Advertisement
Damage caused by violating instructions in this user
manual void warranty. Manufacturer accepts no liability
for any product issues that result from disregard of this
manual.
• UNPACKING YOUR WRX-843
Please inspect product for any damage from transport
before unpacking. If damages are present, do not operate.
Immediately contact your local dealer to inspect damage
and conduct possible exchange.
• PROTECTION CLASS
The WRX-843 Protection Class I. The power plug must
only be plugged into a Protection Class I outlet, with
matching voltage and frequency as stated on device.
Incorrect voltages or power outlets can lead to product
damage and risk of electrical shock to user.
• POWER CORD
When ready to operate, always plug in power cord last.
Make sure the plug is tightly connected with the outlet
and away from other cables. Always handle with caution.
Never touch with wet hands, modify, bend, strain, put
pressure on, pull or expose to heat. This could cause fire
or electrical shock to user.
If extension cords are used, check that core diameter
is sufficient for the required power consumption. All
warnings presented for device power cords apply to
valid extension cords.
Always disconnect completely when device is not is use
and before cleaning it. Only handle power cord by the
plug; never pull plug from outlet or device by the cord.
If device must be cleaned, cease operation, disconnect
fully, and clean with a dry cloth. Severe levels of dirt and
dust should be removed by a specialist.
• LIQUIDS
There must never enter any liquid into power outlets,
extension cords or any holes in the housing of the
device. If you suppose that also a minimal amount of
liquid may have entered the device, it must immediately
be disconnected. This is also valid, if the device was
exposed to high humidity. Also if the device is still
running, the device must be checked by a specialist if
the liquid has reduced any insulation. Reduced insulation
can cause mortal electrical shock.
• FOREIGN OBJECTS
Under no circumstances should there be objects entering
the device casing, especially metal. If any substance
enters the device, take out of operation immediately and
disconnect. Any malfunction or short circuiting caused
by foreign objects can cause serious injury or even
death. Consult manufacturer on repair or replacement.
• SECURE SETUP
Be aware speaker system could move due to bass
sounds and vibrations. Any unintended pushes from
performers or audience present furthers risk. Speaker
system should always be secured in place away from
moving elements.
• PRIOR TO SWITCHING ON
Before the speaker system is switched on, set all faders
and volume controls to zero.
• CHILDREN
Keep children and inexperienced users away from unit to
prevent accidents and injuries.
• Maintenance and Service
Maintenance and service operations are only to be carried
out by authorized dealers and manufacturer.
This high-performance active speaker system sits inside
a light-weight plastic cabinet. Use it for permanent
installations and professional live applications.
Connect with microphones, line sources and other
speaker systems.
• POWER SUPPLY
This system can be operated with an alternating current of
100-240V, 50/60 Hz and is designed for indoor use only
Cable
Pin
International
Brown
Live
L
Blue
Neutral
N
Yellow/Green
Earth
If the device is connected with the loal power supply
network, a disconnect switch with a minimum opening
of 3mm at every pole has to be included in the permant
electrical installation, in compliance with IEC standards.
The electric installation must be equipped with a Residu-
al Current Device (RCD) with maximum fault of 30mA.
• PUBLIC AND INDUSTRIAL USE
If operating this system in public or industrial areas, the
operator must inform him/herself on all current safety
instructions contained in this manual and elsewhere.
• MAXIMUM POWER
Never exceed the maximum power of this speaker. When
operating, distortions heard signify amplifier or speaker
being overloaded, which can lead to speaker damage. To
avoid permanent damage, reduce volume immediately.
Damage from overload voids warranty.
• ADMISSIBLE TEMPERATURES
Ambient temperature must be kept between -5 C and
+45 C. Keep away from direct insulation and heaters.
• OPERATION
Do not operate without fully familiarizing self with haz-
ards and instructions first. Do not permit inexperience
users or children to operate. Most damage occurs as
result or unprofessinoal operation.
• TRANSPORT
Move carefully, never forcing parts during assembly or
disassembly. Use original packing to transport device. If
original packing is unavailable, use proper fitting,
protective casing.
• CLEANING
Never use solvents or aggressive detergents to clean
device. Use soft, damp or dry cloth.
• INSTALLATION
Only install this device on a solid anti-slip, vibration-free,
oscillation-free and fire resistant plane. Make sure surface
can hold a minimum point of 5x the system's load.
System should never be installed higher than 100cm
without secondary attachment.
• Modifications and Guarantee
Unauthorized modifications made to the speaker system
are prohibited due to higher potential for damage.
Unauthorized modifications made void speaker warranty.
Unauthorized modifications can lead to system damage,
crashes, hearing damage, etc.
FEATURES // English //
1. Jack or XLR MIC Input.
9. Pwr/limit LED.
2. Reverb Switch.
10. MIX output.
3. MIC/LINE Switch.
11. ReverbVolume.
4. MIC/LINE Volume.
12. RCA Input.
5. AUX/RCA Volume.
13. AUX Input.
6. Bluetooth Pair.
14. AC Input.
7. Master Volume.
15. Power Switch.
8. Preset DSP Switch.
16. AC Voltage Switch.
CARACTERÍSTICAS // Español //
1. Jack o Entrada XLR MIC.
10. MIX salida.
2. Interruptor de reverberación.
11. ReverbVolume.
3. Conmutador MIC / LINE.
12. Entrada RCA.
4. Volumen MIC / LINE.
13. Entrada AUX.
5. Volumen AUX / RCA.
14. Entrada de CA.
6. Par Bluetooth.
15. Interruptor de encendido.
7. Volumen maestro.
16. Interruptor de Voltaje AC.
8. Conmutador DSP preajustado.
9. Pwr / límite LED.
4
4
3
3
2
2
1
1
16
CARACTÉRISTIQUES // Français //
1. Jack ou XLR MIC Input.
10. Sortie MIX.
2. Interrupteur de réverbération.
11. ReverbVolume.
3. Interrupteur MIC / LINE.
12. Entrée RCA.
4. Volume MIC / LINE.
13. Entrée AUX.
5. Volume AUX / RCA.
14. Entrée AC.
6. Paire Bluetooth.
15. Interrupteur d'alimentation.
7. Master Volume.
16. Interrupteur de tension CA.
8. Commutateur DSP préréglé.
9. Pwr / limite LED.
EIGENSCHAFTEN // Deutsch //
1. Klinken- oder XLR-MIC-Eingang.
2. Reverb-Schalter.
10. MIX-Ausgang.
3. MIC / LINE Schalter.
11. ReverbVolume.
4. MIC / LINE Lautstärke.
12. RCA-Eingang.
5. AUX / Cinch-Lautstärke. 13. AUX Eingang.
6. Bluetooth-Paar
14. AC-Eingang.
7. Master Volume.
15. Netzschalter.
8. Preset DSP Switch.
16. Wechselspannungsschalter.
9. Pwr / Limit LED.
5
7
8
6
9
12
11
10
13
15
14
Advertisement
