multiple-function Combination Cable ................ Framework and Dimension..................Quick Configuration Tool......................Overview........................Operation........................FAQ ............................. Appendix Toxic or Hazardous Materials or Elements .............. -
Page 6: General Introduction
1 General Introduction 1.1 Overview This series IP camera integrates the traditional camera and network video technology. It adopts video data collection, transmission together. It can connect to the network directly without any auxiliary device. This series IPC uses standard H.264 video compression technology, which maximally guarantees the video quality. -
Page 7: Camera Installation
1.3 Camera Installation Dome Installation Step 1 If included please take the installation position map from the accessories bag, and then paste it on the ceiling or the wall according to your monitoring area requirements. Draw and then drill holes in the installation surface and then insert expansion(anchor) bolts in the holes. - Page 8 Metal Housing Ceiling or Wall Expansion Bolt Pedistal 1 ST3 Self-tapping Screws Glass Enclosure Ceiling or Wall Installation Position Map Expansion Bolts Enclosure fastening screw Socket Screw Inner Hex Wrench...
- Page 9 Box Camera Lens Installation Auto Aperture Lens Please follow the steps listed below for auto aperture lens installation. Remove the CCD protection cap of the device, and then line up the lens to the proper installation position. Turn clockwise until the lens is fixed firmly. ...
- Page 10 Bullet Installation Sun Shield Cover Bracket Before you install the bracket, please pull the cable through the cable exit of the bracket chassis. Important The installation wall shall min sustain 3X weight of the bracket and camera. Step 1 Paste the installation map on the surface of the wall or the ceiling. Step 2 Dig the installation holes according to the installation map.
- Page 11 Step 3 Open the accessories bag and then take the expansion bolt out. Insert the expansion bolt into the installation holes. Step 4 Take the screws from the accessories bag and then use them to secure the device on the installation surface of the wall or the ceiling.
- Page 12 1.4 Variofocal lens Each camera will be a little different. Some adjustable lens cameras are adjusted manually on the camera. VariFocal Camera In other cameras the adjustable lever can be Unscrew M2 5*5 Bolt from the found in the inside of the lower cover of the camera.
-
Page 13: Multiple-Function Combination Cable
2.1 Multiple-function Combination Cable You can refer to the following figure for multiple-function combination cable information. See Figure Figure 2-1 Please refer to the following sheet for detailed information. Port Name Function Connection Note Ethernet 1.LAN Network port Connect to standard Ethernet cable. port Power input... -
Page 14: Quick Configuration Tool
3 Quick Configuration Tool Please refer to the CD to find Configtools.exe 3.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 3.2 Operation Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure 3-1. - Page 15 Figure 3-2 Select the “Open Device Web” item; you can go to the corresponding web login interface. See Figure 3-3. Figure 3-3 If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set.
- Page 16 Figure 3-4 After you logged in, the configuration tool main interface is shown as below. See Figure 3-5. Figure 3-5 For detailed information and operation instruction of the quick configuration tool, please refer to the Quick Configuration Tool User’s Manual included in the resources CD.
-
Page 17: Web Operation
4 Web Operation This series IPC product support the Web access and management via PC. Web includes several modules includes monitor channel preview, system configuration, alarm and etc. 4.1 Network Connection Please follow the steps listed below for network connection. Make sure the IPC has connected to the network properly. - Page 18 If it is your first time to login in, system pops up warning information to ask you whether install control webrec.cab or not after you logged in for one minute. Please click OK button, system can automatically install the control. When system is upgrading, it can overwrite the previous Web too. If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the control download.
- Page 19 Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction.
-
Page 20: Faq
5 FAQ I can not boot up Please click RESET button for at least five seconds to restore the device or factory default setup. operate properly. The water leakage The unauthorized front or rear cap remove many result in water occurred. -
Page 21: Appendix Toxic Or Hazardous Materials Or Elements
Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component Device Construction ○ ○ ○ ○ ○ ○ Material Wire and Cable ○ ○...